Search Results

It is well known that ethanol can be used in spark-ignition (SI) engines as a pure fuel or blended with gasoline. High enthalpy of vaporization of alcohols can affect air-fuel mixture formation prior to ignition and may form thicker liquid films around the intake valves, on the cylinder wall and piston crown. These liquid films can result in mixture non-homogeneities inside the combustion chamber and hence strongly influence the cyclic variability of early combustion stages. Starting from these considerations, the paper reports an experimental study of the initial phases of the combustion process in a single cylinder SI engine fueled with commercial gasoline and anhydrous ethanol, as well as their blend (50%vol alcohol). The engine was optically accessible and equipped with the cylinder head of a commercial power unit for two-wheel applications, with the same geometrical specifications (bore, stroke, compression ratio).

This paper reports the study of the effects of alternative diesel fuel and the impact for the air-fuel mixture preparation. The injection process characterization has been carried out in a non-evaporative high-density environment in order to measure the fuel injection rate and the spatial and temporal distribution of the fuel. The injection and vaporization processes have been characterized in an optically accessible single cylinder Common Rail diesel engine representing evaporative conditions similar to the real engine. The tests have been performed by means of a Bosch second generation common rail solenoid-driven fuel injection system with a 7-holes nozzle, flow number 440 cc/30s @100bar, 148deg cone opening angle (minisac type). Double injection strategy (pilot+main) has been implemented on the ECUs corresponding to operative running conditions of the commercial EURO 5 diesel engine.

The present study proposes the use of a MLP neural network to model the relationship between the engine crankshaft speed and parameters derived from the in-cylinder pressure cycle. This allows to have an indirect measure of cylinder pressure permitting a real time evaluation of combustion quality. The structure of the model and the training procedure is outlined in the paper. The application of the model is demonstrated on a single-cylinder engine with data from a wide range of speed and load. Results confirm that a good estimation of combustion pressure parameters can be obtained by means of a suitable processing of crankshaft speed signal.

The match among the increasing performance demands and the stringent requirements of emissions and the fuel consumption reduction needs a strong evolution in the two-wheel vehicle technology. In particular, many steps forward should be taken for the optimization of modern small motorcycles and scooters at low engine speeds and high loads. To this aim, detailed understanding of thermo-fluid dynamic phenomena that occur in the combustion chamber is fundamental. In this work, low-cost solutions are proposed to optimize ported fuel injection spark ignition (PFI SI) engines for two-wheel vehicles. The solutions are based on the change of phasing and on the splitting of the fuel injection in the intake manifold. The experimental activities were carried out in the combustion chamber of a single-cylinder 4-stroke optical engine fuelled with European commercial gasoline. The engine was equipped with a four-valve head of a commercial scooter engine.

High spatial and temporal resolution optical techniques were applied in a spark ignition (SI) engine in order to investigate the thermal and fluid dynamic phenomena occurring during the combustion process. The experiments were realized in the combustion chamber of an optically accessible single-cylinder port-fuel injection (PFI) SI engine. The engine was equipped with a four-valve head and with an external boost device. Two fuel injection strategies at closed-valve and open-valve occurring at wide open throttle were tested. Cycle-resolved digital imaging was used to follow the flame kernel growth and flame front propagation. Moreover, the effects of an abnormal combustion due to the firing of fuel deposition near the intake valves and on the piston surface were investigated. Natural emission spectroscopy in a wide wavelength range from ultraviolet to infrared was applied to detect the radical species that marked the combustion phenomena in the selected operating conditions.

In this work, a boosted single-cylinder spark ignition port-fuel injection optical engine was used for the experimental activity. Firstly, it was equipped with a four-valve head of a commercial turbocharged multi-cylinder engine. Then a prototype engine head with flush installed intake valves was tested. The effect of the different head geometry was evaluated in closed intake valves fuel injection condition. High spatial resolution cycle-resolved digital imaging was used to characterise the flame propagation. Moreover, the presence of diffusion-controlled flames near the valves and on the cylinder walls was investigated. These flames induced the formation of unburned hydrocarbons and soot particles. The spatial distribution and temporal evolution of soot were evaluated by the two colour pyrometry. The prototype configuration showed higher combustion process efficiency than the standard one inducing a little increase in performance and a slight reduction in carbon oxides emissions.

The flame front propagation in normal and abnormal combustion was investigated. Cycle-resolved flame emission imaging was applied in the combustion chamber of a port fuel injection boosted spark ignition engine. The engine was fuelled with a mixture of 90% iso-octane and 10% n-heptane by volume (PRF90). The effect of fuel injection phasing was studied. The combustion process was followed from the flame kernel formation until the opening of the exhaust valves. Different phenomena correlated to the abnormal combustion were analysed. Detailed information on ignition surfaces, end-gas auto-ignitions and knock were obtained. The appearance of autoignition centres in the end gas was evaluated in terms of timing, location and frequency of occurrence.

Electronic engine controls based on non-intrusive diagnostics can significantly help in complying with the stricter and stricter regulations on pollutants emissions and fuel consumption. The aim of this paper is the use of a low-cost linear capacitive accelerometer placed on the engine block for non-intrusive diagnosis of combustion process in spark ignition engines. In particular, good correspondences between the engine block vibrations and the combustion pressure signal were obtained. The angular position of pressure peak evaluated by accelerometer data can be used in a closed-loop control system for real time control of spark advance.

The paper reports a numerical activity on the investigation of the spray evolution within the combustion chamber of an automotive DISI engine under low-temperature cranking operations. In view of the high injected fuel amount and the strongly reduced fuel vaporization at cold cranking, wall wetting becomes a critical issue. Under such conditions, fuel deposits around the spark plug region can affect the ignition process, and even prevent engine start-up. In fact, due to the low injection pressure at engine start-up, the fuel shows almost negligible atomization and breakup, and the spray structure at the swirl-type injector nozzle is characterized by a single column of liquid fuel, strongly limiting the subsequent vaporization and enhancing the fuel-wall interaction. In order to properly investigate and understand the many involved phenomena, experimental visualization of the full injection process by means of an optically accessible engine would be a very useful tool.

A satisfactory answer to the future severe normative on emissions and to the market request for spark ignition engines seems to be the use of downsized engines for passenger cars. Downsizing permits the increase in engines power and torque without the increase in cylinder capacity. The downsizing benefits are evident at part loads; on the other hand, more work should be done to optimize boosted engines at higher and full load. To this goal, a detailed knowledge of the thermo-fluid dynamic processes that occur in the combustion chamber is fundamental. The aim of this paper is the experimental investigation of the effect of the fuel injection in the intake manifold on the combustion process and pollutant formation in a boosted spark ignition (SI) engine. The experiments were performed on a partially transparent single-cylinder port fuel injection (PFI) SI engine, equipped with a four-valve head and boost device.

A 2200 cc engine head for marine applications has been analysed and optimized by means of both fluid-dynamic and thermo-structural simulations. First, the fluid distribution within the cooling jacket has been deeply investigated, in order to point out critical aspects of the current jacket layout and propose modified gaskets aiming at modifying the coolant path and increasing the cooling performance. A new generation polyhedral grid has been employed to combine high resolution surface spacing, computational demand, and numerical stability of the CFD simulations. Different turbulence models and near-wall approaches have been tested in order to accurately predict the boundary layer behaviour, which is fundamental for the subsequent thermal analysis. Comparisons have been carried out between the different gasket layouts in terms of both cylinder to cylinder flow balancing and cooling effectiveness in the critical regions of the engine head.

The growing demands on fuel economy and always stricter limitations on pollutant emissions has increased the interest in the ignition phenomena to guarantee successful flame development for all the spark ignition (SI) engine operating conditions. The initial size and the growth of the flame have a strong influence on the further development of the combustion process. In particular, for the new FIAT generation of turbocharged SI engines, the first times of spark ignition combustion are not yet fully understood. This is mainly due to the missing knowledge concerning the detailed physical and chemical processes taking place during the all set of the flame propagation. These processes often occur simultaneously, making difficult the interpretation of measurements. In the present paper, flame dynamic was followed by UV-visible emission imaging in an optical SI engine.

The aim of the present paper is to provide an insight into the fluid dynamic processes that occur during the air/fuel mixture formation period in direct injection diesel engines. An experimental and numerical investigation has been performed to analyse the mixing process between an evaporating diesel spray and a swirl air flow under realistic engine conditions. Experimental tests have been carried out spraying the fuel within an optically accessible prototype 2-stroke Diesel engine equipped with an external combustion chamber having cylindrical shape. The intake air flow, coming from the engine cylinder, is forced within the combustion chamber by means of a tangential duct generating a well structured swirl flow similar to that developing in a real light duty diesel engine with a high swirl ratio. A micro-sac 5-hole, 0.13 mm diameter, 150° spray angle electro-hydraulic injector supplies the fuel by a common rail injection system able to manage multiple injection strategies.

Aim of this work is to develop a general purpose model for combustion and knocking prediction in SI engines, by coupling a thermo-fluid dynamic model for engine simulation with a general detailed kinetic scheme, including the low-temperature oxidation mechanism, for the prediction of the auto-ignition behavior of hydrocarbons. A quasi-D approach is used to describe the in-cylinder thermodynamic processes, applying the conservation of mass and energy over the cylinder volume, modeled as a single open system. The complex chemistry model has been embedded into the code, by using the same integration algorithm for the conservation equations and the reacting species, and taking into account their mutual interaction in the energy balance. A flame area evolution predictive approach is used to evaluate the turbulent flame front propagation as function of the engine operating parameters.

The aim of the paper is to provide information about the in-cylinder flow field optimisation in a high speed, direct injection (HSDI) four valve per cylinder diesel engine for off-highway applications. Fully transient CFD analyses of different valve profile strategies for the intake and compression strokes are at first performed, in order to evaluate the effects on both engine permeability and in-cylinder flow field evolution. Modifications are applied to each intake valve separately: gradually stretched cam profiles are imposed so that strategies range from the standard operation, i.e. the adoption of a unique cam profile for the two intake valves, up to the limit case characterized by a 40 % difference between the intake valves maximum valve lifts for three different engine conditions.

Two different optical techniques for detection, sizing and counting nanoparticles were applied to undiluted exhaust from 16 v–1900 cc Common Rail diesel engine upstream and downstream a Catalyzed Diesel Particulate Filter (CDPF): Broadband Ultraviolet–Visible Extinction and Scattering Spectroscopy (BUVESS) and Laser Induced Incandescence (LII). They are powerful “in situ” and non-intrusive techniques; they are able to measure mass concentration and size of particles, considering their chemical properties. BUVESS overcomes the intrinsic limitations of single wavelength techniques because it takes advantage of data at several wavelengths to retrieve primary particle size distribution. LII measures mean size of primary particles with a large dynamic range, not limited by aggregate size and by complex retrieving procedure.

Actual emission legislation limits strongly the amount of pollutant in the atmosphere from internal combustion engine. In particular diesel engines widely emit NOx and particulate matter (PM). The last one has principally a carbonaceous nature and presents micronic and submicronic particles extremely dangerous for human health since it could deposit in the lung. In this work, a technique based on broadband ultraviolet (UV) visible scattering and extinction is applied inside a transparent DI CR diesel engine in order to analyze the soot evolution and oxidation. The study is carried out with particular detail for different injection strategies characterized of two and three injections per cycle, Pre+Main and Pre+Main+Post, considering the late combustion before the exhaust stroke. The analysis is performed in terms of size, mass concentration, and chemical and physical nature.

The aim of the paper is the characterization in terms of chemical and physical nature of particles at exhaust of spark ignition (SI) engine. Measurements were carried out at exhaust of 16v - 1.2 litre Port Fuel Injection Spark Ignition engine downstream a catalyst. The emission of nanoparticles was investigated by optical techniques and conventional methods. In particular laser induced incandescence (LII), and broadband multiwavelength extinction-scattering spectroscopy (BUVESS) were used. LII allowed the detection and sizing primary particles of carbonaceous nature. BUVESS measured particle size distribution by numerical procedure that took advantage by data at several wavelengths. The optical results were compared with those obtained by conventional methods like opacimeter for mass concentration and Electrical Low Pressure Impactor (ELPI) for sizing. Different engine operating conditions were selected in order to evaluate their influence on the particle nature and size distribution.

This paper illustrates the results of an experimental investigation on the liquid fuel spray from a multi-jet common rail injection system both under non evaporative and evaporative conditions. Tests have been taken using a 5 hole, 0.13 mm diameter, 150° spray angle, micro-sac nozzle having a flow rate of 270 cm3/30 sec@10 MPa exploring different injection strategies. Experiments have been taken, under non evaporative conditions, injecting the fuel within stagnant inert gas, at different density, in a high-pressure optically-accessible cylindrical vessel with three large quartz windows. Under evaporative conditions, the experiments have been taken within a crank-case scavenged single-cylinder 2-stroke direct injection Diesel engine provided of optical accesses to the combustion chamber. It allows to study the fuel injection process under thermodynamic conditions similar to those currently reached in modern direct injection diesel engines.

The intention of the presented work was to develop a new simulation tool that fits into a CFD (computational fluid dynamics) workflow and provides information about the soot particle size distribution. Additionally it was necessary to improve and use state-of-the-art measurement techniques in order to be able to gain more knowledge about the behavior of the soot particles and to validate the achieved simulation results. The work has been done as a joint research financed by the European Community under FP5.