Search Results

This paper presents the results from experiments and Computational Fluid Dynamics (CFD) simulations performed to understand the impact of piston geometry on ignition delay for Dimethyl Ether (DME)/air mixtures inside a Rapid Compression Machine (RCM). Three piston shapes and two dilution ratios are studied using CFD simulations validated by experiments. The three piston geometries under consideration are: a flat piston, a piston with an enlarged crevice, and a bowl piston. Key phenomena analyzed in the study include fluid flow patterns, heat transfer, temperature homogeneity of the mixture, and ignition delay. The CFD model provides reasonable predictions of ignition delay when compared with experimental data. Simulations indicate that flat and bowl pistons show similar heat transfer, ignition delay, and combustion characteristics, while the enlarged creviced piston shows lower peak temperatures and a cooler mixture core due to higher wall heat transfer.

The nitrogen dioxide (NO₂) emissions of compression ignition diesel engines are usually relatively small, especially when operated at medium and high loads. Recent experimental investigations have suggested that adding hydrogen (H₂) into the intake air of a diesel engine leads to a substantial increase in NO₂ emissions. The increase in NO₂ fraction in the total NOx is more pronounced at lower engine load than at medium- and high-load operation, especially when a small amount of H₂ is added. However, the chemistry causing the increased NO₂ formation in H₂-diesel dual-fuel engines has not been fully explored. In the present work, kinetics of NO and NO₂ formation in a H₂-diesel dual-fuel engine are investigated using a CFD model integrated with a reduced hydrocarbon oxidation chemistry and an oxides of nitrogen (NOx) formation mechanism. A low-load and a medium-load operating condition are selected for numerical simulations.

In the Premixed-Charge Compression Ignition (PCCI) combustion mode, fuel is injected fairly early before top-dead-center (TDC) of compression compared to the conventional near-TDC injection combustion mode. Early fuel injection into a low temperature in-cylinder environment results in long ignition delay and high peak heat release rate. Since the onset of ignition occurs after the end of injection, importance of spray and bowl induced flow field and mixing is not so obvious. In the present work, computational analysis is used to investigate the effects of spray-bowl interactions on PCCI combustion and emissions at a light-load (4Bar BMEP) operation of a medium-duty, direct injection diesel engine. Multidimensional CFD code KIVA-3V coupled with detailed chemical kinetics is used to perform combustion simulations.

Two turbulent combustion modeling approaches, which were large eddy simulations in conjunction with detailed kinetics (LES-CHEMKIN) and Reynolds Averaged Navier Stokes with detailed kinetics (RANS-CHEMKIN), were used to model two partially premixed engine conditions. The results were compared with average pressure and heat release data, as well as images of in-cylinder ignition chemiluminescence and OH radical distributions. Both LES-CHEMKIN and RANS-CHEMKIN match well with experimental average data. However, LES-CHEMKIN has advantages over RANS-CHEMKIN in predicting the details of location of ignition sites, temperature as well as OH radical distributions. Therefore, LES offers more realistic representations of the combustion process. As a further improvement aiming at saving computational cost and accounting for turbulence-chemistry interactions, a flamelet time scale (FTS) combustion model is coupled with CHEMKIN to predict the entire combustion process. In this new approach (i.e.

In previous publications, Singh et al. [1, 2] have shown that direct integration of CFD with a detailed chemistry auto-ignition model (KIVA-CHEMKIN) performs reasonably well for predicting combustion, emissions, and flame structure for stratified diesel engine operation. In this publication, it is shown that the same model fails to predict combustion for partially premixed dual-fuel engines. In general, models that account for chemistry alone, greatly under-predict cylinder pressure. This is shown to be due to the inability of such models to simulate a propagating flame, which is the major source of heat release in partially premixed dual-fuel engines, under certain operating conditions. To extend the range of the existing model, a level-set-based, hybrid, auto-ignition/flame-propagation (KIVA-CHEMKIN-G) model is proposed, validated and applied for both stratified diesel engine and partially premixed dual-fuel engine operation.

Three different approaches for modeling diesel engine combustion are compared against cylinder pressure, NOx emissions, high-speed soot luminosity imaging, and 2-color thermometry data from a heavy-duty DI diesel engine. A characteristic time combustion (KIVA-CTC) model, a representative interactive flamelet (KIVA-RIF) model, and direct integration using detailed chemistry (KIVA-CHEMKIN) were integrated into the same version of the KIVA-3v computer code. In this way, the computer code provides a common platform for comparing various combustion models. Five different engine operating strategies that are representative of several different combustion regimes were explored in the experiments and model simulations. Two of the strategies produce high-temperature combustion with different ignition delays, while the other three use dilution to achieve low-temperature combustion (LTC), with early, late, or multiple injections.

Although in-cylinder optical diagnostics have provided significant understanding of conventional diesel combustion, most alternative combustion strategies have not yet been explored to the same extent. In an effort to build the knowledge base for alternative low-temperature combustion strategies, this paper presents a comparison of three alternative low-temperature combustion strategies to two high-temperature conventional diesel combustion conditions. The baseline conditions, representative of conventional high-temperature diesel combustion, have either a short or a long ignition delay. The other three conditions are representative of some alternative combustion strategies, employing significant charge-gas dilution along with either early or late fuel injection, or a combination of both (double-injection).

The combustion and emissions of a diesel/natural gas dual-fuel engine are studied. Available engine experimental data demonstrates that the dual-fuel configuration provides a potential alternative to diesel engine operation for reducing emissions. The experiments are compared to multi-dimensional model results. The computer code used is based on the KIVA-3V code and consists of updated sub-models to simulate more accurately the fuel spray atomization, auto-ignition, combustion and emissions processes. The model results show that dual-fuel engine combustion and emissions are well predicted by the present multi-dimensional model. Significant reduction in NOx emissions is observed in both the experiments and simulations when natural gas is substituted for diesel fuel. The HC emissions are under predicted by numerical model as the natural gas substitution is increased.