Search Results

Temperature distributions in n-heptane and n-tridecane sprays were measured by the planar laser induced fluorescence (PLIF) method. The spray was formed by injecting fuel into high temperature and high pressure ambient, which was formed by compression of rapid compression and expansion machine (RCEM). In this PLIF method, acetone was used as a fluorescence tracer and was mixed with ambient gas. The fluorescence tracer was excited by 266 nm (the 4th harmonic of a Nd:YAG laser). The fluorescence intensity was measured by an ICCD camera. The temperature and concentration were estimated based on temperature dependency of the fluorescence intensity and the assumption of adiabatic mixing. Based on the measurement results, The difference of mixture distributions in n-heptane and n-tridecane sprays are discussed.

We developed a novel ignition method called laser breakdown-assisted long-distance discharge ignition (LBALDI) that combines laser breakdown with a discharge to realize lean combustion. The creation of laser breakdown plasma between electrodes for discharge enables discharges over longer distances than those of conventional sparkplug as inferred from laser-triggered lightning or laser-triggered gas switches. This method should help realize volumetric ignition through the creation of a long-distance discharge. Experiments on the fundamental discharge and ignition of methane/air mixtures were conducted. The optimum incident time of the laser prior to the application of a high voltage was found to reduce the sparkover voltage and markedly reduce the voltage required by LBALDI under pressurized air conditions. In the ignition experiment, LBALDI showed the fastest heat release rate at the lean flammable limit.

Technology for the enhancement of compression ignition for a natural-gas homogeneous charge compression ignition (HCCI) engine was developed using nonthermal plasma. Specifically, nonthermal plasma was utilized to enhance the ignition of the methane/air premixture by irradiating it in an intake tube. The effect of the irradiation on compression ignition was investigated using a rapid compression and expansion machine; the ignition delay was found to shorten by the influence of irradiation. The dependence of the ignition delay time on the temperature at the end of compression was determined. Chemical analysis of the plasma-processed gas was performed using a gas detection tube as a simple method and ion-attachment ionization mass spectrometry (IAMS) as a novel method. A chemical kinetic simulation was also conducted to examine the temperature dependence of the ignition delay.

As a result of the excavation of unconventional sources of natural gas, which has rich reserves, has attracted attention as a fuel for use in natural gas engines for power generation. From the viewpoints of efficient resource utilization and environmental protection, lean burn is an attractive technique for realizing a higher thermal efficiency with lower NOx emissions. However, ignition systems have to be improved for lean-burn operations. Laser ignition, which is expected to serve as an alternative to spark plug ignition, can decrease the heat loss and has no restriction on the ignition location because of the absence of an electrode. Consequently, an extension of the lean-burn limit by laser ignition has been demonstrated. In this study, we investigated the effects of the location and number of laser ignition points on engine performance and exhaust emissions. Laser ignition was also compared with conventional spark plug ignition.

Dielectric barrier discharge (DBD) was applied to control the pressure-rise rate of homogeneous compression ignition, which is an important obstacle for homogeneous charge combustion engines. DBD can produce nonthermal plasmas and has been generated in air/fuel mixtures to reform some of the fuel molecules found in such mixtures. This generally shortens the ignition delay of compression ignition of the air/fuel premixture. Stratification of the reformed premixture in the combustion chamber was achieved by pulsed DBD irradiation during the induction process. The formation of inhomogeneous distribution of the reformed premixture is expected by the formation of discharge at the end of the intake processes. A demonstrative experiment was conducted by using a rapid compression and expansion machine. A simple plasma reactor was developed and installed at the intake tube. High-voltage, high-frequency pulses were applied to form plasmas. n-Heptane was used as fuel.

Numerical calculations were performed to investigate the mixture formation, ignition, and combustion processes in a diesel spray. The spray was formed by injecting n-heptane into a constant volume vessel under high-temperature and high-pressure conditions. The fuel droplets were described by a discrete droplet model (DDM). Numerical calculations for the flow and turbulent diffusion processes were performed on the basis of large eddy simulation (LES) to describe the processes of local non-homogeneous mixture formation and heat release. The oxidation processes in the mixture were calculated by Schreiber's five-step mechanism for n-heptane. Calculations were performed for sprays formed by single-stage injection and pilot/main two-stage injection. The flame structure in a diesel spray and its temporal change were discussed using a flame index proposed by Yamashita et al.

The methodology of lubricity evaluation for DME fuel was established by special modified HFRR (High-Frequency Reciprocating Rig) such as Multi-Pressure/Temperature HFRR (MPT-HFRR). The obtained results were summarized as follows: The HFRR method is adaptable with DME fuel. There is no effect of the test pressure (up to 1.8 MPa) and the test temperature (up to 100°C) of MPT-HFRR on wear scar diameter. The results with MPT-HFRR can be applied at the sliding parts of the injection needle and the fuel supply pump's plungers which are secured lubricity by the boundary lubrication mode mainly and the mixed lubrication mode partially. Using the fatty-acid-based lubricity improver in amounts of approximately 100 ppm, the lubricity of DME, which has a lack of self-lubricity, is ensured as same as the diesel fuel equivalent level. There is a big deviation of measured wear scar diameter when the LI concentration is not enough.

DME as a fuel for compression ignition (diesel) engines has been actively studied for about ten years due to its characteristically low pollution and reputation as a “smokeless fuel”. During this time, the practical application is taking shape based on necessary tasks such as analysis of injection and combustion, engine performance, and development of experimental vehicles. At this moment, standardization of DME as a fuel was started under ISO in 2007. There are concerns regarding the impurities in DME regarding the mixing during production and distribution as well as their effect on additives for lubricity and odor. In this report, the effect of DME fuel impurities on performance of a DME powered diesel engine was investigated. The platform was a DME engine with common-rail fuel injection and was evaluated under partial load stable mode and Japanese transient mode (JE05) testing parameters.

The tasks to improve diesel emissions and fuel consumption must be accomplished with urgency. However, due to the trade-off relationship between NOx emissions, soot emissions and fuel consumption, clean diesel combustion should be achieved by both innovative combustion and fuel technologies. The objective of this study is to extend the clean diesel combustion operating range (Engine-out emission: NOx ≺ 0.2 g/kWh, Soot ≺ 0.02 g/kWh). In this study, performance of a single-cylinder test engine equipped with a hydraulic valve actuation system and an ultra-high pressure fuel injection system was investigated. Also evaluated, were the effects of fuel properties such as auto-ignitability, volatility and aromatic hydrocarbon components, on combustion performance. The results show that applying a high EGR (Exhaust gas recirculation) rate can significantly reduce NOx emission with an increase in soot emission.

It has been clarified that diesel fuel properties have a great effect on the exhaust emissions and fuel consumption of a conventional diesel combustion regime. And as other diesel combustion regimes are applied in order to improve exhaust emissions and fuel consumption, it can be supposed that the fuel properties also have significant effects. The purpose of this study is to propose the optimum diesel fuel properties for a premixed compression ignition (PCI) combustion regime. In this paper, the effect of the auto-ignitability of diesel fuels on exhaust emissions and fuel consumption was evaluated using a heavy-duty single-cylinder test engine. In all experiments, fuels were injected using an electronically controlled, common-rail diesel fuel injector, and most experiments were conducted under high EGR conditions in order to reduce NOx emissions.

The performance of a medium duty DME truck was evaluated by field tests and engine bench tests. The DME vehicle was given a public license plate on October 2004, after which running tests were continued on public roads and a test course. The DME vehicle could run the whole distance, about 500 km, without refueling. The average diesel equivalent fuel consumption of the fully loaded DME truck was 5.75 km/l, running at 80 km/h on public highways. Remedying several malfunctions that occurred in the power-train subsystems enhanced the vehicle performance and operation. The DME vehicle accumulated 13,000 km as of August, 2006 with no observed durability trouble of the fuel injection pump. Disassembly and inspection of the fuel injectors after 7,700 km operation revealed a few differences in the nozzle tip and the needle compared to diesel fuel operation. However, the injectors were used again after cleanup.

In this study, diesel exhaust emission characteristics were investigated as GTL (Gas To Liquid) fuel was applied to a heavy-duty diesel truck which had been developed to match a Japanese new long-term exhaust emission regulation (NOx < 2.0 g/kWh, PM < 0.027 g/kWh). The results in this study show that although the test vehicle has advanced technologies (e.g. high pressure fuel injection, oxidation catalyst, and urea-SCR aftertreatment system, etc.) which are applied to reduce diesel emissions, the neat GTL fuel has a great advantage to reduce particulate matter emissions and poly aromatic hydrocarbons. And regarding nano-size PM emissions, nuclei mode particles emitted during idling are significantly decreased by using the GTL fuel.

Biodiesel fuel has attracted much attention as a carbon neutral fuel because it is made from vegetable oil. Especially in Southeast Asia, there are numerous biofuel resources, such as palm oil and coconut oil, and it is desirable to utilize these for CO2 reduction. In this paper, we evaluate the properties of biodiesel fuel and biodiesel blended diesel oil. The low temperature performance of palm oil methyl ester (PME) is poor and it affects low temperature performance, even if the PME blending rate is low. The oxidation stability is a very important property of biodiesel fuel because degraded biodiesel fuel produces organic acids and polymeric substances. PME contains mainly saturated fatty acids methyl esters, so the oxidation stability is better than other fats and oils. When containing antioxidants such as beta carotene, biodiesel's oxidation stability is improved.

In this study, measurement methods of aldehydes and volatile organic compounds (VOCs) from off-road engine have been investigated. Also, their emission characteristics have been evaluated. By using high-performance liquid chromatograph (HPLC), aldehydes could be measured with small variation. Major aldehydes from off-road engine are formaldehyde and acetaldehyde. Total aldehydes emission is not necessarily low compared to THC emission. The emission characteristics of aldehydes are similar to that of CO, THC and PM. For VOCs sampling, sampling tube with absorbent was better than sampling bag because some kinds of VOCs tend to become absorbed on the sampling bag. Except for 1,3-butadiene, VOCs could be measured with small variation by using gas chromatography-mass spectrometer (GC-MS). Benzene, toluene and xylene were major species found in VOCs. The emission characteristics of VOCs were also similar to ones of CO, THC and PM.

The Agency of Natural Resources and Energy, Ministry of Economy, Trade and Industry has conducted conformity tests of diesel fuel containing Fatty Acid Methyl Ester (FAME) to amend diesel fuel standards in Japan. The objective of the tests is to examine appropriate specifications of diesel fuel containing FAME for automotive use for existing vehicles in the Japanese market. The conformity testing includes verification of fuel system component compatibility, tail pipe emissions, and characterization of the reliability and durability of the engine system, including the fuel injection system. In designing the conformity tests, the maximum FAME concentration was 5%. Most of the new standards are essentially equivalent to EN14214, but the total acid number (TAN) of specific acids, and oxidation stability of the new standards for diesel fuel containing FAME, are different from EN14214.

Dimethyl ether (DME) has been attracting notable attention as a clean alternative fuel for diesel engines. The authors developed a medium duty DME truck, and investigated aspects of vehicle performance such as engine power, exhaust characteristics, fuel consumption, noise, in-vehicle systems, and so on. Results indicated that higher engine torque and power could be achieved with DME compared to diesel fuel operation of the base engine at any engine speed. Results also showed that emissions decreased dramatically, to 27% for NOx, 74% for HC, 95% for CO and 94% for PM (Particulate Matter) compared to maximum allowed Japanese 2003 emission regulations. The operating noise of the DME vehicle was slightly lower than the base vehicle with diesel fuel, because the combustion noise with DME was decreased compared to with diesel fuel operation. The DME vehicle was given a public license plate in October 2004, after which running test continued on public roads and on a test course.

In this report, trace levels of harmful substances, such as formaldehyde, acetaldehyde, SO2, benzene and so on, emitted from a DME fueled direct injection (DI) compression ignition (CI) engine were measured using a Fourier Transform Infrared (FTIR) emission analyzer. Results showed that the NO portion of NOx emissions with DME exceeded diesel fuel operation levels. DME fueling caused greater amounts of water than with diesel fuel operation. DME fueling was also associated with higher formaldehyde emissions than with diesel fuel operation. However, using an oxidation catalyst, formaldehyde could be decreased to a negligible level.

In this study, a MPT-HFRR (Multi-Pressure/Temperature High-Frequency Reciprocating Rig) was manufactured based on a diesel fuel lubricity test apparatus. The MPT-HFRR was designed to be used for conventional test methods as well as for liquefied gas fuel tests. Lubricity tests performed on a calibration standard sample under both atmospheric pressure and high pressure produced essentially constant values, so it was determined that this apparatus could be used for assessing the lubricity of fuel. Using this apparatus, the improvement of lubricity due to the addition of a DME (Dimethyl Ether) fuel additive was investigated. It was found that when 50ppm or more of a fatty acid lubricity improver was added, the wear scar diameter converged to 400μm or less, and a value close to the measured result for Diesel fuel was obtained. The lubricity obtained was considered to be generally satisfactory.

The engine performance and exhaust characteristics of the DME-powered diesel engine with an injection system developed for DME were investigated. The injection pump is an inline type that can inject double amount of DME fuel compared to the base injection pump because the calorific value of DME is about half lower than that of diesel fuel. The effect of injection timing on engine performances such as thermal efficiency, engine torque, and exhaust characteristics were investigated. Maximum torque and power with DME could be achieved the same or greater level compared to diesel fuel operation. Considering over all engine performances, the best dynamic injection timings without EGR were -3, -3, -6 and -9 deg. ATDC in 1120, 1680, 2240 and 2800 rpm engine speeds respectively in this experiment.

In this study, advantages of GTL fueled DI diesel engine were observed, then, some cautionary areas, notably the aptitude for sealing materials, were investigated. Some advantages of using GTL as a diesel engine fuel include reduction of soot emission levels, power output and fuel consumption with GTL to conventional diesel fuel operation is equivalent, super-low sulfur content of GTL and its liquid state at normal temperature and pressure. However, there are some problems with putting GTL fuel on the market, such as lubricity, aptitude for sealing materials, high cetane index and high pour point. It is necessary to use additives to improve GTL's lubricity, and selecting the most appropriate type of lubricity improver is also important. The influence of GTL on the swelling properties of standard rubber materials seem basically the same, but it is necessary to notice on used rubbers.