Refine Your Search

Date

Date

Topic

Topic

Data management Missiles Snowmobile Technical Committee Vehicle acceleration

Search Results

Viewing 1 to 20 of 32
12Next >Last >>
Sort by published
Standard

Snowmobile Probe Test for Contact with Power Driven Parts
2022-07-08
CURRENT
J2826_202207
This SAE Standard establishes the test equipment, procedure, and acceptance criteria necessary to determine the location of power driven components that could—upon inadvertent contact by an operator, passenger, or bystander—inflict injury.
Standard

Dynamic Cushioning Performance Criteria for Snowmobile Seats
2022-05-02
WIP
J89
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmobile seat system. The document is intended to provide a tool for the development of safer snowmobile seats. It is recognized that the seat is only a portion of the entire vehicle protective suspension system. It is, however, usually required that the seat serve as added protection to the suspension system, since the latter may "bottom out" during a severe impact. The term "seat" refers to the occupant-supporting system not normally considered part of the vehicle suspension or frame system. In some cases, it may include more than the foam cushion.
Standard

Snowmobile Tail (Rear Position) Lamp
2021-06-10
CURRENT
J279_202106
This SAE Standard provides test procedures, performance requirements, design guidelines, and installation guidelines for snowmobile tail (rear position) lamp.
Standard

Brake System Test Procedure - Snowmobiles
2021-03-08
CURRENT
J45_202103
This SAE Recommended Practice establishes a uniform procedure for the level surface testing of hand-operated brake systems on recreational noncompetitive snowmobiles.
Standard

Maximum Exterior Sound Level for Snowmobiles
2021-03-01
CURRENT
J192_202103
This SAE Standard establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles.
Standard

Maximum Exterior Sound Level for Snowmobiles
2020-01-15
HISTORICAL
J192_202001
This SAE standard establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year-round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow-covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
Standard

Snowmobile Passenger Handgrips
2019-07-24
CURRENT
J1062_201907
This SAE Recommended Practice is intended to give information to engineers and designers in order that access to a passenger handgrip, when used, is easily obtained, and that such handgrips offer maximum safety for a person at least as large as a 95th percentile adult male during snowmobile operation.
Standard

Maximum Exterior Sound Level for Snowmobiles
2019-01-23
HISTORICAL
J192_201901
This SAE Recommended Practice establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year-round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow-covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
Standard

Brake System Test Procedure - Snowmobiles
2018-11-14
HISTORICAL
J45_201811
This SAE Recommended Practice establishes a uniform procedure for the level surface testing of hand-operated brake systems on recreational noncompetitive snowmobiles.
Standard

Dynamic Cushioning Performance Criteria for Snowmobile Seats
2018-11-14
CURRENT
J89_201811
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmobile seat system. The document is intended to provide a tool for the development of safer snowmobile seats. It is recognized that the seat is only a portion of the entire vehicle protective suspension system. It is, however, usually required that the seat serve as added protection to the suspension system, since the latter may "bottom out" during a severe impact. The term "seat" refers to the occupant-supporting system not normally considered part of the vehicle suspension or frame system. In some cases, it may include more than the foam cushion.
Standard

Snowmobile Drive Mechanisms
2018-06-12
CURRENT
J1279_201806
This SAE Recommended Practice is applicable to snowmobiles as defined in SAE J33.
Standard

Brake System Test Procedure - Snowmobiles
2016-08-09
HISTORICAL
J45_201608
This SAE Recommended Practice establishes a uniform procedure for the level surface testing of hand-operated brake systems on recreational noncompetitive snowmobiles.
Standard

Snowmobile Probe Test for Contact with Power Driven Parts
2016-02-18
HISTORICAL
J2826_201602
This SAE Recommended Practice establishes the test equipment, procedure, and acceptance criteria necessary to determine the location of power driven components that could, upon inadvertent contact by an operator, passenger, or bystander, inflict injury.
Standard

Measurement of Exhaust Sound Levels of Stationary Snowmobiles
2015-11-24
HISTORICAL
J2567_201511
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
Standard

Dynamic Cushioning Performance Criteria for Snowmobile Seats
2014-04-09
HISTORICAL
J89_201404
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmobile seat system. The document is intended to provide a tool for the development of safer snowmobile seats. It is recognized that the seat is only a portion of the entire vehicle protective suspension system. It is, however, usually required that the seat serve as added protection to the suspension system, since the latter may "bottom out" during a severe impact. The term "seat" refers to the occupant-supporting system not normally considered part of the vehicle suspension or frame system. In some cases, it may include more than the foam cushion.
Standard

Maximum Exterior Sound Level for Snowmobiles
2013-01-10
HISTORICAL
J192_201301
This SAE Recommended Practice establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
12Next >Last >>
X