This SAE Standard provides test procedures, performance requirements, design guidelines, and installation guidelines for snowmobile tail (rear position) lamp.
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment, and promote uniform testing.
This SAE standard establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year-round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow-covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
This SAE Recommended Practice covers standardized basic tests, test methods, and requirements applicable to electromechanical switching devices which may be used on snowmobiles as defined in SAE J33.
This SAE Recommended Practice is intended to give information to engineers and designers in order that access to a passenger handgrip, when used, is easily obtained, and that such handgrips offer maximum safety for a person at least as large as a 95th percentile adult male during snowmobile operation.
This SAE Recommended Practice is intended to provide the minimum acceptable criteria for snowmobile hand throttle control systems. This recommendation is not intended to cover competition vehicles, nor is it intended to limit development of new and/or improved technology in controls. Although these recommendations are primarily addressed to hand-control systems using an outer flexible conduit with a multiple strand inner cable, the basic requirements of freedom of movement, strength, material, etc., will apply to any system.
This SAE Recommended Practice is intended to provide the minimum acceptable criteria for snowmobile hand brake control systems. This recommendation is not intended to cover competition vehicles, nor is it intended to limit development of new and/or improved technology in controls. Although these recommendations are primarily addressed to hand control systems using an outer flexible conduit with a multiple strand inner cable or hydraulic type brake control system, the basic requirements of freedom of movement, strength, material, etc., will apply to any system.
This SAE Recommended Practice establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year-round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow-covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
This recommended practice establishes the instrumentation, test site, and test procedure for determining the exterior operational sound level for snowmobiles.
This SAE Recommended Practice covers standardized basic tests, test methods, and requirements applicable to electromechanical switching devices which may be used on snowmobiles as defined in SAE J33.
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Recommended Practice establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
This SAE Recommended Practice is intended to provide the minimum acceptable criteria for snowmobile hand brake control systems. This recommendation is not intended to cover competition vehicles nor is it intended to limit development of new and/or improved technology in controls. Although these recommendations are primarily addressed to hand control systems using an outer flexible conduit with a multiple strand inner cable or hydraulic type brake control system, the basic requirements of freedom of movement, strength, material, etc., will apply to any system.