Refine Your Search

Date

Date

Topic

Topic

Aircraft Exhaust systems Hydraulic systems Textile and Flexible Plastics Committee Materials properties Assembling Drying Parts and Components

Search Results

Viewing 1 to 20 of 95
123Next >Last >>
Sort by published
Standard

Test Method for Determining Blocking Resistance and Associated Characteristics of Automotive Trim Materials
2023-02-20
CURRENT
J912_202302
This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.
Standard

Seam Damage Test Procedure
2022-09-14
CURRENT
J1531_202209
This procedure is used to determine seam strength and seam fatigue of automotive textiles, vinyl coated fabrics and related soft trim materials.
Standard

Felts - Wool and Part Wool
2022-09-08
CURRENT
J314_202209
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Fiberboard Test Procedure
2022-08-26
CURRENT
J315_202208
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Test for Chip Resistance of Surface Coatings
2022-08-26
CURRENT
J400_202208
This SAE Recommended Practice covers a laboratory procedure for testing and evaluating the resistance of surface coating to chipping by gravel impact. The test is designed to reproduce the effect of gravel or other media striking exposed paint or coated surfaces of an automobile. The specific intent of the test is to evaluate organic surface coatings or systems on flat test panels; however, it may be possible to extend this type of testing to finished parts or other types of materials such as anodized aluminum or plated plastics if the results are interpreted with respect to the limitations and intent implied by the original testing procedures and rating system. This document may involve hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with its use.
Standard

Outdoor Weathering of Exterior Materials
2022-05-18
CURRENT
J1976_202205
This test method specifies the exposure racks, black boxes, and instrumentation, which shall be used for the outdoor weathering of materials for automotive exterior application.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles, and Colored Trim
2021-12-30
CURRENT
J1545_202112
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Test Method for Determining Cold Cracking of Flexible Plastic Materials
2021-09-15
CURRENT
J323_202109
This SAE Recommended Practice is applicable for determining the cold characteristics of flexible plastic materials, as applicable. It consists of three different methods for determining low-temperature properties of materials depending on type of material and end use. The method used shall be as specified by the contractual parties.
Standard

Design Guidelines for Fiberboard Materials
2019-09-25
CURRENT
J1774_201909
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2 General Product Information 3 Design Characteristics 4 Physical/Mechanical Properties 5 Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim
2014-10-27
HISTORICAL
J1545_201410
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
123Next >Last >>
X