Search Results

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE RF CONNECTOR SYSTEMS

2023-07-10

CURRENT

USCAR17-6

This document contains procedures for testing performance of SMB-style electrical terminals, connectors and components for coaxial cable connection systems intended for road vehicle applications. These are often called FAKRA II designs. This specification does not apply to the Non RF portion of a Hybrid RF connection system. The intent of this specification is to qualify sealed and unsealed RF connectors that operate at frequencies from DC to 6 GHz. The characteristic impedance of the SMB/FAKRA connection system is 50 ohms however this specification does not exclude the use of these RF connectors on non-50 ohm cables or systems. This specification does not apply to single conductor wire or twisted pair connection systems. This specification (along with SAE/USCAR 18) is designed to provide the mechanical and electrical data required to insure that assemblies from various manufacturers will perform reliably in actual conditions.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2023-03-23

CURRENT

USCAR44-2

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray, and different thicknesses of the holes that the clip is inserted into.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE ELECTRICAL CONNECTOR SYSTEMS

2022-06-30

CURRENT

USCAR2-8

This specification covers performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in road vehicle applications that are: low voltage (0 to 20 VDC) or Coaxial. Incomplete (mechanical) specifications for jacketed twisted pair connectors are also provided. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems. They are not applicable to Edge Board connector systems, twist-lock connector systems, >20 VAC or DC, or to eyelet terminals. No electrical connector, terminal, or related component may be represented as having met USCAR specifications unless conformance to all applicable requirements of this specification have been verified and documented. All required verification and documentation must be done by the supplier of the part or parts.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE MINIATURE BULBS

2022-03-15

CURRENT

USCAR3-4

The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications. The following tests shall be run whenever the following occurs: New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test. The completion of one calendar year as noted in the following Test Schedule Table. Process control data is acceptable.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE HALOGEN LIGHT SOURCES

2022-03-15

CURRENT

USCAR14-3

The procedures contained in this specification cover the laboratory testing of replaceable halogen incandescent bulbs for use in automotive road illumination. The following tests are intended to be run under the following conditions. New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test The completion of one calendar year, accept as noted in the following Test Schedule Table. Test Title Yearly Physical Dimensions X Mean Spherical Candela (MSCD) X External Visual Examination X Color X Leak/Sealability Through Terminals and Seals X Deflection X Fluid Compatibility Terminal Retention X Resonant Frequencies Aged Resonant Frequency Salt Spray Outgassing Temperatures Requirement Laboratory Life at 14.0 VDC X Luminous Intensity Maintenance X Vibration Durability Shock Aged Vibration Durability Terminal Requirements DRL (SAE J2087)

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE LAMP ASSEMBLIES

2022-03-15

CURRENT

USCAR34

The procedures contained in this specification cover the laboratory testing of Exterior Lamps for use in automotive road illumination. The following tests are intended to be run under the following conditions. This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards. If other manufacture’s components are intended to be approved for use in the lamp assembly, then those possible combinations of components shall be considered a new lamp assembly and shall also be tested.

Standard

SPECIFICATION FOR TESTING GAS DISCHARGE LIGHT SOURCE SUBSYSTEM

2022-03-02

CURRENT

USCAR27-1

This specification is a general level subsystem light source specification that establishes test requirements of a Gas Discharge Light Source (GDLS) subsystem for use on passenger vehicles. The completed test data to this test specification is intended to be provided to the OEM by the Tier one lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved GDLS experiences a design, manufacturing or component change. This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards. The subsystem is defined as the ballast, igniter and light source and shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the test sample shall constitute a failure of the entire sample. Substitution or replacement of only the light source shall be allowed during testing.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2021-01-20

HISTORICAL

USCAR44-1

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray, and different thicknesses of the holes that the clip is inserted into.

Standard

ELECTRICAL CONNECTOR DESIGN REQUIREMENTS

2021-01-20

CURRENT

USCAR12-6

This document gives specific and measurable design requirements to be applied at a design review prior to tooling. The specification is formatted as a checklist to aid in its use. The requirements do not apply in all situations so engineering judgment must be used. This is a specification for design; applicable performance specifications (USCAR-2, etc.) must still be performed. Specific requirements in this document are grouped by component using a prefix as shown in Table 1 and are numbered by an item number following the prefix.

Standard

STANDARD FOR TIRE TRACEABILITY CONTENT AND FORMAT FOR THE RADIO-FREQUENCY IDENTIFICATION (RFID) TAG AND ASSOCIATED TIRE DATA SET

2020-11-19

CURRENT

USCAR39-1

This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an identifier. The standard describes a unique identification and the associated data set for each tire produced by the tire fabricator. This data will either be provided or transmitted at the time of shipment to retailers, wholesalers or original equipment vehicle manufacturers. Tire identification code and data may be used for error proofing, determining the tire specifications or supporting any inquiries that occur for the duration of its automotive life.

Standard

LEAD-FREE SOLDER VALIDATION TEST PLAN

2020-11-19

CURRENT

USCAR40-2

This guideline is applicable to existing lead solder production products that will change to lead-free solder processes to meet the ELV Directive 2000/53/EC Annex II, exemption 8B requirements. This guideline is applicable to similar products used by multiple OEM's that have the same manufacturing processes / equipment. The intent is to streamline the supplier’s environmental testing via common qualification to reduce timing, quantities, and costs.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE LED MODULES

2020-08-03

CURRENT

USCAR33-1

This specification is a general level subsystem light source specification that establishes test requirements of light emitting diode (LED) components and modules for use in automotive lighting systems. The completed test data from this test specification is intended to be provided to the OEM by the Tier 1 lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved LED module experiences a design, manufacturing, or component change. This document shall be applied to systems that meet the requirements for design, performance, and validation established by government standards. The LED module is defined as the LED devices and any electronics required to properly energize the LEDs using a vehicle electrical power system along with any associated electrical wiring, connectors, and thermal management system. Samples shall be tested as a subsystem and considered one test sample for the entire test sequence.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE LIGHT BULB SOCKETS

2020-05-28

CURRENT

USCAR15-4

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connectors, direct wire wedge base sockets, bayonet base sockets with integral connectors, direct wire bayonet base sockets, wedge base and bayonet base sockets with circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendices E and F whenever the following occurs: New design. Design, material, or process change made to an existing device, which could affect the outcome of the test. The test sequences shown in Appendix G shall be run annually.

Standard

STANDARD FOR TIRE TRACEABILITY CONTENT AND FORMAT FOR THE RADIO-FREQUENCY IDENTIFICATION (RFID) TAG AND ASSOCIATED TIRE DATA SET

2019-04-17

HISTORICAL

USCAR39

This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an identifier. The standard describes a unique identification and the associated data set for each tire produced by the tire fabricator. This data will either be provided or transmitted at the time of shipment to retailers, wholesalers or original equipment vehicle manufacturers. Tire identification code and data may be used for error proofing, determining the tire specifications or supporting any inquiries that occur for the duration of its automotive life.

Standard

PERFORMANCE SPECIFICATION FOR WELDED WIRE-TO-WIRE SPLICES

2018-06-14

CURRENT

USCAR45

SAE/USCAR-45 defines test methods and performance requirements for ultrasonically-welded wire-to-wire splices for automotive applications. Face-to-face, butt splice, and center strip configurations per Figure 1 can be tested. The tests defined in this specification subject samples on test to stresses that simulate a lifetime of exposure for a road vehicle. Stresses called out in this specification include thermal shock, temperature/humidity cycling and mechanical stress from different directions.

Standard

ELECTRICAL CONNECTOR DESIGN CRITERIA

2017-08-17

HISTORICAL

USCAR12-5

This document gives specific and measurable design criteria to be applied at a design review prior to tooling. The specification is formatted as a checklist to aid in its use. The requirements do not apply in all situations so engineering judgment must be used. This is a specification for design criteria; applicable performance specifications (USCAR-2, etc.) must still be performed. Items in this document are grouped by component as follows: A Terminals B Secondary Terminal Locks C Connectors D Connector Locks E Secondary Connector Locks (Connector Position Assurance, CPA) F Connector Seals G Serviceability H High Voltage (≥60V) Application Requirements I Drawing and General Requirements

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2017-05-10

HISTORICAL

USCAR44

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises a) from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray and different thicknesses of the holes that the clip is inserted into.

Standard

PERFORMANCE SPECIFICATION FOR ULTRASONICALLY WELDED WIRE TERMINATIONS

2016-04-05

HISTORICAL

USCAR38-1

This specification defines test methods and performance criteria for evaluating ultrasonically welded wire-to-terminal metallurgical bonds. The examples used are specific to the linear weld type of process equipment. USCAR-38 is not applicable for “Splice Welding”. The specification is applicable to wire-on-pad configurations with a typical weld shown in Figure 1. This test specification subjects parts under test to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures called-out in this specification include Thermal Shock, Temperature Humidity Cycling and mechanical abuse. This test specification is intended to evaluate the strength and performance of the interface between wires to an electrical terminal. Validation of the performance of the Terminal is a separate task and can be accomplished using a component validation test such as SAE/USCAR-2, which evaluates whether the entire connection system is acceptable.

Standard

ELECTRICAL CONNECTOR DESIGN CRITERIA

2016-02-12

HISTORICAL

USCAR12-4

This document gives specific and measurable design criteria to be applied at a design review prior to tooling. The specification is formatted as a checklist to aid in its use. The requirements do not apply in all situations so engineering judgment must be used. This is a specification for design criteria; applicable performance specifications (USCAR-2, etc.) must still be performed. Items in this document are grouped by component as follows: A Terminals B Secondary Terminal Locks C Connectors D Connector Locks E Secondary Connector Locks (Connector Position Assurance, CPA) F Connector Seals G Serviceability H High Voltage (≥60V) Application Requirements I Drawing and General Requirements

Standard

Lead-Free Solder Validation Test Plan

2015-04-22

HISTORICAL

USCAR40-1

This guideline is applicable to existing lead solder production products that will change to lead-free solder processes to meet the ELV Directive 2000/53/EC Annex II, exemption 8B requirements. This guideline is applicable to similar products used by multiple OEM's that have the same manufacturing processes / equipment. The intent is to streamline the supplier’s environmental testing via common qualification to reduce timing, quantities, and costs.