Search Results

Abstract Super duplex stainless steel (SDSS) is a type of stainless steel made of chromium (Cr), nickel (Ni), and iron (Fe). In the present work, a 1.6 mm wide thin sheet of SDSS is joined using gas tungsten arc welding (GTAW). The ideal parameter for a bead-on-plate trial is found, and 0.216 kJ/mm of heat input is used for welding. As an outcome of the welding heating cycle and subsequent cooling, a microstructural study revealed coarse microstructure in the heat-affected zone and weld zone. The corrosion rate for welded joints is 9.3% higher than the base metal rate. Following the corrosion test, scanning electron microscope (SEM) analysis revealed that the welded joint’s oxide development generated a larger corrosive attack on the weld surface than the base metal surface. The percentages of chromium (12.5%) and molybdenum (24%) in the welded joints are less than those in the base metal of SDSS, as per energy dispersive X-ray (EDX) analysis.

Abstract TOC

Abstract With the use of the stepped surface of the friction pairs of the stepped bearings (SB) in the high-speed centrifugal pumps, its liquid film thickness is suddenly changed and it was discontinuously distributed in the direction of motion of pump. To ensure the continuity of the liquid film thickness and enhance the lubrication efficiency of the pump, based on the lubrication model of the SB, two other structures of the inclined surfaces [inclined bearings (IB)] and curved surfaces [curved bearings (CB)] used to replace stepped surfaces of the SB are investigated, respectively. Under the same conditions of the minimum thickness of the liquid film and initial dimensions of the sliding friction pairs, the influence of both the thickness ratio (α) of the liquid film and dimension ratio (β) in the direction of motion of SB, IB, and CB on the bearing capacity and friction coefficient of the liquid film are simulated and analyzed, respectively.

Abstract TOC

Abstract At present, it is generally considered in the analysis of the secondary motion of engine piston that the piston skirt–cylinder liner friction pair is fully lubricated in an engine operating cycle. However, in practice, when the piston moves upward, the amount of lubricating oil at the inlet may not ensure that the friction pair is fully lubricated. In this article, the secondary motion of piston is studied when the transport of lubricating oil is considered to determine the lubrication condition of piston skirt–cylinder liner friction pair. The secondary motion of piston is solved based on the combined piston motion model, hydrodynamic lubrication model, asperity contact model, and lubricating oil flow model. The secondary motion equation of piston is solved by the Broyden method. The hydrodynamic lubrication equation is solved by the finite difference method. The asperity contact between piston skirt and cylinder liner is calculated by the Greenwood model.

Abstract This study investigated the influence of high-strength low-alloy steel on the fatigue life of a load-bearing member with a non-load-bearing transverse welded attachment (T-joint). It compared high cycle fatigue data to two fatigue design codes, namely BS 7608 and Eurocode EN 1993-1-9. Different base and filler material combinations of varying material strengths were investigated, resulting in a total of three different specimen configurations. Two material combinations had a high-strength steel (Strenx® 700 MC D) for the base material, with one combination having a matched filler material and the other having an undermatched filler material. The third material combination had a lower-strength steel (S 355 JR AR) for the base material, with a matched filler material. Tensile tests were performed to confirm the base material mechanical properties and weld quality of the manufactured specimens.

Abstract In this article, the effect of heat treatment on the microstructure and mechanical behavior of medium-carbon steel wire intended for the spring mattress is investigated using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction, Vickers hardness (Hv), and tensile strength. The results indicate that the microstructure elongation along the wire axis is observed with the bending and kinking lamellae at the deformation level of 57.81%, this change appears as a fracture in the microstructure and leads to an increase in hardness, tensile strength, and intensities of diffraction patterns. After heat treatment, we observed a redistribution in the grain, which is almost the same in the wire rod and drawn wires; indeed, this led to a decrease in hardness, tensile strength, and augmentation in intensities of peaks. The EBSD pole figures reveal the development of texture in the cementite slip plane (001).

Abstract The ASTM D130 was first issued in 1922 as a tentative standard for the detection of corrosive sulfur in gasoline. A clean copper strip was immersed in a sample of gasoline for three hours at 50°C with any corrosion or discoloration taken to indicate the presence of corrosive sulfur. Since that time, the method has undergone many revisions and has been applied to many petroleum products. Today, the ASTM D130 standard is the leading method used to determine the corrosiveness of various fuels, lubricants, and other hydrocarbon-based solutions to copper. The end-of-test strips are ranked using the ASTM Copper Strip Corrosion Standard Adjunct, a colored reproduction of copper strips characteristic of various degrees of sulfur-induced tarnish and corrosion, first introduced in 1954. This pragmatic approach to assessing potential corrosion concerns with copper hardware has served various industries well for a century.

Abstract Due to the incoming phase out of fossil fuels from the market in order to reduce the carbon footprint of the automotive sector, hydrogen-fueled engines are candidate mid-term solution. Thanks to its properties, hydrogen promotes flames that poorly suffer from the quenching effects toward the engine walls. Thus, emphasis must be posed on the heat-up of the oil layer that wets the cylinder liner in hydrogen-fueled engines. It is known that motor oils are complex mixtures of a number of mainly heavy hydrocarbons (HCs); however, their composition is not known a priori. Simulation tools that can support the early development steps of those engines must be provided with oil composition and properties at operation-like conditions. The authors propose a statistical inference-based optimization approach for identifying oil surrogate multicomponent mixtures. The algorithm is implemented in Python and relies on the Bayesian optimization technique.

Abstract Lubrication has been a major area of interest in engineering. Especially in vehicle transmissions, lubrication plays a very crucial role because gears and bearings are constantly subjected to heavy loads. Proper lubrication is essential for maintaining system performance and ensuring endurance life. Insufficient lubrication can lead to excessive wear, increased friction, and eventually, failures in the transmission components. However, excess lubrication can result in power losses due to the resistance offered by the excessive lubricant. Therefore, achieving effective lubrication using optimized lubrication system design is vital for ensuring the longevity and efficiency of the transmission system. Majorly, two types of lubrication methods are used in transmissions: splash lubrication and forced lubrication. This article focuses on forced lubrication, where the lubrication system actively delivers the required flow of lubricant to specific locations within the transmission.

Abstract Assessing the functional quality of an engine lubricant through real-time sensing could pave the way for development of comprehensive engine health monitoring systems. In this study, a permittivity-based, commercial off-the-shelf (COTS) oil quality sensor was implemented in the lubricant flow of a diesel engine after detailed evaluation on a benchtop test facility. The sensor was mounted on the oil filter housing of the engine in the post-filter oil flow, and its implementation required no modifications to the engine block. Simultaneously, the lubricant flow was visualized by incorporating a novel test cell in the oil flow path. Both the sensor assembly and the flow visualization cell were fully characterized on the benchtop facility prior to implementation on the engine.

Abstract The shot-to-shot variations in common rail injection systems are primarily caused by pressure wave oscillations in the rail, pipes, and injector body. These oscillations are influenced by fuel physical properties, injector needle movement, and pressure and suction control valve activations. The pressure waves are generated by pump actuation and injector needle movement, and their frequency and amplitude are determined by fluid properties and flow path geometry. These variations can result in cycle-to-cycle engine fluctuations. In multi-injection and split-injection strategies, the pressure oscillation from the first shot can impact the hydraulic characteristics of subsequent shots, resulting in variations in injection rate and amount. This is particularly significant when using alternative fuels such as biodiesel, which aim to reduce emissions while maintaining fuel atomization quality.

Abstract A rapid compression and expansion machine (RCEM) was used to experimentally investigate the ignition phenomena of dielectric-barrier discharge (DBD) in engine conditions. The effect of elevated pressure and temperature on ignition phenomena of a methane/air premixed mixture was investigated using a DBD igniter. The equivalence ratio was changed to elucidate the impact of DBD on flame kernel development. High-speed imaging of natural light and OH* chemiluminescence enabled visualization of discharges and flame kernel. According to experimental findings, the discharges become concentrated and the intensity increases as the pressure and temperature rise. Under different equivalence ratios, the spark ignition (SI) system has a shorter flame development time (FDT) as compared with the DBD ignition system.

Abstract Lubricant additives are the main means to improve the performance of lubricants. In this article, green and inexpensive layered kaolin were selected as lubricant additives, and the effects of the type of modifier, concentration, particle size of kaolin additives, and working temperatures on the tribological performance of lubricants were investigated. The results showed that the Span80 modifier can effectively improve the dispersibility and friction reduction effects of kaolin oil samples. Compared with kaolin oil samples without the modifier, the modified kaolin oil can reduce the friction coefficient by 40.9% and the wear spot diameter of the steel balls by 43.8%. The layered kaolin additive can significantly reduce the friction coefficient and wear of steel balls in lubrication, and the friction coefficient showed a trend of decreasing and then increasing with increasing kaolin additive concentration and particle size.

Abstract Prediction of the surface finish of hardened bearing steels was estimated in machining with ceramic uncoated cutting tools under various process parameters using two statistical approaches. A second-order (quadratic) regression model (MQR, multiple quantile regression) for the surface finish was developed and then compared with the artificial neural network (ANN) method based on the coefficient determination (R 2), root mean square error (RMSE), and percentage error (PE). The experimental results exhibited that cutting speed was the dominant parameter, but feed rate and depth of cut were insignificant in terms of the Pareto chart and analysis of variance (ANOVA). The optimum surface finish in machining bearing steel was achieved at 100 m/min speed, 0.1 mm/revolution (rev) feed rate, and 0.6 mm depth of cut.

Abstract The present investigation has been conducted to study the tribological and adhesion properties of X10CrNi18-8 austenitic stainless steel (ASTM 301) coatings deposited on aluminum alloys such as AU4G by using the arc-spraying process. These coatings were made with and without a bond-coat layer, which is constituted by NiAl. The structure of the phases that are present in coatings was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The measurements of microhardness and tribological behavior at different loads were also performed on the surface of the coatings. Adherence test was also carried out using four-point bending tests. The SEM showed that the dense microstructures of coatings have a homogeneous lamellar morphology with the presence of porosities and unmelted particles. The main phase of coating corresponds to a solid solution as a face-centered cubic (fcc).

Abstract Hybrid electric vehicles (xHEV) are a critical enabler to fulfil the most recent CO2 and fuel economy requirements in key markets like North America, China, and Europe [1, 2]. Different levels of hybridization exist; the main differentiator is the power of the electric system and battery capacity. Increased electrical power enables the vehicle to run more often in electric mode and recuperate energy from braking, which enhances the saving potential [3]. Mild (MHEV) and plug-in hybrid vehicles (PHEV) impose different duty cycles on the engine compared to a conventional powertrain, potentially altering the degradation mechanisms of the lubricant, and challenging the basis on which the lubricant should be condemned [4]. The biggest concerns are water and fuel dilution [5], which promote corrosion and can form emulsions [6].

Abstract With the introduction of advanced lightweight materials with complex microstructures and behaviors, more focus is put on the accurate determination of their forming limits, and that can only be possible through experiments as the conventional theoretical models for the forming limit curve (FLC) prediction fail to perform. Despite that, CAE engineers, designers, and toolmakers still rely heavily on theoretical models due to the steep costs associated with formability testing, including mechanical setup, a large number of tests, and the cost of a stereo digital image correlation (DIC) system. The international standard ISO 12004-2:2021 recommends using a stereo DIC system for formability testing since two-dimensional (2D) DIC systems are considered incapable of producing reliable strains due to errors associated with out-of-plane motion and deformation.

Abstract To understand how the composition of novel lubricant additives and their ash interact with gasoline particulate filters (GPFs), an accelerated aging protocol was conducted using three lubricant additive formulations and two GPF types. The additive packages (adpaks) consisted of Ca+Mg detergent in a 3:1 or 0:1 ratio and an anti-wear component—either zinc dialkyl dithiophosphate (ZDDP) or a novel phosphonium-phosphinate ionic liquid (IL) substitute. The particulate sampling captured amount/compositions of particulate matter (PM) generated, total particulate number, and size distribution. Five ash loadings were completed. GPF position and adpak composition affected the backpressure, ash composition, ash morphology, and captured mass. The particulate sampling indicated that the ash component consisted primarily of particles less than 50 nm in size and that the Mg-only adpak resulted in more particulate of 50–400 nm in size.

Abstract Personal watercraft (PWC) users and other high-speed watersports participants have sustained rectal and vaginal injuries during falls into the water, herein referred to as water intrusion injuries (WIIs). WIIs result from the rapid introduction of water into these lower body cavities causing injury to the soft tissues of the perineum, rectum, and vagina. While case studies of injured water-skiers and PWC users are reported in the literature, there is little information related to passenger kinematics and pressure exposure during a rearward fall from a PWC. The results of an experimental study of passenger falls from two “high-performance” PWC are presented herein. A human passenger was caused to fall rearward as the PWC was accelerated at maximum throttle starting from idle speed (≈3–4 mph) and planing speeds of ≈20–30 mph. The subject passenger fell from the aft seat position and while standing on the rear platform.