Refine Your Search

Search Results

Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2019-11-12
WIP
J429
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Protective Coatings for Fasteners

2019-10-07
CURRENT
J1648_201910
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard

Metric Thread Rolling Screws

2018-08-20
WIP
J1237
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Torque-Tension Tightening for Metric Series Fasteners

2017-11-08
CURRENT
J1701M_201711
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers a number of the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of tightening tools or equipment used. Also described in this document is the torque management required to achieve satisfactory fastened joint tightening. This guide is limited in application to clearance fit threads, such as the common 6g/6H class of fit. Other thread types including interference fit, mechanical locking, prevailing torque, or forms other than ISO-Metric may apply to some aspects of this standard but are not specifically covered.
Standard

Metric Thread Rolling Screws

2017-09-07
CURRENT
J1237_201709
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2017-01-03
CURRENT
J174M_201701
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

Spring Nuts

2016-11-28
CURRENT
J891_201611
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard

Guide for Rivet Selection and Design Consideration

2016-11-23
CURRENT
J492_201611
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21
CURRENT
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2016-11-18
CURRENT
J1053M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.
Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2016-11-18
CURRENT
J1053_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18
CURRENT
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Steel Self-Drilling Tapping Screws

2014-09-09
WIP
J78
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2014-05-07
CURRENT
J429_201405
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2013-04-29
HISTORICAL
J429_201304
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Spring Nuts

2013-04-16
HISTORICAL
J891_201304
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard

Guide for Rivet Selection and Design Consideration

2013-04-16
HISTORICAL
J492_201304
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
Standard

Blind Rivets - Break Mandrel Type

2013-04-15
HISTORICAL
J1200_201304
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
X