Search Results

This document covers the process to be applied to design characteristics (as defined in AS9102), parts or inspection processes as defined by the purchaser. Design characteristics not included within the scope include electronic, electromechanical or mechanical systems where alternative means of acceptance are approved such as through acceptance test procedures (ATPs). This document does not define processes for identifying or communicating the classification of the parts or design characteristics. This document does not define the procedure to qualify a supplier to undertake these requirements. It is expected that each purchaser will have a procedure to manage the flow-down of these requirements. This document applies to suppliers that demonstrate adequate proficiency in applicable process control methods as determined by the purchaser.

This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance).

This standard establishes requirements for Process Control Methods to sustain product conformity. This includes training, selection of control methods, analysis and improvement of their effectiveness, and subsequent monitoring and control. It applies to all controls documented in the Control Plan. This will include but is not limited to Key Characteristics (KCs) and Critical Items (CIs). This standard aligns and collaborates with the requirements of AS9100, AS9103, AS9145, AS13000, AS13002, AS13003, and AS13004. Commercial-Off-The-Shelf (COTS) items and Standard Catalogue Items (that neither the customer nor supplier hold design authority for) are not included.

The supplier shall use the following process to respond to a customer request for corrective and preventive action.

This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.

This standard establishes supplemental requirements for 9100 and 9145 and applies to any organization receiving it as part of a Purchase Order or other contractual document from a customer. AS13100 also provides details of the Reference Materials (RM13xxx) developed by the SAE G-22 AESQ committee and listed in Section 2 - Applicable Documents, that can also be used by organizations in conjunction with this standard.

This standard establishes requirements for Process Control Methods to sustain product conformity. This includes training, selection of control methods, analysis and improvement of their effectiveness, and subsequent monitoring and control. It applies to all controls documented in the Control Plan. This will include but is not limited to Key Characteristics (KCs) and Critical Items (CIs). This standard aligns and collaborates with the requirements of AS9100, AS9103, AS9145, AS13000, AS13002, AS13003, and AS13004. Commercial-Off-The-Shelf (COTS) items and Standard Catalogue Items (that neither the customer nor supplier hold design authority for) are not included.

This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.

This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.

This document covers the process to be applied to design characteristics (as defined in AS9102), parts or inspection processes as defined by the purchaser. Design characteristics not included within the scope include electronic, electromechanical or mechanical systems where alternative means of acceptance are approved such as through acceptance test procedures (ATPs). This document does not define processes for identifying or communicating the classification of the parts or design characteristics. This document does not define the procedure to qualify a supplier to undertake these requirements. It is expected that each purchaser will have a procedure to manage the flow-down of these requirements. This document applies to suppliers that demonstrate adequate proficiency in applicable process control methods as determined by the purchaser.

This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance).

The standard applies to aero engine suppliers operating a self-release process as a delegated activity from the delegating organization. While primarily developed around the aero engine supply chain requirements, this standard can also be used in other industry sectors where a self-release process may be of benefit.

Le fournisseur devra utiliser le processus qui suit pour répondre à une demande du client d’action corrective et préventive.

The supplier shall use the following process to respond to a customer request for corrective and preventive action.