Search Results

SAE J115 specifies the relevant ISO standards for application to safety labels for use on off-road work machines as defined in SAE J1116.

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

This SAE Standard establishes the maximum gradient rating during hopper discharge of self-propelled, driver-operated sweepers and scrubbers as defined by SAE J2130-1 and SAE J2130-2.

SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to off-road self-propelled work machines as defined in SAE J1116 and tractors and machinery for agriculture and forestry as defined in ANSI/ASAE S390.

This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.

This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting, clamshell, dragline, magnet, pile driver, or similar service.

This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of “sweepings” into a collection hopper.

This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.

This SAE information report covers the basic guidelines concerning off-road tire conditions that warrant replacement, removal, or repair. This material can assist the tire user in establishing specific written procedures for each job site.

This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: a. Tracking Transmitter b. Tracking Receiver c. Telemetry Device d. Remote Display This type of tracking equipment is typically used with Horizontal Earthboring Machines as defined in SAE J2022. The purpose of this document is to define common terms and commercial specifications associated with tracking equipment used in the horizontal earthboring industry.

This SAE Information Report provides general information for installing and tightening fluid conductors and connectors. Following these guidelines, with the consistent proper use of torque wrenches, tightening procedures, and correct torque levels, will result in diminishing leaks and improving service life by avoiding hose twisting, tube binding, false torque, and improper joint closures. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, this report should not be used as a “standard” nor a “specification,” and the values shown should not be construed as “guaranteed” minimums, maximums, or absolutes. This document is an information report to help users by gathering available information from the various connector standards and publishing the information in one source for easy retrieval and applied common usage. This SAE Information Report is primarily intended for mobile/stationary industrial equipment applications.

This SAE Standard provides a comprehensive list of guidelines for the selection, identification, and control of metric- and inch-sized fasteners for use in shipboard applications for both shipbuilder installed joints and for use in shipboard components. This guidance includes the following: a Fastener material selection. b Fastener thread form and fit selection. c Selection of fastener finish, when needed. d Selection of locking devices and elements, when needed. e Selection of screw thread fastener inserts, when needed. f Use of fastener part or identifying numbers. g Identification marking requirements.

This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as filter combinations, is to be agreed upon by contractual parties.

This SAE Surface Vehicle Recommended Practice applies to cranes when used in lifting crane service which are equipped with rope drum rotation indicating devices.

The purpose of this SAE Standard is to specify the procedure for measuring the bank angle of motorcycles.

This SAE Recommended Practice establishes minimum performance requirements for new pneumatic valves when tested in accordance with the test procedure outlined in SAE J1409. The performance requirements will include: a Input-output performance b Leakage characteristics c Low temperature performance d Elevated temperature performance e Corrosion resistance performance f Endurance testing g Structural integrity

This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets; as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, relays, disk drives, LCD matrices, VME circuit cards, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively). An example at this end of the spectrum is a VME circuit card assembly.

This SAE Standard provides a method to obtain consistent force-deflection data of finished (or unfinished, when specified) cushioned components of seats for off-road work machines as listed in SAE J1116. This data may be helpful in maintaining seat comfort characteristics and quality control. There is no intent to establish any acceptance criteria.

Access mechanisms to system data and/or control is a primary use case of the hardware protected security environment (hardware protected security environment) during different uses and stages of the system. The hardware protected security environment acts as a gatekeeper for these use cases and not necessarily as the executor of the function. This section is a generalization of such use cases in an attempt to extract common requirements for the hardware protected security environment that enable it to be a gatekeeper. Examples are: Creating a new key fob Re-flashing ECU firmware Reading/exporting PII out of the ECU Using a subscription-based feature Performing some service on an ECU Transferring ownership of the vehicle Some of these examples are discussed later in this section and some have detailed sections of their own. This list is by no means comprehensive.

The following list consists of hose data provided as of December, 2019, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table, Table 1) along with the test results.