Refine Your Search

Date

Date

Topic

Topic

Author

Author

Nickel Lubricating oils Standard Forming Conductivity Logistics Commercial Vehicle Automotive

Search Results

Viewing 1 to 20 of 1041
123Next >Last >>
Sort by published
Standard

Engine and Transmission Identification Numbers
2024-03-18
CURRENT
J129_202403
This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853.
Standard

Standard Sheet Steel Thickness and Tolerances
2024-03-04
CURRENT
J1058_202403
This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods for specifying thickness tolerances.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus
2024-02-23
CURRENT
J2412_202402
This test method specifies the operating procedures for a controlled-irradiance, xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test duration, as well as any exceptions to the specimen preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as the use of optical filter combinations, is to be agreed upon by contractual parties.
Standard

Safety Labels of Off-Road Work Machines
2024-01-16
CURRENT
J115_202401
SAE J115 specifies the relevant ISO standards for application to safety labels for use on off-road work machines as defined in SAE J1116.
Standard

Fuel Filter - Initial Single-Pass Efficiency Test Method
2023-12-13
CURRENT
J1985_202312
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensure that the particle retention ability of the filter is measured in a single pass, as no appreciable loading or regression will occur.
Standard

Ignition Cable Assemblies
2023-10-20
CURRENT
J2032_202310
This SAE Standard specifies the general requirements and test methods for non-shielded, high-voltage ignition cable assemblies.
Standard

GAD23AC Weld Wire Cut Length
2023-08-31
WIP
GAD23AC
Creation of standardized wording for the cut length of weld wire provides standard lengths based on industry equipment and to allow other lengths as specified by the purchaser as requested
Standard

Sealed Trailer Tow Connector
2023-07-19
CURRENT
J3008_202307
This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control.
Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE RF CONNECTOR SYSTEMS
2023-07-10
CURRENT
USCAR17-6
This document contains procedures for testing performance of SMB-style electrical terminals, connectors and components for coaxial cable connection systems intended for road vehicle applications. These are often called FAKRA II designs. This specification does not apply to the Non RF portion of a Hybrid RF connection system. The intent of this specification is to qualify sealed and unsealed RF connectors that operate at frequencies from DC to 6 GHz. The characteristic impedance of the SMB/FAKRA connection system is 50 ohms however this specification does not exclude the use of these RF connectors on non-50 ohm cables or systems. This specification does not apply to single conductor wire or twisted pair connection systems. This specification (along with SAE/USCAR 18) is designed to provide the mechanical and electrical data required to insure that assemblies from various manufacturers will perform reliably in actual conditions.
Standard

Cast Shot and Grit Size Specifications for Cleaning and Peening
2023-06-27
CURRENT
J444_202306
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
Standard

Thermoset Elastomer Specification System
2023-06-02
CURRENT
J2884_202306
This document provides a method/procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use, recycled, or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum percent, must be specified using a “Z” suffix. This classification system covers thermoset High Consistency Elastomers (HCEs) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F2468.
Standard

Electroplating and Related Finishes
2023-05-22
CURRENT
J474_202305
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layers of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc.
Standard

Standard Reference Elastomers (SREs) for Characterizing the Effect of Liquids on Vulcanized Rubbers
2023-05-10
CURRENT
J2643_202305
This SAE Standard specifies requirements for vulcanized rubbers in sheet form for use as standards in characterizing the effect of test liquids and service fluids. The appendices contain the standard reference elastomer formulas. The property changes of the SRE in contact with the indicated fluid under specified test conditions are the responsibility of the user. See 7.3 and Table 1. This standard is not designed to provide formulations of elastomeric product compositions for actual service.
Standard

Engine Oil Tests
2023-03-08
CURRENT
J304_202303
The purpose of this SAE Information Report is to describe test conditions and performance evaluation factors for both diesel and gasoline engine tests. Specifically, the tests described in this document are used to measure the engine performance requirements for engine oils described by the API Service Categories described in API Publication 1509, ASTM D4485, SAE J183, and SAE J1423 standards, U.S. military specifications, and ILSAC GF Standards.
Standard

Classification System for Thermoplastic Elastomers
2023-03-01
CURRENT
J2558_202303
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. In all cases where provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. This classification is based on SI units.
Standard

Lithium-Ion Cell Performance Testing
2023-01-13
CURRENT
J3220_202301
This SAE Recommended Practice defines performance and life cycle tests for lithium-ion cells used primarily for propulsion of electric vehicles including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), and other similar propulsion applications (for example, forklift trucks). The objective of this document is to define common performance test procedures for lithium-ion cells. Results from these procedures can be used for comparative purposes. Performance requirements are not defined in this document, but are to be defined by the users of the document.
123Next >Last >>
X