Search Results

This specification covers a titanium alloy in the form of welding wire (see 8.5).

This SAE Aerospace Recommended Practice (ARP) establishes methods for testing airframe plain bearings. The purpose of ARP5448 and its associated slash sheets is to document test methods commonly used to evaluate airframe bearings. These test methods may be referenced in specifications, part standards, purchase orders, etc., when the test is deemed appropriate to the intended use of the bearing by the end user of the bearing. These test methods are not intended to encompass every conceivable requirement for an airframe bearing. The end user of the bearing must exercise engineering judgment to determine the most appropriate standard and/or nonstandard tests for the application.

This SAE Recommended Practice is applicable to two- or three-wheel motorcycles intended for highway use. Unless noted, requirements apply to both metallic and nonmetallic tanks. Accessory or aftermarket tanks as well as original equipment tanks are covered.

This test method describes a standardized process to evaluate an aviation lubricant’s resistance to thermal degradation and to evaluate the fluid’s tendency to corrode a steel specimen. Fluids are evaluated in an environment free of both air and moisture at a specified temperature and for a specified time period.

The test method describes the procedure for determination of the total acid number (TAN) of new and degraded polyol ester and diester-based gas turbine lubricants by the potentiometric titration technique. The method was validated to cover an acidity range of 0.05 to 6.0 mg KOH g-1. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricants.

This SAE Aerospace Recommended Practice (ARP) provides the technical terms and nomenclature, together with their definitions and abbreviations/acronyms that are used in aerospace fluid power, actuation and control systems. NOTE: ARP490 and ARP4493 are sources for definitions specifically for electrohydraulic servovalves.

This AIR provides a detailed example of the aircraft and systems development for a function of a hypothetical S18 aircraft. In order to present a clear picture, an aircraft function was broken down into a single system. A function was chosen which had sufficient complexity to allow use of all the methodologies, yet was simple enough to present a clear picture of the flow through the process. This function/system was analyzed using the methods and tools described in ARP4754A/ED-79A. The aircraft level function is “Decelerate Aircraft On Ground” and the system is the braking system. The interaction of the braking system functions with the aircraft are identified with the relative importance based on implied aircraft interactions and system availabilities at the aircraft level. This example does not include validation and verification of the aircraft level hazards and interactions with the braking system.

This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and appropriate inhibitors, for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).

This SAE Standard defines the limits for a classification of automotive gear lubricants in rheological terms only. Other lubricant characteristics are not considered.

The J2012 Digital Annex of Diagnostic Trouble Code Definitions Spreadsheet provides DTC information in an excel format for use in your organization's work processes. The column headings include the same information as contained in the J2012 standard. Information in the excel spreadsheet will be updated several times annually and the spreadsheet includes a column heading denoting which DTCs have been updated in the current version.

This AIR is limited to the requirements of AS50881 and examines these requirements, providing rationale behind them. AS50881 is only applicable to the aircraft EWIS. Pods and other devices that can be attached to an aircraft are considered as part of the aircraft equipment design. Its scope does not include wiring inside of airborne electronic equipment but does apply to wiring externally attached to such equipment. The AS50881 scope does not include attached devices but does include the interface between the pod/equipment and aircraft wiring. Section 3.3.5 addresses components such as antennas and other similar equipment that were once supplied as Government Furnished Aeronautical/Aerospace Equipment (GFAE).

This document establishes a procedure for disposition of landing gear components that have been involved in accidents/incidents. The recommendations in this document apply to components made of ferrous and non-ferrous alloys. The recommendations in this document do not apply to components made of non metallic composite materials.

There is no ISO standard equivalent to this SAE Standard. This SAE Standard identifies and defines the most commonly used terms for piston ring-groove characteristics, specifies dimensioning for groove widths, and demonstrates the methodology for calculation of piston groove root diameter. The requirements of this document apply to pistons and rings of reciprocating internal combustion engines and compressors working under analogous conditions, up to and including 200 mm diameter and 4.5 mm width for compression rings and 8.0 mm width for oil rings. The specifications in this document assume that components are measured at an ambient temperature of 20 °C (68 °F). Tolerances specified in this document represent practical functional limits and do not imply process capabilities.

This procurement specification covers inserts made from A286 alloy of the type identified under the Unified Numbering System as UNS S66286, solid film lubricated with a piastic self locking device, integrated locking keys to positively secure the insert against rotation when properly installed in threaded holes.

This SAE Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power steering system provided as original equipment on personally licensed vehicles. These modifications are generically called “modified effort steering” or “reduced effort power steering.” The purpose of the modification is to alter the amount of driver effort required to steer the vehicle. Retention of reliability, ease of use for physically disabled drivers and maintainability are of primary concern. As an Information Report, the numerical values for performance measurements presented in this report and in the test procedure in the appendices, while based upon the best knowledge available at the time, have not been validated.

NO SCOPE IS AVAILABLE.

This Aerospace Standard establishes the diameter-pitch combinations of ISO metric 60° screw threads recommended for use in the aerospace industry for metric module bolts and nuts.

Scope is unavailable.