Refine Your Search

Topic

Author

Search Results

Standard

Crew Station Lighting - Commercial Aircraft

2019-10-18
CURRENT
ARP1161B
This SAE Aerospace Recommended Practice covers the recommended requirements for the lighting and characteristics of instruments; information plates and displays, emergency, cautionary, advisory and status displays; circuit breaker and toggle switch positions; and the recommended requirements for the utility lighting system.
Standard

Metallic Whiskers

2019-10-17
CURRENT
AIR4129A
This AIR presents an abbreviated review of the metallurgical phenomena known as whiskers. It is not all encompassing; rather, it is intended to introduce the design engineer to the technical issues of metallic whiskers, their formation, and the potentially dangerous problems they can cause.
Standard

Primer, Anodic Electrodeposition for Aircraft Applications

2019-10-17
CURRENT
AMS3144A
This specification establishes the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus

2019-10-17
CURRENT
J1671_201910
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Parking Brake Drawbar Pull Test Procedure - Truck and Bus

2019-10-17
CURRENT
J1729_201910
This SAE Recommended Practice provides a test method and instructions for measuring performance of parking brakes on air- or hydraulic-braked vehicles equipped with in-wheel or drive-line parking brakes. This procedure applies to truck tractors, trailers, trucks, and buses.
Standard

Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated

2019-10-17
CURRENT
AMS4173G
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing. These extrusions have been used typically for parts requiring moderate strength and where distortion during machining must be minimized, but usage is not limited to such applications.
Standard

Vehicle Lift Points for Service Garage Lifting

2019-10-16
CURRENT
J2184_201910
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
Standard

Eddy Current Inspection of Circular Holes in Nonferrous Metallic Aircraft Engine Hardware

2019-10-14
CURRENT
AS4787A
This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.
Standard

Aerospace-Solenoid Valve, Hydraulic, Three Way, Two Position, Direct Acting

2019-10-10
WIP
ARP4945B
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to aid in the specifying and testing of direct acting three way, two position, single and multiple coil, normally open and normally closed solenoid valves used for the pilot actuation of hydraulic control systems and the control of hydraulic components. The information presented should be useful in standardizing terminology, in specifying requirements and performance parameters, and in defining test methods. The recommendations do not restrict or attempt to define the internal design features of solenoid valves. Standard mechanical, electrical and fluid porting interfaces are recommended to provide commonalty, interchangeability, design flexibility and to be more affordable. In general, this recommended practice is directed toward solenoid valves for use in military and commercial flight control and hydraulic actuation systems.
Standard

Degradation Limits of Hydrocarbon-Based Hydraulic Fluids, MIL-PRF-5606, MIL-PRF-83282, and MIL-PRF-87257 Used in Hydraulic Test Stands

2019-10-10
WIP
AIR810E
This SAE Aerospace Information Report (AIR) presents data on normally accepted changes in physical properties and contamination levels for military hydraulic fluids used in hydraulic test stands. This information is of importance to all users of hydraulic test stands to assure the performance data obtained on these test stands for specific components will not be adversely affected by excessive changes in fluid properties or contamination levels. The data pertains to fluids conforming to specifications MIL-PRF-5606, MIL-PRF-83282, and MIL-PRF-87257. The guidelines incorporated in the AIR are the general consensus values of knowledgeable professionals. However, the experience and judgment of engineers and operators responsible for the equipment must be relied upon to determine when the hydraulic fluid is to be replaced.
Standard

Radiator Caps and Filler Necks

2019-10-09
WIP
J164

This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.

Standard

Engine Oil Viscosity Classification

2019-10-09
WIP
J300
This SAE Standard defines the limits for a classification of engine lubricating oils in rheological terms only. Other oil characteristics are not considered or included.
X