Refine Your Search

Topic

Author

Search Results

Standard

Recommended Practice for Performance Rating of Electric Vehicle Battery Modules

2019-11-13
CURRENT
J1798_201911
This SAE Recommended Practice provides for common test and verification methods to determine Electric Vehicle battery module performance. The document creates the necessary performance standards to determine (a) what the basic performance of EV battery modules is; and (b) whether battery modules meet minimum performance specification established by vehicle manufacturers or other purchasers. Specific values for these minimum performance specifications are not a part of this document.
Standard

Lattice Boom Cranes - Method of Test

2019-11-13
CURRENT
J987_201911
This SAE Standard applies to mobile construction-type lifting cranes utilizing pendant-supported, conventional, and luffing jib type lattice boom crane structures.
Standard

Profiles for V2X-Based Fee Collection

2019-11-12
WIP
J3217
This WIP is to develop a standards document to define the concept of operations including reference system architecture, the user needs, the system functional and performance requirements, the message, the related data elements and frames, and other related aspects to enable V2X toll and other financial transactions.
Standard

Acrylonitrile Butadiene (Nbr) Rubber, Aromatic Fuel Resistant, 55-65

2019-11-12
WIP
AMS3212R
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves, requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both, but usage is not limited to such applications.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2019-11-12
WIP
J429
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Health, Safety and First Aid

2019-11-12
CURRENT
AS6286/5A
This document shall be used in conjunction with: AS6286 - Training and Qualification Program for Deicing/Anti-icing of Aircraft on the Ground AS6286/1 - Processes including Methods AS6286/2 - Equipment AS6286/3 - Fluids AS6286/4 - Weather AS6286/6 - Aircraft Deicing/Anti-icing Diagrams, No-Spray-Zones
Standard

Deicing/Anti-Icing Diagrams/No Spray Zones

2019-11-12
CURRENT
AS6286/6A
This document shall be used in conjunction with: - AS6286, Training and Qualification Program for Deicing/Anti-icing of Aircraft on the Ground - AS6286/1, Processes Including Methods - AS6286/2, Equipment - AS6286/3, Fluids - AS6286/4, Weather - AS6286/5, Health, Safety and First Aid
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2019-11-11
WIP
J2403DA

This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.

Standard

Automotive Pipe, Filler, and Drain Plugs

2019-11-10
WIP
J531
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
Best Practice

AVSC Best Practice for In-Vehicle Fallback Test Driver Selection, Training, and Oversight Procedures for Automated Vehicles Under Test

2019-11-08
CURRENT
AVSC00001201911
Best Practice for in-vehicle fallback test driver (safety operator) selection, training, and oversight procedures for automated vehicles under test (AVSC000012019MM) addresses the qualifications and training for on-board human oversight of testing for automated driving system (ADS)-operated vehicles. It provides an outline with criteria commonly agreed to by members of the AVSC, which includes: Driver selection Basic Driver training ADS-operation training Initial driving on public roads Periodic re-evaluation and training The Best Practice applies to humans within the vehicle responsible for the safe oversight of development and testing SAE Level 4 and Level 5 automated driving systems on public roads.
Standard

Logistics Product Data

2019-11-06
CURRENT
GEIASTD0007C
SAE GEIA-STD-0007C defines logistics product data g enerated during the requirement definition and design of an industry or government system, end item, or product. It makes use of the Extensible Markup Language (XML) through the use of entities and attributes that comprise logistics product data and their definitions. The standard is designed to provide users with a uniform set of data tags for all or portions of logistics product data. The standard can be applied to any industry or government product, system or equipment acquisition program, major modification program, and applicable research and development projects. This standard is for use by both industry and government activities. As used in this standard, the requiring authority is generally the customer and the customer can be a government or industry activity. The performing activity may be either a industry or government activity.
Standard

Wide Base Disc Wheels and Demountable Rims

2019-11-05
WIP
J876
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheel and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
X