Refine Your Search

Topic

Author

Search Results

Standard

Automatic Transmissions - Schematic Diagrams

2019-11-19
CURRENT
J647_201911
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied), and in gear. For illustrative purposes, some typical transmissions are shown.
Standard

Human Engineering - Principles and Practices

2019-11-18
WIP
HEB1C
This Engineering Bulletin and its annexes provide guidance on the application of Human Engineering principles and practices to the analysis, design, development, testing, fielding, support, accident investigation, and training for military and commercial products throughout their intended life cycles.
Standard

Qualified Hoses for Marine Applications

2019-11-14
WIP
J1942/1
The following list consists of hose data provided as of December 2018, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a. Successfully test their hose to the requirements of SAE J1942, Table 1. b. Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results. All sizes should be included in the same letter which must also include all of the information necessary to make a SAE J1942-1 listing. c.
Standard

V-Belts and Pulleys

2019-11-14
WIP
J636
This specification covers standard dimensions, tolerances, and methods of measurement of V-belts and pulleys for automotive V-belt drives.
Standard

FTIR Gas Analyzer Performance Evaluation / Qualification for Automotive Testing

2019-11-13
WIP
J2992
The scope of this document focuses on the tests required by EPA to validate the performance of the FTIR system following the section in the Code of Federal Regulations Part 1065 (40CFR1U.1065 and hereafter referred to as “EPA Part 1065”) on the guidelines and performance criteria for various regulated gases. This document focuses on the use of continuous emissions sampling for both Engine and Vehicle testing. Future addenda will be needed to cover bag and other sampling techniques. Gas components that do not currently have performance criteria but may soon be regulated are noted and EPA suggestions as to what should be required are applied. This will help ensure that the FTIR will be recognized as a valid and alternative tool for engine exhaust emissions testing. Components in engine exhaust that are specifically called out in this document include: carbon monoxide (CO), carbon dioxide (CO2), oxides of nitrogen (NO, NO2 and N2O), ammonia (NH3), methane (CH4), and formaldehyde (H2CO).
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2019-11-11
WIP
J2403DA

This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.

Standard

Balancing Machine Proving Rotors

2019-11-01
WIP
ARP4162C
This SAE Aerospace Recommended Practice (ARP) specifies a series of balancing machine proving rotors and related test weights as directly required for the evaluation of gas turbine rotor balancing machines.
Standard

Fiberboard Crease Bending Test

2019-10-31
CURRENT
J119_201910
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Paint and Trim Code Location

2019-10-24
CURRENT
J2235_201910
This SAE Recommended Practice is designed to provide readily accessible paint and trim code information on all passenger vehicles, lightweight trucks, and vans in a way that minimizes the time and effort required to locate and effectively use that information for body repair, parts ordering, vehicle maintenance, and information systems.
Standard

Unmanned Systems (UxS) Control Segment (UCS) Architecture: Version Description Document

2019-10-23
WIP
AIR6520A
Governance of the Unmanned Aircraft System (UAS) Control Segment (UCS) Architecture was transferred from the United States Office of the Secretary of Defense (OSD) to SAE International in April 2015. Consequently, a subset of the UCS Architecture Library Release 3.4(PR) has been published under SAE as the Unmanned Systems (UxS) Control Segment (UCS) Architecture, AS6512. This Version Description Document (VDD) describes the correspondence and differences between the two architecture libraries.
Standard

Unmanned Systems (UxS) Control Segment (UCS) Architecture: Conformance Specification

2019-10-23
WIP
AS6513A
This document is the authoritative specification within the SAE Unmanned Systems (UxS) Control Segment (UCS) Architecture for establishing conformance requirements for UCS products. The UCS products addressed by this specification are UCS software components and UCS software configurations that provide one or more UCS services, and UCS systems that employ one or more UCS services. The conformance of UCS products is determined by assessing the conformance of the UCS product description to the UCS Architecture. The UCS product description includes test artifacts.
Standard

Overhead Protection for Agricultural Tractors - Test Procedures and Performance Requirements

2019-10-23
WIP
J167
This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
X