Refine Your Search

Topic

Author

Search Results

Standard

Quality Management Systems - Audit Requirements for Aviation, Space, and Defense Organizations

2019-08-21
WIP
AS9101G
This standard defines requirements for the preparation and execution of the audit process. In addition, it defines the content and composition for the audit reporting of conformity and process effectiveness to the 9100-series standards, the organization's QMS documentation, and customer and statutory/regulatory requirements. The requirements in this standard are additions or represent changes to the requirements and guidelines in the standards for conformity assessment, auditing, and certification as published by ISO/IEC (i.e., ISO/IEC 17000, ISO/IEC 17021-1). When there is conflict with these standards, the requirements of the 9101 standard shall take precedence. NOTE 1: In this standard, the term “9100-series standards” comprises the following Aerospace Quality Management System (AQMS) standards: 9100, 9110, and 9120; developed by the IAQG and published by various national standards bodies.
Standard

Aerospace First Article Inspection Requirement

2019-08-21
WIP
AS9102C
This standard establishes the baseline requirements for performing and documenting FAI. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the applicable statutory or regulatory requirements shall take precedence.
Standard

Earned Value Management Systems

2019-08-19
WIP
EIA748E
An Earned Value Management System (EVMS) for integrated program management will effectively integrate the work scope of a program with the schedule and cost elements for optimum program planning and control. The primary purpose of the system is to support integrated program management. The system is owned by the organization and is governed by the organization’s policies and procedures.
Standard

Unshielded High Voltage Primary Cable

2019-08-12
WIP
J1654
This SAE Standard covers unshielded cable intended for use at a nominal system voltage up to 600 V or 1000 V (AC rms or DC). It is intended for use in surface vehicle electrical systems.
Standard

Gaining Approval for Seats with Integrated Electronics in Accordance with AC21-49 Option 7b

2019-08-07
CURRENT
AIR6448A
The primary purpose of this document is to provide roles, responsibilities and accountabilities to meet AC 21-49 Section 7.b ‘Type Certification using TSO-approved seat with electronic components defined in TSO design’. This document may be applied to all applicable seat TSOs (C39(), C127()…etc). The approval for the integration of the electronics will fall, in part or in full, under the type design authority of the Seat Installer rather than the Seat Supplier shipping the integrated seat. The defined responsibilities, areas of authority and accountability of each party, as well as necessary communication protocols, must ensure configuration management, design control and quality control. These definitions, controls and protocols are agreed (thru normal commerical agreements and binding contracts) and adhered to by all parties ensuring all parts in the supply chain remain approved (e.g. certified and conformed).
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

2019-08-07
CURRENT
J174_201908
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

Laboratory Viscosity Measurement of Thickened Aircraft Deicing/Anti-icing Fluids with the Brookfield LV Viscometer

2019-08-01
WIP
AS9968A
This AS describes a standard method for viscosity measurements of thickened (AMS1428) anti-icing fluids. Fluid manufacturers may publish alternate methods for their fluids. In case of conflicting results between the two methods, the manufacturer method takes precedence. To compare viscosities, exactly the same measurement elements (including spindle and container size) must have been used to obtain those viscosities.
X