Refine Your Search

Topic

Author

Search Results

Standard

Metallic Whiskers

2019-10-17
CURRENT
AIR4129A
This AIR presents an abbreviated review of the metallurgical phenomena known as whiskers. It is not all encompassing; rather, it is intended to introduce the design engineer to the technical issues of metallic whiskers, their formation, and the potentially dangerous problems they can cause.
Standard

Primer, Anodic Electrodeposition for Aircraft Applications

2019-10-17
CURRENT
AMS3144A
This specification establishes the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
Standard

Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated

2019-10-17
CURRENT
AMS4173G
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing. These extrusions have been used typically for parts requiring moderate strength and where distortion during machining must be minimized, but usage is not limited to such applications.
Standard

Vehicle Lift Points for Service Garage Lifting

2019-10-16
CURRENT
J2184_201910
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
Standard

Low-duty Inertia Dynamometer Hydraulic Brake Wear Test Procedures for Vehicles Above 4536 kg (10 000 lb) of GVWR

2019-10-15
WIP
J3006
This Recommended Practice is derived from OEM and tier-1 laboratory tests and applies to two-axle multipurpose passenger vehicles, or trucks with a GVWR above 4536 kg (10 000 pounds) equipped with hydraulic disc or drum service brakes. Before conducting testing for a specific brake sizes or under specific test conditions, review, agree upon, and document with the test requestor any deviations from the test procedure. Also, the applicable criteria for the final test results and wear rates deemed as significantly different require definition, assessment, and proper documentation; especially as this will determine whether or not Method B testing is needed. This Recommended Practice does not evaluate or quantify other brake system characteristics such as performance, noise, judder, ABS performance, or braking under extreme temperatures or speeds. Minimum performance requirements are not part of this recommended practice.
Standard

Aerospace-Solenoid Valve, Hydraulic, Three Way, Two Position, Direct Acting

2019-10-10
WIP
ARP4945B
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to aid in the specifying and testing of direct acting three way, two position, single and multiple coil, normally open and normally closed solenoid valves used for the pilot actuation of hydraulic control systems and the control of hydraulic components. The information presented should be useful in standardizing terminology, in specifying requirements and performance parameters, and in defining test methods. The recommendations do not restrict or attempt to define the internal design features of solenoid valves. Standard mechanical, electrical and fluid porting interfaces are recommended to provide commonalty, interchangeability, design flexibility and to be more affordable. In general, this recommended practice is directed toward solenoid valves for use in military and commercial flight control and hydraulic actuation systems.
Standard

Radiator Caps and Filler Necks

2019-10-09
WIP
J164

This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.

Standard

Engine Oil Viscosity Classification

2019-10-09
WIP
J300
This SAE Standard defines the limits for a classification of engine lubricating oils in rheological terms only. Other oil characteristics are not considered or included.
Standard

Domestic Performance Torque Converter Manufacturing

2019-10-09
CURRENT
J2440_201910
The scope of this SAE Draft Technical Report is to establish dimensional standards for high-performance domestic torque converter manufacturers. Many torque converter manufacturers build converters to their own standards. Some of these standards may be outside of the specification that define a quality performance torque converter.
X