This specification covers the general requirements for aluminum alloy bar, rod, shapes, structural shapes, tube, and wire extruded. Specific requirements for these products in a particular alloy are covered by the applicable detailed specification (See 6.3).
The following list consists of hose data provided as of December 2018, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a. Successfully test their hose to the requirements of SAE J1942, Table 1. b. Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results. All sizes should be included in the same letter which must also include all of the information necessary to make a SAE J1942-1 listing. c.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves, requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both, but usage is not limited to such applications.
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layer of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc.
SAE GEIA-STD-0007C defines logistics product data g enerated during the requirement definition and design of an industry or government system, end item, or product. It makes use of the Extensible Markup Language (XML) through the use of entities and attributes that comprise logistics product data and their definitions. The standard is designed to provide users with a uniform set of data tags for all or portions of logistics product data. The standard can be applied to any industry or government product, system or equipment acquisition program, major modification program, and applicable research and development projects. This standard is for use by both industry and government activities. As used in this standard, the requiring authority is generally the customer and the customer can be a government or industry activity. The performing activity may be either a industry or government activity.
This specification covers a corrosion-resistant steel in the form of cold-worked bars and wire up to 1.750 inch (44.45 mm) inclusive, in nominal diameter or least distance between parallel sides (see 8.4).
This specification covers a free-machining, corrosion-resistant steel in the form of cold-worked bars and wire up to 1.750 inches (44.45 mm) inclusive, in nominal diameter or least distance between parallel sides (see 8.5).
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of nickel, nickel alloys, and cobalt alloys ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.
This SAE Aerospace Information Report (AIR) provides a general description of methods for hardness testing of O-Rings including factors which affect precision and comparison of results with those obtained in standard tests.
Purpose and Applicability The purpose of this document is to provide detailed requirements to preclude the use of counterfeit fasteners in end-item equipment where the consequence of such use cannot be tolerated. This document is mandatory when the Customer has invoked it in the contract. The requirements of this document are intended to supplement the requirements of a higher level quality standard (e.g., AS/EN/JISQ9100, ISO-9001, ANSI/ASQC E4, ASME NQA-1, AS9120, AS9003, and ISO/TS 16949 or equivalent) and other quality management system documents. Fasteners are defined as United States Federal Supply Classification Group codes as shown in the following list: 5305 Screws 5306 Bolts 5307 Studs 5310 Nuts and Washers 5315 Nails, Machine Keys, and Pins 5320 Rivets 5325 Fastening Devices 5340 Miscellaneous Hardware - Specific parts in this hardware industry code are applicable, including but not limited to clamps, hinges, coiled insert fasteners and clinch-nut fasteners.
This SAE Aerospace Recommended Practice (ARP) specifies a series of balancing machine proving rotors and related test weights as directly required for the evaluation of gas turbine rotor balancing machines.