Standard
Nickel Wire and Ribbon 99Ni
2024-04-01
CURRENT
AMS5555G
This specification covers a nickel in the form of round wire and rectangular ribbon.
Search Results
Standard
Powder, Plasma Spray 50 (88WC - 12Co) + 35 (70Ni - 16.5Cr - 4Fe - 4Si - 3.8B) + 15 (80Ni - 20Al) Three-Component Mixture
2024-04-01
CURRENT
AMS5792C
This specification covers a blend of tungsten carbide-cobalt aggregate, a nickel alloy, and a nickel aluminum aggregate in the form of powder.
Standard
Pins, Cotter, Steel, Corrosion Resistant UNS S30200 Procurement Specification for
2024-04-01
CURRENT
AS7210B
This procurement specification covers split cotter pins with optional ends (see Figure 1), made from a corrosion resistant steel of the type identified under the Unified Numbering System as UNS S30200.
Standard
Steel Bars, Forgings, and Mechanical Tubing and Forging Stock, Carburizing, Aircraft Quality, 0.50Cr - 1.8Ni - 0.25Mo - (0.17 - 0.23C), (SAE 4320H)
2024-04-01
CURRENT
AMS6299H
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Standard
Spring Pins, Tubular, Carbon Steel, Procurement Specification for
2024-04-01
CURRENT
AS7205A
This specification covers tubular-shaped pins, fabricated from carbon steel, having a full-length longitudinal slot to permit flexure when inserted into a hole.
Standard
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged
2024-04-01
CURRENT
AMS4344G
This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles 0.250 to 2.000 inches (6.35 to 50.80 mm) in nominal thickness and up to 32 square inches (206 cm2), inclusive, in cross-sectional area (see 8.5).
Standard
Steel, Corrosion- and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings, and Stock for Forgings and Flash-Welded Rings 17Cr (430), Annealed
2024-04-01
CURRENT
AMS5627J
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.
Standard
Aluminum Alloy, Extrusions and Rings, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6), Solution and Precipitation Heat Treated
2024-03-27
CURRENT
AMS4150P
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash-welded rings fabricated from extruded stock, and stock for flash-welded rings (see 8.6).
Standard
CRIMPING TOOLS, TYPE 1, TERMINAL, HAND, WIRE TERMINATION FOR WIRE BARREL SIZES 16, AND SMALLER
2024-03-22
CURRENT
AS22520/7A
Standard
ROD END - THREADED, AIRCRAFT
2024-03-22
CURRENT
AS49011C
Standard
Spring Pins, Tubular, Coiled Corrosion Resistant Nickel Base Alloy Procurement Specification For
2024-03-22
CURRENT
AS4983A
This procurement specification covers tubular-shaped, coiled spring pins made of a corrosion resistant nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
Standard
Aluminum Alloy Extrusions, 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T73511), Solution Heat Treated, Stress Relieved, and Overaged
2024-03-22
CURRENT
AMS4157F
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing 5.000 inches (127.00 mm) and under in nominal diameter or least thickness (wall thickness of tubing) (see 8.5).
Standard
Nickel Alloy, Corrosion- and Heat-Resistant, Sheet, Strip, and Plate 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe (Alloy X or HX) Solution Heat Treated
2024-03-22
CURRENT
AMS5536R
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
Standard
JAUS Messaging over the OMG Data Distribution Service (DDS)
2024-03-18
CURRENT
ARP6227
This document defines a standard representation of JAUS AS5684A message data in DDS IDL defined by the Object Management Group (OMG) CORBA 3.2 specification. This document does NOT address how JAUS transport considerations or JAUS service protocols are implemented on OMG DDS platforms.
Standard
Engine and Transmission Identification Numbers
2024-03-18
CURRENT
J129_202403
This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853.
Standard
BEARING, ROLLER, NEEDLE, SINGLE ROW, HEAVY DUTY, TYPE I, ANTIFRICTION, INCH
2024-03-18
CURRENT
AS24461E
Standard
Aluminum Alloy, Die and Hand Forgings, 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T74), Solution and Precipitation Heat Treated
2024-03-18
WIP
AMS4149G
This specification covers an aluminum alloy in the form of die and hand forgings 6.000 inches (152.00 mm) and under in nominal thickness at time of heat treatment (see 8.6).
Standard
Steel, Corrosion-Resistant, Bars, Wire, Forgings, Extrusions, Mechanical Tubing, Rings, and Stock for Forgings, Extrusions, and Rings, Wear and Galling Resistant, 8.0Mn - 4.0Si - 17Cr - 8.5Ni - 0.13N Solution Heat Treated
2024-03-18
CURRENT
AMS5848F
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, extrusions, mechanical tubing, flash-welded rings, and stock for forging, extruding, or flash-welded rings.
Standard
Aluminum Alloy, Alclad Sheet 3.8Cu - 1.0Mg - 0.30Mn - 0.60Zn (Alclad 2056-T3) Solution Heat Treated and Cold Worked
2024-03-12
CURRENT
AMS4298B
This specification covers an aluminum alloy in the form of sheet 0.063 to 0.236 inch (1.60 to 6.00 mm), incl, in thickness, clad on both sides (see 8.4).
Standard
Motor Vehicle Brake Fluid Based Upon Glycols, Glycol Ethers, and the Corresponding Borates
2024-03-12
CURRENT
J1704_202403
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and borates of glycol ethers, and appropriate inhibitors for use in the braking system of any motor vehicle, such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR) or a terpolymer of ethylene, propylene, and a diene (EPDM).
