Refine Your Search

Topic

Author

Search Results

Standard

Procedure for Inspection of In-Service Airborne Accumulators for Corrosion and Damage

2019-11-12
CURRENT
ARP4150A
This SAE Aerospace Recommended Practice (ARP) is a guide in establishing inspection procedures to determine the condition of in-service accumulators. Recommendations are also provided for corrective action if it is determined that the environment is contributing to the deterioration of the surface protection system treatments.
Standard

Acrylonitrile Butadiene (Nbr) Rubber, Aromatic Fuel Resistant, 55-65

2019-11-12
WIP
AMS3212R
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves, requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both, but usage is not limited to such applications.
Standard

Anodized Aluminum Automotive Parts

2019-11-11
WIP
J399
Automotive parts can be fabricated from either coiled sheet, flat sheet or extruded shapes. Alloy selection is governed by finish requirements, forming characteristics, and mechanical properties. Bright anodizing alloys 5657 and 5252 sheet provide a high luster and are preferred for trim which can be formed from an intermediate temper, such as H25. Bright anodizing alloy 5457 is used for parts which require high elongation and a fully annealed ('0') temper. Alloy 6463 is a medium strength bright anodizing extrusion alloy; Alloy X7016 is a high strength bright anodizing extrusion alloy primarily suited for bumper applications. To satisfy anti-glare requirements for certain trim applications, sheet alloy 5205 and extrusion alloy 6063 are capable of providing the desired low-gloss anodized finish.
Standard

Electroplating and Related Finishes

2019-11-11
WIP
J474
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layer of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc.
Standard

Methods of Measuring Case Depth

2019-11-11
WIP
J423
Case hardening may be defined as a process for hardening a ferrous material in such a manner that the surface layer, known as the case, is substantially harder than the remaining material, known as the core. The process embraces carburizing, nitriding, carbonitriding, cyaniding, induction, and flame hardening. In every instance, chemical composition, mechanical properties, or both are affected by such practice. This testing procedure describes various methods for measuring the depth to which change has been made in either chemical composition or mechanical properties. Each procedure has its own area of application established through proved practice, and no single method is advocated for all purposes. Methods employed for determining the depth of case are either chemical, mechanical, or visual, and the specimens or parts may be subjected to the described test either in the soft or hardened condition.
Standard

Automotive Pipe, Filler, and Drain Plugs

2019-11-10
WIP
J531
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
Standard

Hydrogen Embrittlement Testing of Ultra High Strength Steels and Stampings by Acid Immersion

2019-11-07
WIP
J3215
This standard describes a test method for evaluating the susceptibility of cold rolled and hot rolled Ultra High Strength Steels (UHSS) to hydrogen embrittlement. The thickness range of materials that can be evaluated is limited by the ability to bend and strain the material to the specified stress level in the specification. Hydrogen embrittlement can occur with any steel with a tensile strength greater than about 1000 MPa, although some steel microstructures, especially those with retained austenite, may be susceptible at lower tensile strengths under the right conditions. The presence of available hydrogen, high stress levels and materials of high strength are considered the most at risk for hydrogen embrittlement. Due to the specific conditions that need to be present for hydrogen embrittlement to occur, cracking in this test does not indicate that parts made from that material would crack in an automotive environment.
Standard

Laser Peening

2019-11-06
WIP
TEMPAMS2546
This project is initiated so that balloting of AMS2546 can be done within ASEC.
Standard

Logistics Product Data

2019-11-06
CURRENT
GEIASTD0007C
SAE GEIA-STD-0007C defines logistics product data g enerated during the requirement definition and design of an industry or government system, end item, or product. It makes use of the Extensible Markup Language (XML) through the use of entities and attributes that comprise logistics product data and their definitions. The standard is designed to provide users with a uniform set of data tags for all or portions of logistics product data. The standard can be applied to any industry or government product, system or equipment acquisition program, major modification program, and applicable research and development projects. This standard is for use by both industry and government activities. As used in this standard, the requiring authority is generally the customer and the customer can be a government or industry activity. The performing activity may be either a industry or government activity.
Standard

10/15/14Hydraulic Flange Clamps, 2-Screw Flange Connection to be used with SAE J518-1 (Code 61) Connections where Only Low Pressure is Required

2019-11-06
WIP
J518/3
This SAE standard outlines general and dimensional specifications for Code 61 flange clamps for use in low pressure applications with J518-1 connections. For port dimensions, port design considerations, and flange head dimensions, please refer to SAE J518-1. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail. Parts manufactured to this standard are also compatible with ISO 6162-1 port connections and flange heads.
Standard

Tolerances, Nickel, Nickel Alloy, and Cobalt Alloy Sheet, Strip, and Plate

2019-11-05
CURRENT
AMS2262H
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of nickel, nickel alloys, and cobalt alloys ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.
X