Refine Your Search

Topic

Author

Search Results

Standard

Friction Material Elastic Constants Determination through FRF Measurements and Optimization

2019-10-17
WIP
J3013
This SAE Standard specifies necessary procedures and control parameters in estimating anisotropic elastic constants of friction material based on pad assembly FRF measurements and optimization. It is intended to provide a set of elastic constants as inputs to brake NVH simulation, with the objective of ensuring pad assembly vibration correlation between simulation and measurements.
Standard

Metallic Whiskers

2019-10-17
CURRENT
AIR4129A
This AIR presents an abbreviated review of the metallurgical phenomena known as whiskers. It is not all encompassing; rather, it is intended to introduce the design engineer to the technical issues of metallic whiskers, their formation, and the potentially dangerous problems they can cause.
Standard

Primer, Anodic Electrodeposition for Aircraft Applications

2019-10-17
CURRENT
AMS3144A
This specification establishes the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
Standard

Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated

2019-10-17
CURRENT
AMS4173G
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing. These extrusions have been used typically for parts requiring moderate strength and where distortion during machining must be minimized, but usage is not limited to such applications.
Standard

Minimum General Standards for Oxygen Systems

2019-10-16
WIP
AS861C
This standard covers all types of oxygen breathing equipment used in non-military aircraft. It is intended that this standard supplement the requirements of the detail specification or drawings of specific components or assemblies, e.g., regulators, masks, cylinders, etc. Where a conflict exists between this and detail specifications, detail specifications shall take precedence.
Standard

Vehicle Lift Points for Service Garage Lifting

2019-10-16
CURRENT
J2184_201910
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
Standard

Aerospace-Solenoid Valve, Hydraulic, Three Way, Two Position, Direct Acting

2019-10-10
WIP
ARP4945B
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to aid in the specifying and testing of direct acting three way, two position, single and multiple coil, normally open and normally closed solenoid valves used for the pilot actuation of hydraulic control systems and the control of hydraulic components. The information presented should be useful in standardizing terminology, in specifying requirements and performance parameters, and in defining test methods. The recommendations do not restrict or attempt to define the internal design features of solenoid valves. Standard mechanical, electrical and fluid porting interfaces are recommended to provide commonalty, interchangeability, design flexibility and to be more affordable. In general, this recommended practice is directed toward solenoid valves for use in military and commercial flight control and hydraulic actuation systems.
Standard

Radiator Caps and Filler Necks

2019-10-09
WIP
J164

This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.

Standard

Engine Oil Viscosity Classification

2019-10-09
WIP
J300
This SAE Standard defines the limits for a classification of engine lubricating oils in rheological terms only. Other oil characteristics are not considered or included.
Standard

Fused Filament Fabrication, Process Specification for

2019-10-09
CURRENT
AMS7100
This specification establishes the requirements for the production of reliable, repeatable, reproducible aerospace parts by fused filament fabrication but is not limited to such application. This specification establishes the requirements to approve new machines, processes, and materials. Specifically, this specification covers machine configuration, operating software, machine calibration, machine and build parameters, and testing methodology required to create aerospace parts. This specification also defines the user’s responsibility for following the specified requirements.
X