Refine Your Search

Topic

Author

Search Results

Standard

Forgings, Steel, For Aircraft/Aerospace Equipment

2019-10-21
WIP
AMS6400A

This specification establishes requirements for steel forgings of any shape or form from which finished parts are to be made (See 8.2, 8.3, & 8.4). This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment

Standard

Corrosion Test Master Establishment

2019-10-21
CURRENT
J2636_201910
This SAE lab recommended practice may be applied to corrosion test methods such as salt spray, filiform, Corrosion creep back, etc. This procedure is intended to permit corrosion testing to be assessed between Laboratories for correlation purposes.
Standard

Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated

2019-10-17
CURRENT
AMS4173G
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing. These extrusions have been used typically for parts requiring moderate strength and where distortion during machining must be minimized, but usage is not limited to such applications.
Standard

Vehicle Lift Points for Service Garage Lifting

2019-10-16
CURRENT
J2184_201910
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
Standard

Radiator Caps and Filler Necks

2019-10-09
WIP
J164

This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.

Standard

Engine Oil Viscosity Classification

2019-10-09
WIP
J300
This SAE Standard defines the limits for a classification of engine lubricating oils in rheological terms only. Other oil characteristics are not considered or included.
Standard

Passenger Car Side Door Latch Systems

2019-10-09
CURRENT
J839_201910
This SAE Recommended Practice establishes minimum performance requirements and test procedures for evaluating and testing passenger car side door latch systems. It is limited to tests that can be conducted on uniform test fixtures and equipment in commercially available laboratory test facilities. The test procedures and minimum performance requirements outlined in this document are based on currently available engineering data. It is intended that all portions of the document will be periodically reviewed and revised, as additional knowledge regarding vehicle latch performance under impact conditions is developed.
Standard

Nomenclature - Hydraulic Backhoes

2019-10-09
WIP
J326
This SAE standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.
Standard

Domestic Performance Torque Converter Manufacturing

2019-10-09
CURRENT
J2440_201910
The scope of this SAE Draft Technical Report is to establish dimensional standards for high-performance domestic torque converter manufacturers. Many torque converter manufacturers build converters to their own standards. Some of these standards may be outside of the specification that define a quality performance torque converter.
Standard

Vehicle Passenger Door Hinge Systems

2019-10-09
CURRENT
J934_201910
The scope of this SAE Recommended Practice is to establish recommended uniform test procedures and minimum static load requirements for vehicle passenger door hinge systems. Tests are described that can be conducted on test fixtures and equipment in laboratory test facilities. The test procedures and minimum performance requirements outlined in this document are based on currently available engineering data. It is intended that all portions of the document be periodically reviewed and revised as additional knowledge regarding vehicle hinge system performance under impact conditions is developed.
Standard

Fluid, Jet Reference

2019-10-03
WIP
AMS2629F
This specification covers a mixture of liquid hydrocarbons and soluble additives.
X