Search Results

Standard

Fuel and Lubricant Tanks for Motorcycles

2024-04-15

CURRENT

J1241_202404

This SAE Recommended Practice is applicable to two- or three-wheel motorcycles intended for highway use. Unless noted, requirements apply to both metallic and nonmetallic tanks. Accessory or aftermarket tanks as well as original equipment tanks are covered.

Standard

High Flow Liquid Hydrogen Fueling Couplings for Aerospace and Heavy Transport Applications

2024-04-15

WIP

AIR8999

The SAE AE-5CH Taskgroup has determined that high flow liquid hydrogen fueling couplings need to be developed in order to fast fill aircraft at the airport. Though the flow rates from a current liquid hydrogen bayonet connect may reach the lower bound flow rates of regional aircraft, there are some shortcomings to this connector for aerospace. For this reason a new specification for flow rates for regional to narrowbody (and potentially later widebody) are to be developed in this documenet. Harmonization for lower flow rates (such as up to 20kg/minute) are planned to be harmonized with ground vehicle fueling such as with ISO 13984. Within this document,coupling descriptions including Flow rates from 84 to 200 kg/minute will be evaluated (and potentially higher), and requirements and testing and safety targets will be specified.

Standard

Nickel Wire and Ribbon 99Ni

2024-04-01

CURRENT

AMS5555G

This specification covers a nickel in the form of round wire and rectangular ribbon.

Standard

Powder, Plasma Spray 50 (88WC - 12Co) + 35 (70Ni - 16.5Cr - 4Fe - 4Si - 3.8B) + 15 (80Ni - 20Al) Three-Component Mixture

2024-04-01

CURRENT

AMS5792C

This specification covers a blend of tungsten carbide-cobalt aggregate, a nickel alloy, and a nickel aluminum aggregate in the form of powder.

Standard

Pins, Cotter, Steel, Corrosion Resistant UNS S30200 Procurement Specification for

2024-04-01

CURRENT

AS7210B

This procurement specification covers split cotter pins with optional ends (see Figure 1), made from a corrosion resistant steel of the type identified under the Unified Numbering System as UNS S30200.

Standard

Steel Bars, Forgings, and Mechanical Tubing and Forging Stock, Carburizing, Aircraft Quality, 0.50Cr - 1.8Ni - 0.25Mo - (0.17 - 0.23C), (SAE 4320H)

2024-04-01

CURRENT

AMS6299H

This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

Standard

Spring Pins, Tubular, Carbon Steel, Procurement Specification for

2024-04-01

CURRENT

AS7205A

This specification covers tubular-shaped pins, fabricated from carbon steel, having a full-length longitudinal slot to permit flexure when inserted into a hole.

Standard

Evaluation of Thermal Stability and Corrosivity of Aviation Lubricants

2024-04-01

CURRENT

ARP6992

This test method describes a standardized process to evaluate an aviation lubricant’s resistance to thermal degradation and to evaluate the fluid’s tendency to corrode a steel specimen. Fluids are evaluated in an environment free of both air and moisture at a specified temperature and for a specified time period.

Standard

Screw Threads - MJ Profile, Metric

2024-04-01

CURRENT

MA1370A

This standard specifies the characteristics of the MJ profile metric series of screw threads, altered from ISO 68 M Profile, to include a mandatory controlled radius of 0.18042P to 0.15011P at the root of the external thread and with the minor diameter of both external and internal threads increased to provide a basic thread height of 0.5625H in order to accommodate the external thread maximum root radius.

Standard

Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged

2024-04-01

CURRENT

AMS4344G

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles 0.250 to 2.000 inches (6.35 to 50.80 mm) in nominal thickness and up to 32 square inches (206 cm2), inclusive, in cross-sectional area (see 8.5).

Standard

Steel, Corrosion- and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings, and Stock for Forgings and Flash-Welded Rings 17Cr (430), Annealed

2024-04-01

CURRENT

AMS5627J

This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.

Standard

Aluminum Alloy, Extrusions and Rings, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6), Solution and Precipitation Heat Treated

2024-03-27

CURRENT

AMS4150P

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash-welded rings fabricated from extruded stock, and stock for flash-welded rings (see 8.6).

Standard

Battery Electric Vehicle Energy Consumption and Range Test Procedure

2024-03-26

WIP

J1634

This SAE Recommended Practice establishes uniform procedures for testing battery electric vehicles (BEVs) which are capable of being operated on public and private roads. The procedure applies only to vehicles using batteries as their sole source of power. It is the intent of this document to provide standard tests which will allow for the determination of energy consumption and range for light-duty vehicles (LDVs) based on the federal emission test procedure (FTP) using the urban dynamometer driving schedule (UDDS) and the highway fuel economy driving schedule (HFEDS) and provide a flexible testing methodology that is capable of accommodating additional test cycles as needed. Additionally, this SAE Recommended Practice provides five-cycle testing guidelines for vehicles performing supplementary testing on the US06, SC03, and cold FTP procedure. Realistic alternatives should be allowed for new technology.

Standard

CRIMPING TOOLS, TYPE 1, TERMINAL, HAND, WIRE TERMINATION FOR WIRE BARREL SIZES 16, AND SMALLER

2024-03-22

CURRENT

AS22520/7A

Standard

ROD END - THREADED, AIRCRAFT

2024-03-22

CURRENT

AS49011C

Standard

Spring Pins, Tubular, Coiled Corrosion Resistant Nickel Base Alloy Procurement Specification For

2024-03-22

CURRENT

AS4983A

This procurement specification covers tubular-shaped, coiled spring pins made of a corrosion resistant nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.

Standard

Aluminum Alloy Extrusions, 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T73511), Solution Heat Treated, Stress Relieved, and Overaged

2024-03-22

CURRENT

AMS4157F

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing 5.000 inches (127.00 mm) and under in nominal diameter or least thickness (wall thickness of tubing) (see 8.5).

Standard

JAUS Messaging over the OMG Data Distribution Service (DDS)

2024-03-18

CURRENT

ARP6227

This document defines a standard representation of JAUS AS5684A message data in DDS IDL defined by the Object Management Group (OMG) CORBA 3.2 specification. This document does NOT address how JAUS transport considerations or JAUS service protocols are implemented on OMG DDS platforms.

Standard

Engine and Transmission Identification Numbers

2024-03-18

CURRENT

J129_202403

This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853.

Standard

BEARING, ROLLER, NEEDLE, SINGLE ROW, HEAVY DUTY, TYPE I, ANTIFRICTION, INCH

2024-03-18

CURRENT

AS24461E