Search Results

Finding ways to reduce the amount of fuel burned per flight takes top priority in aircraft operations and design. Three experts show how the smallest on-board components can make a huge difference.

The development of PM and NOx reduction system with the combination of DOC included DPF and SCR catalyst in addition to the AOC sub-assembly for NH3 slip protection is described. DPF regeneration strategy and manual regeneration functionality are introduced with using ITH, HCI device on the EUI based EGR, VGT 12.3L diesel engine at the CVS full dilution tunnel test bench. With this system, PM and NOx emission regulation for JPNL was satisfied and DPF regeneration process under steady state condition and transient condition (JE05 mode) were successfully fulfilled. Manual regeneration process was also confirmed and HCI control strategy was validated against the heat loss during transient regeneration mode. Presenter Seung-il Moon

The first commercially available plug-in hybrid electric vehicle (PHEV), the General Motors (GM) Volt, was introduced into the market in mid-December 2010. The Volt uses a series-split powertrain architecture, which provides benefits over the series architecture that typically has been considered for use in electric-range extended vehicles (EREVs). A specialized EREV powertrain, called the Voltec, drives the Volt through its entire range of speed and acceleration with battery power alone and within the limit of battery energy, thereby displacing more fuel with electricity than a PHEV, which characteristically blends electric and engine power together during driving. This paper assesses the benefits and drawbacks of these two different plug-in hybrid electric architectures (series versus series-split) by comparing component sizes, system efficiency, and fuel consumption over urban and highway drive cycles.

The need for light-weighting of automotive structures has spurred on a tremendous amount of interest in and development of low cost carbon fiber composite materials and manufacturing. This presentation provides a description of the commercial carbon fiber concept compared to traditional aerospace and specialty carbon fiber products. A specific update is presented on the development and commercialization of new low cost carbon fiber based on lignin / PAN precursor technology. The second focus of the presentation is on carbon fiber composite manufacturing processes, including carbon SMC, RTM, prepregs, and thermoplastic processes. Advantages and disadvantages of these processes are discussed, especially related to low cost manufacturing. Presenter George Husman, Zoltek Companies Inc.

Exatec� PC glazing technology team, has developed advanced weathering and abrasion resistant coatings technology that can be applied to protect polycarbonate. It is of particular interest to quantify and understand the factors that determine the surface abrasion performance of coated PC in rear window and backlight applications that have a wiper system. In the present study we describe Exatec's lab scale wiper testing equipment and test protocols. We also describe adaptation of optical imaging system to measure contrast and nano-profiling using nano-indenter, as post wiper surface characterization methods. These methods are more sensitive to fine scratches on glazing surface than standard haze measurement and mechanical profilometry. Three coating systems were investigated; Siloxane wetcoat (A), Siloxane wetcoat (B), and Siloxane wetcoat (B) plus plasma coat (Exatec� E900 coating). The performance comparisons were made using all these surface characterization methods.

For internal combustion engines and industrial machinery, it is well recognized that the most cost-effective way of reducing energy consumption and extending service life is through lubricant development. This presentation summarizes our recent R&D achievements on developing a new class of candidate lubricants or oil additives ionic liquids (ILs). Features of ILs making them attractive for lubrication include high thermal stability, low vapor pressure, non-flammability, and intrinsic high polarity. When used as neat lubricants, selected ILs demonstrated lower friction under elastohydrodynamic lubrication and less wear at boundary lubrication benchmarked against fully-formulated engine oils in our bench tests. More encouragingly, a group of non-corrosive, oil-miscible ILs has recently been developed and demonstrated multiple additive functionalities including anti-wear and friction modifier when blended into hydrocarbon base oils.

Micro-pitting is a fatigue effect that occurs in geared transmission systems due to high contact stress, and monitoring its progression is vital to prevent the eventual failure of the tooth flank. Parameter signature analysis has been successfully used to monitor bending fatigue failure and advanced phases of gear surface fatigue failure such as macro-pitting and scuffing. However, due to modern improvements in steel production the main cause of gear contact fatigue failure can be attributed to surface micro-pitting rather than sub-surface phenomena. Responding to the consequent demand to detect and monitor the progression of micro-pitting, this study experimentally evaluated the development of micro-pitting in spur gears using vibration and oil debris analysis. The paper presents the development of an online health monitoring system for use with back-to-back gear test rigs.

A series of flight tests were conducted to design and evaluate a Combined Vision System (CVS) that integrates a forward looking infrared video image with synthetic vision on a primary flight display. System features included colorizing the video image to mesh with the synthetic terrain background, decluttering the approach symbology to facilitate the detection of the approach lights and runway markings, creating a semi-transparent IR sky to ensure continuous situational awareness of the surrounding terrain, and annunciating the decision height to facilitate the transition to the actual runway environment. Over 100 approaches were flown during three flight test sessions. For the first flight test session pilots reviewed early CVS proofs of concept on Honeywell's Citation Sovereign.

With the increased usage of Carbon Fiber Reinforced Plastics (CFRP) in the aircraft industry, there has been increased pressure to improve cutting tool life. Tungsten carbide tools were the first to be applied to CFRP materials. Poly Crystalline Diamond (PCD) tools also became an acceptable material to be used as a cutting tool material. In recent years, Chemical Vapor Deposition (CVD) diamond tools have become more popular as a cutting tool material for CFRP. This study compares these possible cutting tool materials in the drilling of CFRP. Wear is measured as well as hole quality. Life is determined by common industry standards with regard to fiber break out in a common CFRP material. An economic analysis is conducted in order to determine cost per hole. Presenter Christophe Petit

A combination of laboratory reactor measurements and vehicle FTP testing has been combined to demonstrate a method for diagnosing the formation of NO2 from a diesel oxidation catalyst (DOC). Using small cores from a production DOC and simulated diesel exhaust, the laboratory reactor experiments are used to support a model for DOC chemical reaction kinetics. The model we propose shows that the ability to produce NO2 is chemically linked to the ability of the catalyst to oxidize hydrocarbon (HC). For thermally damaged DOCs, loss of the HC oxidation function is simultaneous with loss of the NO2 production function. Since HC oxidation is the source of heat generated in the DOC under regeneration conditions, we conclude that a diagnostic of the DOC exotherm is able to detect the failure of the DOC to produce NO2. Vehicle emissions data from a 6.6 L Duramax HD pick-up with DOC of various levels of thermal degradation is provided to support the diagnostic concept.