Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Aerodynamic Analysis on under Body Drag and Vehicle Performance of Active Front Spoiler for High CG Vehicles

2019-10-11
2019-28-0025
Vehicle aerodynamic drag reduction is the effective technique to enhance the fuel economy, performance and top speed of a vehicle. Out of the total drag, the underbody drag contributes about 40-50% by the parts like wheel arch, wheel housing, and the wheels. This further increases in the case of vehicles with higher CG. Thus, it seems logical to focus attention on the underbody aerodynamic drag reduction. In this study, an active spoiler is placed towards the front end of the vehicle which will divert the air flow from the front towards the radiator. The active spoiler revolves according to the signals received from the radar sensors placed at the lower end to detect obstacles which will prevent it from damage. The aim of the study is to examine the effect of the air flow diversion on underbody drag. The effect of air flow diversion on fuel consumption, radiator effectiveness and top speed is numerically evaluated.
Technical Paper

Aerodynamic Drag Reduction of an Intercity Bus through Surface Modifications - A Numerical Simulation

2019-10-11
2019-28-0045
The maximum power produced by the Engine is utilized in overcoming the Aerodynamic resistance while the remaining has been used to overcome rolling and climbing resistance. Increasing emission and performance demands paves way for advanced technologies to improve fuel efficiency. One such way of increasing the fuel efficiency is to reduce the aerodynamic drag of the vehicle. Buses emerged as the common choice of transport for people in India. By improving the aerodynamic drag of the Buses, the diesel consumption of a vehicle can be reduced by nearly about 10% without any upgradation of the existing engine. Though 60 to 70 % of pressure loads act on the frontal surface area of the buses, the most common techniques of reducing the drag in buses includes streamlining of the surfaces, minimizing underbody losses, reduced frontal area, pressure difference between the front & rear area and minimizing of flow separation & wake regions.
Standard

Heater and Accessories, Aircraft Internal Combustion Heat Exchanger Type

2019-10-01
CURRENT
AS8040C
This SAE Aerospace Standard (AS) covers combustion heaters and accessories used in, but not limited to, the following applications: a. Cabin heating (all occupied regions and windshield heating) b. Wing and empennage anti-icing c. Engine and accessory heating (when heater is installed as part of the aircraft) d. Aircraft deicing
Technical Paper

The Szorenyi Three-Chamber Rotary Engine Concept

2019-09-09
2019-24-0168
Currently automotive engines are reciprocating or Wankel rotary engine types. Reciprocating engines are bulky, heavy and complex, mainly due to the intake and exhaust valves and their associated cam-train. Wankel engines have a low rotor rev limit, and have inefficient sealing of the apex seals leading to poor economy and undesirable emission gases. The Rotary Engine Development Agency (REDA) has designed a new three-chamber rotary internal combustion engine concept using an adaptation of the patented Szorenyi Curve. The new design is an evolution of the design which was the subject of SAE Technical Paper 2017-01-2413 and SAE publication ‘So You Want to Design Engines: UAV Propulsion Systems’. This paper describes the features of the new three-chamber engine concept and includes an analysis of the major shortcomings of the Wankel engine.
Standard

Oxygen Cylinder Quality, Serviceability, Maintenance Transfilling and Marking

2019-08-22
WIP
AIR1059F
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling of oxygen cylinder while installed on aircraft, directly or through an intermediate charging port.
Standard

Magnesium Alloys in Aircraft Seats - Developments in Magnesium Alloy Flammability Testing

2019-06-19
WIP
AIR6160A
This document provides informational background, rationale and a technical case to allow consideration of the removal of the magnesium alloy restriction in aircraft seat construction as contained in AS8049B. The foundation of this argument is flammability characterization work performed by the FAA at the William J. Hughes Technical Center (FAATC), Fire Safety Branch in Atlantic City, New Jersey, USA. The rationale and detailed testing results are presented along with flammability reports that have concluded that the use of specific types of magnesium alloys in aircraft seat construction does not increase the hazard level potential in the passenger cabin in a post-crash fire scenario. Further, the FAA has developed a lab scale test method, reference DOT/FAA/TC-13/52, to be used as a certification test, or method of compliance (MOC) to allow acceptability of the use of magnesium in the governing TSO-C127 and TSO-C39C.
Technical Paper

Event-Driven Simulation of Particle-Particle and Particle-Surface Collisions in Ice Crystal Icing

2019-06-10
2019-01-2014
This paper describes an event-driven simulation tool for predicting particle-particle and particle-surface interactions in ice crystal icing (ICI). A new accretion model which is much less empirical than existing models for predicting ICI accretion is also described. Unlike previous models, the new “gouge/bounce model” (GBM) differentiates between (erosion) losses resulting from particle bounce and those resulting from particle gouging. A bounce threshold based on the tangential Stokes number is used to calculate most of the bounce loss. The GBM also predicts ejecta velocities and directions, at least approximately, which is important because most of the mixed-phase mass flux impacting a surface actually bounces off or erodes existing material in ICI, thereby increasing the mass flux downstream.
Technical Paper

Analysis and Automated Detection of Ice Crystal Icing Conditions Using Geostationary Satellite Datasets and In Situ Ice Water Content Measurements

2019-06-10
2019-01-1953
Recent studies have found that high mass concentrations of ice particles in regions of deep convective storms can adversely impact aircraft engine and air probe (e.g. pitot tube and air temperature) performance. Radar reflectivity in these regions suggests that they are safe for aircraft penetration, yet high ice water content (HIWC) is still encountered. The aviation weather community seeks additional remote sensing methods for delineating where ice particle (or crystal) icing conditions are likely to occur, including products derived from geostationary (GEO) satellite imagery that is now available in near-real time at increasingly high spatio-temporal detail from the global GEO satellite constellation.
Technical Paper

ICICLE: A Model for Glaciated & Mixed Phase Icing for Application to Aircraft Engines

2019-06-10
2019-01-1969
High altitude ice crystals can pose a threat to aircraft engine compression and combustion systems. Cases of engine damage, surge and rollback have been recorded in recent years, believed due to ice crystals partially melting and accreting on static surfaces (stators, endwalls and ducting). The increased awareness and understanding of this phenomenon has resulted in the extension of icing certification requirements to include glaciated and mixed phase conditions. Developing semi-empirical models is a cost effective way of enabling certification, and providing simple design rules for next generation engines. A comprehensive ice crystal icing model is presented in this paper, the Ice Crystal Icing ComputationaL Environment (ICICLE). It is modular in design, comprising a baseline code consisting of an axisymmetric or 2D planar flowfield solution, Lagrangian particle tracking, air-particle heat transfer and phase change, and surface interactions (bouncing, fragmentation, sticking).
Journal Article

Process Regulations and Mechanism of WEDM of Combustor Material

2019-06-07
Abstract This study discusses the experimental investigation on WEDM of combustor material (i.e., nimonic 263). Experimentation has been executed by varying pulse-on time (Ton), pulse-off time (Toff), peak current (Ip), and spark gap voltage (Sv). Material removal rate (MRR), surface roughness (SR), and wire wear rate (WWR) are employed as process performance characteristics. Experiments are designed as per the box-Behnken design technique. Parametric optimization has also been performed using response surface methodology. Besides this, field-emission scanning electron microscope (FE-SEM) and an optical microscope are utilized to characterize WEDMed and worn-out wire surfaces. It is observed that both surfaces contain micro-cracks, craters, spherical droplets, and a lump of debris. Furthermore, the mechanism of recast layer formation has been critically evaluated to apprehend a better understanding of the technique. The key features of the experimental procedure are also highlighted.
Journal Article

High Power-Density, High Efficiency, Mechanically Assisted, Turbocharged Direct-Injection Jet-Ignition Engines for Unmanned Aerial Vehicles

2019-05-02
Abstract More than a decade ago, we proposed combined use of direct injection (DI) and jet ignition (JI) to produce high efficiency, high power-density, positive-ignition (PI), lean burn stratified, internal combustion engines (ICEs). Adopting this concept, the latest FIA F1 engines, which are electrically assisted, turbocharged, directly injected, jet ignited, gasoline engines and work lean stratified in a highly boosted environment, have delivered peak power fuel conversion efficiencies well above 46%, with specific power densities more than 340 kW/liter. The concept, further evolved, is here presented for unmanned aerial vehicle (UAV) applications. Results of simulations for a new DI JI ICE with rotary valve, being super-turbocharged and having gasoline or methanol as working fuel, show the opportunity to achieve even larger power densities, up to 430 kW/liter, while delivering a near-constant torque and, consequently, a nearly linear power curve over a wide range of speeds.
Standard

Oxygen Cylinder Installation Guide

2019-04-11
CURRENT
ARP5021B
This document provides guidance for oxygen cylinder installation on commerical aircraft based on airworthiness requirements, and methods practiced within aerospace industry. It covers considerations for oxygen systems from beginning of project phase up to production, maintenance, and servicing. The document is related to requirements of DOT-approved oxygen cylinders, as well to those designed and manufactured to standards of ISO 11119. However, its basic rules may also be applicable to new development pertaining to use of such equipment in an oxygen environment. For information regarding oxygen cylinders itself, also refer to AIR825/12.
Standard

Numerical Modeling Techniques for Jet Engine Test Cell Aerodynamics

2019-03-21
CURRENT
AIR6355
This SAE Aerospace Information Report (AIR) has been written for individuals associated with ground level testing of turbofan and turbojet engines, and particularly for those who might be interested in investigating steady-state performance characteristics of a new test cell design or of proposed modifications to an existing test cell by means of numerical modeling and simulation. It is not the intent of this standard to provide specific test cell design recommendations, which are covered in the reference documentation.
Journal Article

Thermal Analysis of Aircraft Auxiliary Power Unit: Application of Chemical Looping Combustion

2019-03-19
2019-01-1390
An “APU” (Auxiliary Power Unit) is a small gas turbine engine to provide supplementary power to an aircraft and is located at the tails of larger jets. APU generators provide auxiliary electrical power for running aircraft systems on the ground. Applications include powering environmental systems for pre-cooling or preheating the cabin, and providing power for crew functions such as preflight, cabin cleanup, and galley (kitchen) operation and long-haul airliners must be started using pneumatic power of APU compressor. The Honeywell 131-9A gas turbine APU has 440 kW shaft power and 90 kW electric generator consuming 120 kg fuel/hour. Here the traditional combustor of the APU is proposed to be replaced by a chemical-looping-combustion (CLC) system.
Article

SAE International releases new process for measuring aerosols in aircraft exhaust

2019-03-05
SAE International has published a new recommended practice for assessing the amount of nonvolatile particulate matter (nvPM) that exits aircraft engine exhaust nozzles – ARP6481: Procedure for the Calculation of Non-Volatile Particulate Matter Sampling and Measurement System Losses and System Loss Correction Factors
Standard

Supplemental Propulsion System Performance Station Designation

2019-01-03
CURRENT
AIR6508
This SAE Aerospace Information Report (AIR) supplements the AS755 performance station designation system for complex or unconventional propulsion cycles and their derivatives. The station numbering conventions presented herein are for use in all communications concerning propulsion system performance such as computer programs, data reduction, design activities, and published documents. They are intended to facilitate calculations by the program user without unduly restricting the method of calculation used by the program supplier. The contents of this document will follow AS755 and AS6502 where applicable. The list of symbols presented herein will be used for identification of input and output parameters. These symbols are not required to be used as internal parameter names within the engine subprogram.
Article

SAE International launches aerospace technology symposium at Japan Aerospace 2018

2018-11-26
SAE International, a global association committed to being the ultimate knowledge source for mobility engineering, is bringing together subject-matter experts from across the globe for the first SAE International Aerospace Japan Symposium, held November 29 and 30 in conjunction with Japan International Aerospace Exhibition 2018 at Tokyo Big Sight convention center in Tokyo.
X