Refine Your Search

Topic

Search Results

Standard

Radiator Caps and Filler Necks

2019-10-09
WIP
J164

This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.

Standard

Requirements for a COTS Assembly Management Plan

2019-04-22
WIP
EIA933C
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets; as well as other ADHP markets that wish to use this document.
Standard

Lift Capacity Calculation Method Scrap and Material Handlers

2019-04-15
CURRENT
J2518_201904
This SAE Standard provides a uniform method to calculate the lift capacity of scrap and material handlers, establishes definitions and specifies machine conditions for the calculations. This document applies to scrap and material handlers as defined in SAE J2506 that have a 360 degrees continuous rotating upper structure. It does not apply to equipment that is incapable of lifting a load completely off the ground. This document applies to those machines that are crawler, wheel, rail and pedestal or stationary mounted.
Standard

Telescopic Boom Length Indicating System

2019-02-15
CURRENT
J1180_201902
This SAE Recommended Practice applies to mobile cranes when used in lifting crane service which are equipped with boom length indicating devices.
Standard

Qualified Hoses for Marine Applications

2018-12-31
CURRENT
J1942/1_201812
The following list consists of hose data provided as of December 2018, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results.
Standard

Wiring Distribution Systems for Off-Road, Self-Propelled Work Machines

2018-11-21
CURRENT
J1614_201811
This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.
Standard

Specification Definitions - Hydraulic Backhoes

2018-11-14
CURRENT
J49_201811
This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors.
Standard

Radiator Caps and Filler Necks

2018-04-05
CURRENT
J164_201804
This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.
Standard

Safety Signs for Off-Road Work Machines

2018-03-23
CURRENT
J115_201803
SAE J115 specifies the relevant ISO standards for application to safety signs for use on off-road work machines as defined in SAE J1116.
Standard

Fifth Wheel and Gooseneck Attachment Performance Up to 13608/kg (30000/lb) Trailer Weight

2017-11-28
CURRENT
J2638_201711
This document establishes minimum performance criteria and definition of terms for the towing interface between a towing vehicle and fifth wheel or gooseneck trailer at or below 13608 kg (30000 pounds) gross trailer weight. This establishes criteria for the hitch, tow vehicle attachment structure, trailer attachment structure, and coupler.
Standard

Rating of Winches

2017-11-03
CURRENT
J706_201711
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.
Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2017-10-10
CURRENT
J444_201710
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
Standard

Headlamps for Industrial Equipment

2017-10-10
CURRENT
J95_201710
This SAE Standard provides performance and general design requirements and related test procedures for headlamps for use on industrial wheeled equipment that may be operated on public roads.
Standard

Crane Boomstop

2017-10-09
CURRENT
J220_201710
This SAE Recommended Practice applies to the boomstop for the main boom of all mobile construction type cranes having rope supported booms, equipped for hook work, clamshell, magnet, grapple, or concrete bucket attachments.
Standard

Dynamic Durability Testing of Seat Cushions for Off-Road Work Machines

2017-08-08
CURRENT
J1454_201708
This SAE Standard describes a laboratory test procedure for comparatively evaluating the durability and fatigue life qualities of a complete seat cushion by submitting the seating surface of the cushion to repetitive compressive and rotational loading with a simulated human buttocks.
X