Refine Your Search

Date

Date

Fasteners Truck and Bus Wheel Committee

Search Results

Viewing 1 to 20 of 52
123Next >Last >>
Sort by published
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2023-06-12
CURRENT
J1842_202306
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2023-05-19
CURRENT
J1671_202305
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Disc Wheel and Hub or Drum Interface Dimensions - Truck and Bus
2021-04-30
CURRENT
J694_202104
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for truck and bus applications. Disc wheels designed only for single wheel applications (not dual wheels) for light trucks and special or less common applications are not covered in this document.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2019-10-17
HISTORICAL
J1671_201910
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2019-10-07
CURRENT
J2535_201910
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles
2019-09-03
HISTORICAL
J2696_201909
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less-common applications are not covered.
Standard

Fastener Hardware for Wheels for Demountable Rims
2019-06-17
CURRENT
J1835_201906
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Wheels/Rims - Military Vehicles Test Procedures and Performance Requirements
2019-06-06
HISTORICAL
J1992_201906
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2018-08-08
HISTORICAL
J1842_201808
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2016-06-30
HISTORICAL
J1095_201606
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.500 to 13.189 in). It is up to each hub and/or wheel for demountable rims manufacturer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

Disc Wheel and Hub or Drum Interface Dimensions - Truck and Bus
2015-05-12
HISTORICAL
J694_201505
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for truck and bus applications. Disc wheels designed only for single wheel applications (not dual wheels) for light trucks and special or less common applications are not covered in this document.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2015-02-20
HISTORICAL
J1671_201502
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2014-02-03
HISTORICAL
J1842_201402
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Fastener Hardware for Wheels for Demountable Rims
2014-01-03
HISTORICAL
J1835_201401
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2013-02-11
HISTORICAL
J2535_201302
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles
2012-05-29
HISTORICAL
J2696_201205
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.
Standard

Wheels/Rims - Military Vehicles - Test Procedures and Performance Requirements
2012-04-23
HISTORICAL
J1992_201204
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
123Next >Last >>
X