Refine Your Search

Topic

Author

Affiliation

Search Results

Training / Education

FEA Beyond Basics Thermal Analysis

2019-12-16
Finite Element Analysis (FEA) is a powerful and well recognized tool used in the analysis of heat transfer problems. However, FEA can only analyze solid bodies and, by necessity thermal analysis with FEA is limited to conductive heat transfer. The other two types of heat transfer: convection and radiation must by approximated by boundary conditions. Modeling all three mechanisms of heat transfer without arbitrary assumption requires a combined use of FEA and Computational Fluid Dynamics (CFD).
Technical Paper

Low Voltage Powertrain in Light Electric Vehicles

2019-11-21
2019-28-2467
Engineering objective Light Electric Vehicles (LEV) with Li-ion batteries suffer from short battery life and poor efficiency, due to low grade electronics. Battery management systems (BMS) cannot always keep the pack in balance, and after cell voltages drift, capacity of the pack diminishes and some cells may destruct, causing a fire. The paper describes a novel approach to LEV powertrains using parallel connected battery cells & control methodology that keep cells in balance naturally, thereby eliminating BMS and hence safer to use. Li-Ion cells with different chemistries can be used and superior thermal management reduces temperature rise, resulting in longer battery life. Methodology Based on the original invention by the author, the system circuit schematics was designed and simulated using OrCAD PSpice. After obtaining results from the simulation, the first prototype device was constructed and tested in laboratory.
Technical Paper

Thermal Management of Li-Ion Battery Pack using GT-SUITE

2019-11-21
2019-28-2500
Objective It is very important to simulate the battery pack being built to understand its behavior when used in applications especially Electric vehicles (EV). All Li-Ion cells are not the same. They need to be characterized before building any battery pack. Hence modeling the battery pack to simulated its performance in the actual conditions becomes important. Methodology To understand the behavior of cells in the on-field environment, they are tested at various conditions like different rates of charging/discharging, various depth of discharge (DOD), ambient temperature, etc. HPPC test is also performed on cells to derive its RC model equivalent model. GT Suite simulation software is used to model the Li-Ion cell using the testing data. Depending on the pack configuration, the modeled cell is connected in the required series and parallel configuration, to study the battery pack with respect to aging, performance and cooling requirements.
Technical Paper

Electric Vehicle Thermal Management System For Hot Climate Regions

2019-11-21
2019-28-2507
ELECTRIC VEHICLE THERMAL MANAGEMENT SYSTEM FOR HOT CLIMATE REGIONS Rana Tarun*, Yamamoto Yuji, Kumar Ritesh, Bhagatkar Shubhada Pranav Vikas India Private Limited, India Key Words Electric Vehicles (EV); Battery Thermal Management System (BTMS); COP; Electric Vehicle Thermal Management System (EVTMS); BTMS and HVAC System Integration; Thermal System Performance Comparison; Active Liquid Cooling; EV Battery Cooling Research and/or Engineering Questions/Objective Electric Vehicles is the need of time to limit global warming and it is in application at a wide scale in colder or mild climate regions where ambient temperature is limited to mild or moderate level. Its application (Heat pump, CO2) is constrained to cold climates only due to securing better COP for heating function, sacrificing cooling COP of the existing system when operated in Hot Climate Regions, thus limiting its application to nearly half of the automotive user-base.
Technical Paper

Thermal Challenges in Automotive Exhaust System through Heat Shield Insulation

2019-11-21
2019-28-2539
While advanced automotive system assemblies contribute greater value to automotive safety, reliability, emission/noise performance and comfort, they are also generating higher temperatures that can reduce the functionality and reliability of thesystem over time. Thermal management and insulation are extremely important and highly demanding in BSVI, RDE and Non-IC engine operating vehicles. Passenger vehicle and Commercial vehicle exhaust systems are facing multiple challenges such as packaging constraints, weight reduction andthermalmanagement requirements.Frugal engineering is mandatory to develop heat shield in the exhaust system with minimum heat loss. The focus of the paper is to design, develop and validate heat shield products with different variables such as design gap, insulation material, sheet metal thickness and manufacturing processes. 1D and 3D computational simulations are performed with different gaps from 3 mm to 14 mm are considered.
Technical Paper

Replacing twin electric fan radiator with Single fan radiator

2019-11-21
2019-28-2381
Downsizing is one of the crucial activities being performed by every automotive engineering organization. The main aim is to reduce – Weight, CO2 emissions and achieve cost benefit. All this is done without any compromise on performance requirement or rather with optimization of system performance. This paper evaluate one such optimization, where-in radiator assembly with two electric fan is targeted for downsizing for small commercial vehicle application. The present two fan radiator is redesigned with thinner core and use of single fan motor assembly. The performance of the heat exchanger is tested for similar conditions back to back on vehicle and optimized to get the balanced benefit in terms of weight, cooling performance and importantly cost. This all is done without any modification in vehicle interface components except electrical connector for fan. The side members and brackets design is also simplified to achieve maximum weight reduction.
Technical Paper

Coupled Electro-Chemical and Thermal Modeling for Cylindrical Lithium-ion Batteries

2019-11-21
2019-28-2488
The shift over of the automobile sector from the ICE to the electric drives is imminent due to arising global issues of pollution and ever rising pressure on the demand of the natural resources due to lower efficiency of the ICE drives. This has led to uprising of the Lithium-ion batteries, with addition of the burden of living to expectation of clean energy and higher efficiencies. Alongside, with limitation in the availability of the lithium-ion batteries they carry a hefty price tag with them, hence causing huddles in the research. Lack of research leads to failure of batteries and may cause life threatening situations when operating in the vehicle. In order to insight the working of the cylindrical lithium-ion batteries under different driving and environmental conditions a methodology is developed for the coupled electro-chemical and thermal phenomenon. This allows anticipating the behaviour of the battery under different conditions that influence its performance.
Technical Paper

Miniaturized and sleek protective device

2019-11-21
2019-28-2535
A miniaturized and sleek protective device M. Priyanka, Mahindra&Mahindra, India D. Boobala Krishnan*, Mahindra&Mahindra, India T.Vijayan, Mahindra& Mahindra, India Keywords-Fuse, Lightweight. Research and/or Engineering Questions/Objective: Now-a-days there is lot of advancement coming in automobiles. Earlier the electronics were used in engine and engine compartment areas. Now all hydraulics and transmission have been operated by electronics. The role of electronics like sensors, actuators increasing day by day for lifting and moving operations. With increase in electronics circuit, there is complex in wiring harness and packaging space for fuse box is premium Limitations: Limitations of placing other devices. Occupy more space and weight in the vehicle. Packing constraint due to vibration and thermal management issues. Methodology: Two different fuse of same rating can be given in one fuse and we can reduce the wire size.
Training / Education

Introduction to Power Electronics in Automotive Applications

2019-11-04
Modern power electronics (PE) devices and circuits are now in widespread use in automotive and non-automotive applications. The purpose of this course is to give an overall introduction to the key aspects of power electronic circuits, components and design in automotive applications. Topics covered include power semiconductor devices, their characteristics and operation, and their use in power electronics circuits.
Technical Paper

A New Co-Simulation Approach for Tolerance Analysis on Vehicle Propulsion Subsystem

2019-09-09
2019-24-0079
An increasing demand for reducing cost and time effort of the design process via improved CAE (Computer-Aided Engineer) tools and methods has characterized the automotive industry over the past two decades. One of the main challenge regarded the effective simulation of a vehicle’s propulsion system dealing with different physical domains: several examples have been proposed in literature mainly based on co-simulation approach which involves a specific tool for each propulsion system part modeling. Nevertheless, these solutions are not fully suitable and effective to perform statistical analysis including all physical parameters. In this respect, this paper presents the definition and implementation of a new simulation methodology applied to a propulsion subsystem.
Technical Paper

Possibilities of Wall Heat Transfer Measurements at a Supercharged Euro IV Heavy-Duty Diesel Engine with High EGR-Rates, an In-cylinder Peak Pressure of 250 bar and an Injection Pressure up to 2500 bar

2019-09-09
2019-24-0171
A raise of efficiency is, especially for CV, the strongest selling point concerning the TCO. Accompanied by legislations, with contradictive development demands, satisfying solutions have to be found. The analysis of energy losses in modern engines shows three influencing parameters. The losses resulting from taking real gas properties and non-ideal combustion into account have only a limited potential for gains, wall heat losses are currently believed to have the highest optimization potential. Critical for the occurrence of these losses is the wall heat transfer, which can be described by coefficients. To reduce WHT accompanying losses a decrease of energy transfer between combustion gas and combustion chamber wall is necessary. A measurement of heat fluxes is needed to determine the WHT relations at the combustion chamber of an engine. Methods to reduce the WHT can be developed and their effectiveness can be evaluated.
Technical Paper

Validation and Analysis of Heat Losses Prediction Using Conjugate Heat Transfer Simulation for an Internal Combustion Engine

2019-09-09
2019-24-0091
New technologies are required to improve engine thermal efficiency. For this it is necessary to use all the tools available nowadays, in particular computational tools, which allow testing the viability of different solutions at reduced cost. In addition, numerical simulations often provide more complete and precise information than experimental tests. Such is the case for the study of the heat transfer through the walls of an engine. Conjugate Heat Transfer (CHT) simulations permit precise calculations of the heat transfer rate from gas to walls throughout the whole engine cycle, and thus it is possible to know such details as the instantaneous heat losses and wall temperature distribution on the walls, which no experiment can give. Nevertheless, it is important to validate CHT calculations, either with some experimental measurements or with some other reliable tool, such as 0D-1D modelling known to work well.
Technical Paper

A practical Recuperated Split Cycle engine for low emissions and high efficiency

2019-09-09
2019-24-0190
The Recuperated Split Cycle Engine is a new type of ICE, offering a step change in efficiency and tailpipe emissions. It targets the heavy duty, long-haul sector (trucks, rail, shipping), where electrification is most challenging, and distributed generation, where capacity is required to support rising electrification. The engine separates cold (induction, compression) and hot (combustion, expansion) parts of the cycle; waste exhaust heat is recovered between them via a recuperator, as in a recuperated gas turbine. Recent research presented in another paper at this conference shows that the sonic airflows seen in the induction event give rise to extraordinary fuel mixing and clean, cool combustion, with potential for after-treated emission levels between SULEV and zero-impact (either unmeasurable or below ambient). However, recuperation and thermal insulation of the hot cylinder also enable high thermal efficiency, with a much flatter efficiency map than a conventional ICE.
Technical Paper

A Novel 1D Co-Simulation Framework for the Prediction of Tailpipe Emissions Under Different IC Engine Operating Conditions

2019-09-09
2019-24-0147
The prediction of the pollutants emitted by internal combustion engines during driving cycles has been a challenge since the introduction of the emission regulation legislation. During the last decade, along with the more tightening limits and increased public concern about the matter of air quality, the possibility of simulating various driving tests with cost effective computing facilities has become a key feature for modern simulation codes. Many 1D simulation tools are available on the market, offering real time models capable of achieving the simulation of any driving cycle in limited time frames. These approaches are based on the extreme simplification of the engine geometry and on the adoption of engine maps, which, for any engine operating condition, give the engine output in terms of power, or torque, and of exhaust gas composition.
Technical Paper

A Proposed Diesel Powertrain to Meet Future Emission Standards and Achieve High Engine Efficiency

2019-09-09
2019-24-0191
Nowadays, powertrain development activity is performed on the base of fulfilling the stricter emission standards under real driving conditions (RDE). However, the pressure on automotive industry to reduce CO2 emissions in high efficient diesel applications results in lower exhaust gas temperatures. Therefore, it is highly needed to develop advanced vehicle thermal management methods to both fulfil the targets of emission standards and high thermal efficiency, without increasing dramatically the powertrain cost. The aim of this work is to experimentally demonstrate that by utilising advanced engine and ATS control methods and revising the engine hardware and subsystems can lead to significant improvement on the fuel efficiency and emissions of the conventional diesel powertrain. The revised engine includes an improved combustion system, completely revised turbocharging and air handling system whilst being heavily reworked with respect to FMEP reduction.
Technical Paper

Experimental Investigation on the Use of Argon to Improve FMEP Determination Through Motoring Method

2019-09-09
2019-24-0141
Mechanical friction is still one of the current topics in internal combustion engine research and development. In the ever increasing challenge of developing more efficient and less polluting engines, friction reduction is of significant importance; whose investigation needs an accurate and reliable measurement technique. The Pressurized Motoring method is one of the techniques used for both friction and heat transfer measurements in internal combustion engines. This method is able to simulate mechanical loading on the engine components similar to the fired conditions. It also allows measurement of friction mean effective pressure (FMEP) with a much smaller uncertainty as opposed to that achieved from a typical firing setup. Despite its advantages, this method of FMEP determination is usually criticized over the fact that the thermal conditions imposed in pressurized motoring are far detached from those seen in fired conditions, hence not able to simulate the complete effects on FMEP.
Technical Paper

Study of Friction Optimization Potential for Lubrication Circuits of Light-duty Diesel Engines

2019-09-09
2019-24-0056
Over the last two decades, engine research has been mainly focused on reducing fuel consumption in view of compliance with stringent homologation targets and customer expectations. As it is well known, the objective of overall engine efficiency optimization can be achieved only through the improvement of each element of the efficiency chain, of which mechanical constitutes one of the two key pillars (together with thermodynamics). In this framework, the friction reduction for each mechanical subsystems has been one of the most important topics of modern diesel engine development. In particular, the present paper analyzes the lubrication circuit potential as contributor to the mechanical efficiency improvement, by investigating the synergistic impact of oil circuit design, oil viscosity characteristics (including new ultra-low formulations) and thermal management. For this purpose, a combination of theoretical and experimental tools were used.
Technical Paper

Dynamic Thermal Behavior of a GDI Spray Impacting on a Heated Thin Foil by Phase-Averaged Infrared Thermography

2019-09-09
2019-24-0036
The regulations about pollutant emissions imposed by Community’s laws encourage the investigation on the combustion optimization in modern engines and in particular in those adopting the gasoline direct injection (GDI) or direct injection spark-ignited (DISI) configuration. It is known that the piston head and cylinder surface temperatures, coupled with the fuel injection pressure, strongly influence the interaction between droplets of injected fluid and the impinged wall. In the present study, the Infrared (IR) thermography is applied to investigate the thermal footprint of an iso-octane spray generated by a multi-hole GDI injector impinging on a heated thin foil. The experimental apparatus includes an Invar foil (50 μm in thickness) heated by Joule effect, clamped within a rigid frame, and the GDI injector located 11 mm above the surface.
Technical Paper

Oxy-Fuel HCCI Combustion in a CFR Engine with Carbon Dioxide as a Thermal Buffer

2019-09-09
2019-24-0119
A basic formula inspired by the Otto engine cycle shows that the thermodynamic efficiency of the engine increases as the mixture specific heat ratio and compression ratio increase. Homogenous charge compression ignition (HCCI) engines allow the combustion of a lean mixture at relatively higher compression ratios increasing the thermodynamic efficiency. At the same time, it is also a low temperature combustion and this means lower NOx emissions. One way to increase the thermodynamic efficiency of the engine is to increase the specific heat ratio by replacing the nitrogen in the oxidizer by a monoatomic gas that has the highest possible specific heat ratio. However, higher specific heat ratio results in elevated cylinder temperature and pressure leading to engine knock. The compression ratio is thus decreased to avoid this phenomenon. Also, elevated engine temperature will oxidize any nitrogen (no matter how small) forming undesired NOx emissions.
Technical Paper

Temperature Measurements of the Piston surface in a Research Compression Ignition Engine in Transient Conditions for 1d Model of Heat Transfer

2019-09-09
2019-24-0182
Analysis of heat losses in internal combustion engines (ICEs) is fundamental to evaluate and improve the engine efficiency. Detailed and reliable heat transfer models are required for more complex 1d-3d combustion models. At the same time, the thermal status of engine components, as pistons, is needed for an efficient design. Measurements of piston temperature during ICEs operation represent a precious and challenging result to get for the aforementioned purposes. In previous works, the authors, first, evaluated and, then, measured the temperature of the optical window in a research compression ignition engine via thermal imaging and thermocouple installation, respectively. The tests concerned steady state and transient conditions.
X