Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

A review on influence of different flushing methods on Material Removal Rate using EDM.

2019-11-21
2019-28-2543
Electrical release machining (EDM), is a material removal procedure whereby a coveted shape is acquired by utilizing electrical releases (sparks). Material is expelled from the work piece by a progression of quickly repeating current releases between cathode and anode, isolated by a dielectric fluid and subject to an electric voltage. At the point when the voltage between the two terminals is expanded, the power of the electric field in the volume between the anodes winds up more prominent than the quality of the dielectric (in any event in a few spots), which separates, enabling current to stream between the two cathodes. This wonder is the equivalent as the breakdown of a capacitor (condenser). Accordingly, material is expelled from the cathodes.
Technical Paper

Automobile Exhaust Emmision Control- A review

2019-11-21
2019-28-2382
Since the 20th century increase in the number of cars in the major cities is been a point of concern because of the toxic gasses being emitted from the engine of an automobile. These gasses are polluting the atmosphere and degrading the air to breathe. The main gasses responsible for the degradation of air quality are carbon monoxide, hydrocarbon and oxides of nitrogen. There is a necessity to find ways to reduce the pollution emitted into the atmosphere from the automobile. The source of emission is either evaporation from fuel tank or carburetor which is easy to be dealt with or harmful gasses due to improper combustion which is a concern for the environment. The two ways to reduce these emissions are, modification in the engine to minimize the production of harmful gases and to treat the harmful gasses emitted from the engine before blowing it into the atmosphere from the exhaust. Catalysts help to break harmful gasses into smaller compounds that are environment-friendly.
Technical Paper

EMISSION REDUCTION OF A DIESEL ENGINE FUELED WITH BLENDS OF BIOFUEL UNDER THE INFLUENCE OF 1,4-DIOXANE AND RICE HUSK NANO PARTICLE.

2019-11-21
2019-28-2387
Research Objectives. In this modern era increase in Pollution became a huge impact in the lives of all living creatures, in this automobile tends to be one of the major contributors in terms of air pollution thanks to their exhaust emissions. The objective of the present study is to reduce the amount of harmful pollutants emitted from the automobiles by the utilization of a biofuel further influenced by two additives (liquid and a Nano additive). Methodology In this study, first the bio oil is extracted, Then the biofuel is mixed with diesel fuel at different proportions of 20%, 40% by volume. Experiments are carried out in a direct injection compression ignition engine, which is a stationary test engine manufactured by Kirloskar, connected to a computer setup. The emission values in the exhaust gases are obtained using AVL exhaust gas analyzer.
Technical Paper

Engine Fuel Economy Optimization for different Hybrid Architectures using 1-D Simulation technique

2019-11-21
2019-28-2496
In order to improve fuel economy of the 3.3 litre tractor model, various kinds of engine hybridization is studied. This paper presents a methodology to predict engine fuel consumption using 1-D software by coupling Ricardo Wave and Ricardo Ignite. Engine fuel consumption and emission maps are predicted using Ricardo WAVE. These maps are used as an input to IGNITE for predicting cumulative fuel consumption. There is good agreement within 10% deviation between simulated cumulative fuel consumption and experimental cumulative fuel consumption. Same calibrated model is used further for studying series hybridization, parallel P1 type and Parallel P2 type of hybridization. A design of experiment (DOE) model is run for different electric motor sizes, battery capacity and battery state of charge condition, to understand their effects on overall engine fuel consumption and cycle soot emission. Model predicts overall significant reduction in cumulative fuel consumption and soot emission.
Technical Paper

Development of Dedicated Lubricant for Hydrogen Fueled Spark Ignition Engine

2019-11-21
2019-28-2511
Hydrogen has low ignition energy ensures easy ignition of the ultra-lean mixture of H2+air also. The flame speed of hydrogen is about five times higher than methane and gasoline which allows hydrogen fuelled IC engines to have relatively reduced cyclic variations than that of with methane and gasoline. High flame speed also helps to make the combustion closer to constant volume which enhances the thermal efficiency of hydrogen fuelled IC engine. High octane number of hydrogen makes it suitable for its application in Spark ignition (SI) engines. Since the hydrogen combustion in spark ignition engine generates water which can interfere with the lubricant performance, different lubricant is to be developed for this purpose. In this background, the present work is aimed at the development of dedicated lubricant for hydrogen fuelled SI engine. This paper presents the various parameters required for evaluating different lubricants for hydrogen fuelled genset.
Technical Paper

Development of Diesel Particulate NOx Reduction DPNR System for Simultaneous Reduction of PM and NOx in Diesel Engines

2019-11-21
2019-28-2554
The Diesel Particulate NOx Reduction (DPNR) system is used for simultaneous reduction of PM and NOx in diesel engine. DPF is used to trap particulate matter in diesel engines. NOx absorber technology removes NOx in a lean (i.e. oxygen rich) exhaust environment for both diesel and gasoline lean-burn GDI engines. The NOx storage and reduction catalyst is uniformly coated on the wall surface and in the fine pores of a highly porous filter substrate. Combination of these two components in the DPNR results in a compact size of the system. The base diesel engine model validated with pressure crank angle diagram and performance parameters such as Indicated mean effective pressure. This base engine’s exhaust emission is given as an input to the DPNR system. The surface reaction is connected to the DPF through chemcon template. The surface reaction is NOx storage and reduction chemical kinetics like Lean NOx Trap. The modelling of DPNR and Base engine is done using GT-SUITE.
Technical Paper

Design and Development of Constant speed diesel engine up to 20 bar BMEP with Inline FIS

2019-11-21
2019-28-2549
Design and Development of Constant speed diesel engine up to 20 bar BMEP with Inline FIS Remesan CB, Sanjay Aurora, Vasundhara V Arde, Vishal Kumar, Om Prakash Yadav, Piyush Ranjan Eicher Engines (A unit of TAFE Motors & Tractors Ltd.) Abstract Development trend in diesel engine is to achieve more power from same size of engine. With increase in brake mean effective pressure (BMEP), the peak firing pressure will also increase. The methodology to control the peak firing pressure on higher BMEP is the major challenge. We achieved better SFC with CPCB II emission targets on a constant speed engine. This study involves a systematic approach to optimize combustion parameters with a cost effective and robust inline Fuel Injection System. This paper deals with the strategies applied and experimental results for achieving the power density of 25kW/lit with Inline FIP by keeping lower Peak firing pressure.
Technical Paper

FABRICATION AND WEAR CHARACTERISTICS BASALT FIBER REINFORCED POLYPROPYLENE MATRIX COMPOSITES

2019-11-21
2019-28-2570
Generally brake pads are manufacturing by use of asbestos materials, these materials are chemically harmful and toxic, affects human health. The present investigation fabricates polypropylene composites with mixing constant volume [5 Vol.%] of alumina nano particles and different volume percentages [0%, 5%, 10% & 15%] of basalt fibre by hand layup compression technique. The wear characteristics of polypropylene matrix composites were tested by dry sliding condition using pin on disc apparatus configuration with hardened steel counter-face at elevated temperature. The load was applied 30N to 70N with the interval of 20N and varying of sliding speed 300 rpm to 900rpm with the interval of 300rpm for the time period of 0-180 sec. The wear rate was decreases with addition of alumina nano particle and also increases the frictional force for the effect of basalt fibre content present in the composites. The co-efficient of friction was increases from 0.1 to 0.66 under normal loading condition.
Technical Paper

Development of high power density diesel engine for constant speed application

2019-11-21
2019-28-2566
Engine up gradation for higher power rating involves challenges that require hardware changes which not only increase cost but also demand higher space. This paper focuses on the up gradation of a 4 cylinder 4.9l CRDi engine from 24.03 kW/L to 30.75 kW/L by adjustment of various parameters to meet both emission and performance targets. Various challenges like higher exhaust temperature, increased peak firing pressure etc. were met using the proper calibration strategy. To meet SFC targets and keep peak firing pressures, exhaust temperatures within desired limits, different operating points for EGR, main injection timing, rail pressure have been optimized. The operating points for optimization were determined by conducting various drive trials on different type of load conditions in test bench. Calibration strategy involved the safe limits of NOx, soot, CO emissions, fuel consumption.pfp, and exhaust temperature.
Technical Paper

Combustion Optimization and In-cylinder NOx and PM Reduction by using EGR and Split Injection Technique

2019-11-21
2019-28-2560
Nowadays, the major most challenge in the diesel engine is the oxides of nitrogen (NOx) and particulate matter (PM) trade-off, with minimal reduction in Power and BSFC. Modern day engines also rely on expensive after-treatment devices, which may decrease the performance and increase the BSFC. In this paper, combustion optimization and in-cylinder emission control by introducing the Split injection technique along with EGR is carried out by 1-D (GT-POWER) simulation. Experiments were conducted on a 3.5 kW Single-cylinder naturally aspirated CRDI engine at the different load conditions. The Simulation model incorporates detailed pressure (Burn rate) analysis for different cases and various aspects of ignition delay, premixed and mixing controlled combustion rate, the injection rate affecting oxides of nitrogen and particulate matter.
Technical Paper

Experimental investigations on CO2 recovery from petrol engine exhaust using adsorption technology

2019-11-21
2019-28-2577
Energy policy reviews state that automobiles contribute 25% of the total Carbon-di-oxide (CO2) emission. The current trend in emission control techniques of automobile exhaust is to reduce CO2 emission. We know that CO2 is a greenhouse gas and it leads to global warming. Conversion of CO2 into carbon and oxygen is a difficult and energy consuming process when compared to the catalytic action of catalytic converters on CO, HC and NOX. The best way to reduce it is to capture it from the source, store it and use it for industry applications. To physically capture the CO2 from the engine exhaust, adsorbents like molecular sieves are utilized. When compared to other methods of CO2 separation, adsorption technique consumes less energy and the sieves can be regenerated, reused and recycled once it is completely saturated. In this research work, zeolite X13 was chosen as a molecular sieve to adsorb CO2 from the exhaust.
Training / Education

Designing On-Board Diagnostics for Light and Medium Duty Emissions Control Systems

2019-11-11
On-board diagnosis of engine and transmission systems has been mandated by government regulation for light and medium vehicles since the 1996 model year. The regulations specify many of the detailed features that on-board diagnostics must exhibit. In addition, the penalties for not meeting the requirements or providing in-field remedies can be very expensive. This course is designed to provide a fundamental understanding of how and why OBD systems function and the technical features that a diagnostic should have in order to ensure compliant and successful implementation.
Technical Paper

Effect of Fuel Type and Tip Deposits on Gasoline Direct Injection Fuel Injector End of Injection Spray Characteristics

2019-10-28
2019-01-2600
There has been a great effort expended in identifying causes of Hydro-Carbon (HC) and Particulate Matter (PM) emissions resulting from poor spray preparation, leading to characterization of fueling behavior near nozzle. It has been observed that large droplet size is a primary contributor to HC and PM emission. Imaging technologies have been developed to understand the break-up and consistency of fuel spray. However, there appears to be a lack of studies of the spray characteristics at the End of Injection (EOI), near nozzle, in particular, the effect that tip deposits have on the EOI characteristics. Injector tip deposits are of interest due to their effect on not only fuel spray characteristics, but also their unintended effect on engine out emissions. Using a novel imaging technique to extract near nozzle fuel characteristics at EOI, the impact of tip deposits on Gasoline Direct Injection (GDI) fuel injectors at the EOI is being examined in this work.
Technical Paper

Assessing the Combined Outcome of Rice Husk Nano Additive and Water Injection Method on the Performance, Emission and Combustion Characters of the Low Viscous Pine Oil in a Diesel Engine

2019-10-28
2019-01-2604
The research work intends to assess the need and improvement of using a low viscous bio oil, RH (Rice Husk) Nano Particles and water injection method in enhancing the performance, emission and combustion characters of a diesel engine. One of the major setbacks for using biodiesel was its higher viscosity. Hence, a low viscous oil (Pine oil) which doesn’t need transesterification process was used as a biofuel in this study. To further improve its characteristics a non-metallic Nano additive produced from rice husk was added at 3 proportions (50, 100, 200 ppm) and the optimal quantity was found as 100ppm based on the BTE (brake thermal efficiency) value of 30.2% at peak load condition. This efficiency value was accompanied by a considerable decrease in pollutants like HC (Hydrocarbon), Smoke, CO (Carbon monoxide). On the contrary NOx (Oxides of Nitrogen) emission was found to be increased for all load values.
Training / Education

Emissions-Related OBD Systems A Design Overview

2019-09-20
On-board diagnostics, required by governmental regulations, provide a means for reducing harmful pollutants into the environment. Since being mandated in 1996, the regulations have continued to evolve and require engineers to design systems that meet strict guidelines. This one day seminar is designed to provide an overview of the fundamental design objectives and the features needed to achieve those objectives for generic on-board diagnostics. The basic structure of an on-board diagnostic will be described along with the system definitions needed for successful implementation.
Technical Paper

The benefits of using Composite Bearings in Aircraft Shock Absorbers

2019-09-16
2019-01-1898
This paper will use actual examples from aircraft recently introduced into service, to describe the main advantages of changing from the currently used metallic bearings, to composite bearings. Abstract: The introduction of composite bearing in a recently introduced twin aisle aircraft has resulted in: • Weight saving, by replacing bronze bearings with plastic bearings • Lowering of the particle count in the shock absorber oil, (Reduced contamination with metal particles) leading to reduced wear on seals and bearings. Qualification testing showed that Composite Bearings are able to provide longer service life than bronze bearings.
Technical Paper

Numerical investigation of Electrostatic Spray Painting Transfer Processes for vehicle Coating

2019-09-16
2019-01-1856
In this study we examined numerically the electrostatic spray transfer processes in the rotary bell spray applicator, which is this case implemented in a full 3D representation. The algorithm implemented and developed for this simulation includes airflow, spray dynamics, tracking of paint droplets and an electrostatic modularized solver to present atomization and in-flight spray phenomena for the spray forming procedure. The algorithm is implemented using the OpenFOAM package. The shaping airflow is simulated via an unsteady 3D compressible Navier-Stokes method. Solver for particle trajectory was developed to illustrate the process of spray transport and also the interaction of airflow and particle that is solved by momentum coupling. As the numerical results in this paper indicates dominant operating parameter voltage setting, further the charge to mass ratio and air-paint flow rate deeply effect the spray shape and the transfer efficiency (TE).
Technical Paper

Design of Experiments for Effects and Interactions During Brake Emissions Testing Using High-Fidelity Computational Fluid Dynamics

2019-09-15
2019-01-2139
The investigation and measurement of particle emissions from foundation brakes require the use of a special adaptation of inertia dynamometer test systems. To have proper measurements for particle mass and particle number, the sampling system needs to minimize transport losses and reduce residence times inside the brake enclosure. Existing models and spreadsheets estimate key transport losses (diffusion, turbophoretic, contractions, gravitational, bends, and sampling isokinetics). A significant limitation of such models is the inability to assess the complex turbulent flows and associated particle dynamics inside the brake enclosure, which is anticipated to be important. This paper presents a Design of Experiments (DOE) approach using Computational Fluid Dynamics (CFD) to predict the flow within a dynamometer enclosure under relevant operating conditions. The systematic approach allows the quantification of turbulence intensity, mean velocity profiles, and residence times.
Technical Paper

Real Driving Emissions Measurement of Brake Dust Particles

2019-09-15
2019-01-2138
The measurement of brake dust particles is a complex challenge owing to its open system configuration; indeed, the emitted particles are directly spread into the environment. The aim of the measurement is to compare the brake with other particle emitters, especially the combustion engines. Measurements on the inertia brake dyno feature controllable and reproducible environmental and load parameters. Although Real Driving Emission (RDE) measurements enable the detection of brake dust particles emitted in real driving conditions, they are complex and not reproducible due to external, continuously changing parameters (e.g., flow conditions, changing traffic conditions, particulate matter from other sources). The motivation lies in developing an RDE sampling system for particulate brake emissions, which meets the quality requirements of the measurements, as well as the prevention of particle losses and contamination, thereby supplementing and reviewing laboratory-based procedures.
X