Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Automobile Exhaust Emmision Control- A review

2019-11-21
2019-28-2382
Since the 20th century increase in the number of cars in the major cities is been a point of concern because of the toxic gasses being emitted from the engine of an automobile. These gasses are polluting the atmosphere and degrading the air to breathe. The main gasses responsible for the degradation of air quality are carbon monoxide, hydrocarbon and oxides of nitrogen. There is a necessity to find ways to reduce the pollution emitted into the atmosphere from the automobile. The source of emission is either evaporation from fuel tank or carburetor which is easy to be dealt with or harmful gasses due to improper combustion which is a concern for the environment. The two ways to reduce these emissions are, modification in the engine to minimize the production of harmful gases and to treat the harmful gasses emitted from the engine before blowing it into the atmosphere from the exhaust. Catalysts help to break harmful gasses into smaller compounds that are environment-friendly.
Technical Paper

Effect of Gasoline-Ethanol blends and CNG on GDI engine to reduce cost of vehicle ownership

2019-11-21
2019-28-2379
A major challenge for combustion development is to optimize the engine for improved fuel economy, reduce greenhouse gases. Stringent CAFÉ and emission norms require the customer to pay higher capital on vehicles. To offset the cost of ownership- cheaper and alternative energy sources are being explored. Ethanol blend with regular Gasoline and CNG are such alternative fuels. The study was carried on turbo-charged gasoline direct injection engine. The effect of ethanol on engine and vehicle performance is estimated and simulated numerically. The work is split into three stages: first the base 1D engine performance model was calibrated to match the experimental data. In parallel, vehicle level Simulink model was built and calibrated to match the NEDC cycle performance. Second, the thermal efficiency of the ethanol blend is calculated as a linear function of theoretical Otto cycle efficiency.
Technical Paper

CNG injector performance analysis against variation of physical and electrical parameters: An alternate fuel approach

2019-11-21
2019-28-2389
Authors: Udit Kaul, Mahendarpal and Madhusudan Joshi Organization: International Centre for Automotive Technology, Manesar Introduction: In this paper, a study concerning multi-point CNG injectors (MPCI) or commonly known as injector rail would be presented. Here we would make a detailed analysis regarding the performance of MPCIs due to variation in physical and electrical parameters. In this case multiple MPCIs would be considered and there electrical and dimension parameters would be compared with respect to their performance. The performance comparison would be done based on the common compliance standard under standard laboratory conditions. We would also like to propose the optimal combination of electrical and dimension parameters for better performance. The variables to be considered for the proposed study are: injector valve open/shut timing, injector dimension, voltage levels, solenoid types etc. Key words : multi-point CNG injectors, injector valve, solenoid
Technical Paper

Approach for CO2 Reduction in India’s Automotive Sector

2019-11-21
2019-28-2388
India has gone through a lot of transformation over the last decade. Today it is the 6th largest and one of the fastest growing economies in the world. Rising income level, increased consumerism, rapid growth in urbanization and digitization have attributed to this change. Government focus on “Make in India” for promoting trade and investment in India have ensured that India emerge as one of the largest growing economies in the world. The automotive industry played a pivotal role in the manufacturing sector to boost economic activities in India. The passenger car market has increased 3 times over the last decade and it has led to increased mobility options for many people across India. However, this has put concerns on the country’s energy security and emission levels. According to IEA’s recent report on global CO2 emission, 32.31 Gt of CO2 emissions were from fuel combustion in 2016, out of which transport sector contributed ~25%.
Technical Paper

A Technical Review on Performance and Emissions of Compressed Natural Gas – Diesel Dual Fuel Engine

2019-11-21
2019-28-2390
In view of the depletion of energy and environmental pollution, dual fuel technology has caught the attention of researchers as a viable technology keeping in mind the increased availability of fuels like Compressed Natural Gas (CNG). It is an ecologically friendly technology due to lower PM and smoke emissions and retains the efficiency of diesel combustion. Generally, dual fuel technology has been prevalent for large engines like marine, locomotive and stationary engines. However, its use for automotive engines has been limited in the past due to constraints of the limited supply of alternative fuels. CNG is a practical fuel under dual-fuel mode operation, with varying degree of success. The induction method prevents a premixed natural gas-air mixture, minimizes the volumetric efficiency and results in a loss of power at higher speeds.
Technical Paper

Study of Handling Behavior of a Passenger Vehicle after addition of CNG Tank

2019-11-21
2019-28-2405
Objective The objective of this paper is to achieve a comparable handling performance from a vehicle fitted with a CNG tank to that of its gasoline counterpart. A validated CarSim model is run through standard handling evaluation tests before and after the addition of CNG tank. The simulation results are used to compare the handling characteristics of the CNG vehicle with the Base vehicle. Further these results are used to tune the suspension parameters to find an optimum set-up for the actual CNG vehicle. The final parameters are then evaluated in the actual vehicle to verify the study. Methodology A mix of Actual Mule vehicle testing backed by quik Car Sim Model. Full car model is first developed using CarSim by using the parameters of the actual base gasoline vehicle. The modeled vehicle is then tested for standard handling maneuvers such Double Lane Change, Constant Radius Constant Speed and Pulse Input.
Technical Paper

Challenges of fuel economy determination with gaseous fuels

2019-11-21
2019-28-2512
The importance of fuel economy (FE) has significantly increased for new technologies like hydrogen fuel cells or compressed natural gas (CNG) engines. Regarding conventional combustion engine driven vehicles, the current gap between the official CO2 emissions and the real-world emissions on the road is quite big. One main reason for this gap might be a non-authentic test environment for combustion engines in comparison to real road conditions. New standards like the world harmonized driving cycle (WLTC) try to reduce the above-mentioned gap. Such standards underline the importance of complex speed and torque profiles. It appears that steady state consumption measurement is not sufficient anymore. Replacing the conventional vehicle engine by a fuel cell system does not eliminate this performance requirements on the measurement equipment. Performance testing methods are well known for conventional liquid fuels. However, new media like hydrogen or CNG represent new challenges.
Technical Paper

Design and Development of Constant speed diesel engine up to 20 bar BMEP with Inline FIS

2019-11-21
2019-28-2549
Design and Development of Constant speed diesel engine up to 20 bar BMEP with Inline FIS Remesan CB, Sanjay Aurora, Vasundhara V Arde, Vishal Kumar, Om Prakash Yadav, Piyush Ranjan Eicher Engines (A unit of TAFE Motors & Tractors Ltd.) Abstract Development trend in diesel engine is to achieve more power from same size of engine. With increase in brake mean effective pressure (BMEP), the peak firing pressure will also increase. The methodology to control the peak firing pressure on higher BMEP is the major challenge. We achieved better SFC with CPCB II emission targets on a constant speed engine. This study involves a systematic approach to optimize combustion parameters with a cost effective and robust inline Fuel Injection System. This paper deals with the strategies applied and experimental results for achieving the power density of 25kW/lit with Inline FIP by keeping lower Peak firing pressure.
Technical Paper

Development of high power density diesel engine for constant speed application

2019-11-21
2019-28-2566
Engine up gradation for higher power rating involves challenges that require hardware changes which not only increase cost but also demand higher space. This paper focuses on the up gradation of a 4 cylinder 4.9l CRDi engine from 24.03 kW/L to 30.75 kW/L by adjustment of various parameters to meet both emission and performance targets. Various challenges like higher exhaust temperature, increased peak firing pressure etc. were met using the proper calibration strategy. To meet SFC targets and keep peak firing pressures, exhaust temperatures within desired limits, different operating points for EGR, main injection timing, rail pressure have been optimized. The operating points for optimization were determined by conducting various drive trials on different type of load conditions in test bench. Calibration strategy involved the safe limits of NOx, soot, CO emissions, fuel consumption.pfp, and exhaust temperature.
Technical Paper

Combustion Optimization and In-cylinder NOx and PM Reduction by using EGR and Split Injection Technique

2019-11-21
2019-28-2560
Nowadays, the major most challenge in the diesel engine is the oxides of nitrogen (NOx) and particulate matter (PM) trade-off, with minimal reduction in Power and BSFC. Modern day engines also rely on expensive after-treatment devices, which may decrease the performance and increase the BSFC. In this paper, combustion optimization and in-cylinder emission control by introducing the Split injection technique along with EGR is carried out by 1-D (GT-POWER) simulation. Experiments were conducted on a 3.5 kW Single-cylinder naturally aspirated CRDI engine at the different load conditions. The Simulation model incorporates detailed pressure (Burn rate) analysis for different cases and various aspects of ignition delay, premixed and mixing controlled combustion rate, the injection rate affecting oxides of nitrogen and particulate matter.
Technical Paper

Experimental investigations on CO2 recovery from petrol engine exhaust using adsorption technology

2019-11-21
2019-28-2577
Energy policy reviews state that automobiles contribute 25% of the total Carbon-di-oxide (CO2) emission. The current trend in emission control techniques of automobile exhaust is to reduce CO2 emission. We know that CO2 is a greenhouse gas and it leads to global warming. Conversion of CO2 into carbon and oxygen is a difficult and energy consuming process when compared to the catalytic action of catalytic converters on CO, HC and NOX. The best way to reduce it is to capture it from the source, store it and use it for industry applications. To physically capture the CO2 from the engine exhaust, adsorbents like molecular sieves are utilized. When compared to other methods of CO2 separation, adsorption technique consumes less energy and the sieves can be regenerated, reused and recycled once it is completely saturated. In this research work, zeolite X13 was chosen as a molecular sieve to adsorb CO2 from the exhaust.
Training / Education

Designing On-Board Diagnostics for Light and Medium Duty Emissions Control Systems

2019-11-11
On-board diagnosis of engine and transmission systems has been mandated by government regulation for light and medium vehicles since the 1996 model year. The regulations specify many of the detailed features that on-board diagnostics must exhibit. In addition, the penalties for not meeting the requirements or providing in-field remedies can be very expensive. This course is designed to provide a fundamental understanding of how and why OBD systems function and the technical features that a diagnostic should have in order to ensure compliant and successful implementation.
Training / Education

Emissions-Related OBD Systems A Design Overview

2019-09-20
On-board diagnostics, required by governmental regulations, provide a means for reducing harmful pollutants into the environment. Since being mandated in 1996, the regulations have continued to evolve and require engineers to design systems that meet strict guidelines. This one day seminar is designed to provide an overview of the fundamental design objectives and the features needed to achieve those objectives for generic on-board diagnostics. The basic structure of an on-board diagnostic will be described along with the system definitions needed for successful implementation.
Technical Paper

Exhaust Purification Performance Enhancement by Early Activation of Three Way Catalysts for Gasoline Engines Used in Hybrid Electric Vehicles

2019-09-09
2019-24-0148
Three-way catalyst (TWC) converters are used to purify the toxic substances such as carbon monoxide (CO), nitrogen oxides (NOx), and hydrocarbons (HC) emitted from gasoline engines. However, a large amount of emissions could be emitted before the TWC reaching its light-off temperature during cold start. For hybrid electric vehicles (HEVs) powered by gasoline engines, the emission purification performance by TWC unfortunately become worse caused by mode switching from engine to battery and vice versa, which is possible to generate cold start conditions over and over for TWC In this study, targeting at reducing the emissions from series HEVs by early activation of TWC, numerical simulations with experiments are carried out. A HEV is tested on a chassis dynamometer under Worldwide Light-duty Test Cycle (WLTC) mode; the upstream and downstream gas conditions of the close-coupled catalyst converter are measured.
Technical Paper

A Fundamental Study on Combustion Characteristics in a Pre-Chamber Type Lean Burn Natural Gas Engine

2019-09-09
2019-24-0123
Pre-chamber spark ignition technology can stabilize combustion and improve thermal efficiency of lean burn natural gas engines. During compression stroke, a homogeneous lean mixture is introduced into pre-chamber, which separates spark plug electrodes from turbulent flow field. After the pre-chamber mixture is ignited, the burnt jet gas is discharged through multi-hole nozzles which promotes combustion of the lean mixture in the main chamber due to turbulence caused by high speed jet and multi-points ignition. However, details mechanism in the process has not been elucidated. To design the pre-chamber geometry and to achieve stable combustion under the lean condition for such engines, it is important to understand the fundamental aspects of the combustion process. In this study, a high-speed video camera with a 306 nm band-pass filer and an image intensifier is used to visualize OH* self-luminosity in rapid compression-expansion machine experiment.
Technical Paper

Analysis of TWC Operation Characteristics in a Euro6 Gasoline Light Duty Vehicle

2019-09-09
2019-24-0162
A Euro6 gasoline light duty vehicle has been tested at the engine dynamometer and the emissions have been analyzed upstream and downstream the Three-Way-Catalyst (TWC) during the WLTP cycle. Catalyst simulations have been used for assessing the processes inside the catalytic converter using a reaction scheme based on 19 brutto reactions (Direct oxidation and reduction, selective catalytic re-ductions with CO, C3H6 and H2, steam reforming, water-gas shift and bulk Ceria as well as surface Ce-ria reactions). The reactions have been parametrized in order to best approximate the measurements. Based on the reactions taken into account, the real vehicle emissions can be predicted with good accu-racy. The simulations show that the cycle emissions are comprising mainly by the cold start contribution as well as discrete emission break-through events during transients.
Technical Paper

Sub-23 nm Particulate Emissions from a Highly Boosted GDI Engine

2019-09-09
2019-24-0153
The European Particle Measurement Program (PMP) defines the current standard for measurement of particle number (PN) emissions from vehicles in Europe. This specifies a 50% count efficiency (D50) at 23 nm and a 90% count efficiency (D90) at 41 nm. Particulate emissions from Gasoline Direct Injection (GDI) engines have been widely studied, but usually only in the context of PMP or similar sampling procedures. There is increasing interest in the smallest particles – i.e. smaller than 23 nm – which can be emitted from vehicles. The literature suggest that by moving D50 to 10 nm, PN emissions from GDI engines might increase by between 35 and 50 % but there remains a lot of uncertainty.
Technical Paper

Experimental Investigations on Engine-Out Emissions Sensitivity to Fuel Injection Pressure of a High-Performance DISI Single Cylinder Engine

2019-09-09
2019-24-0169
In recent times complying with increasingly stringent emission regulations has become ever more challenging. While an efficient after-treatment system that includes gasoline particulate filter enables compliance with legislation requirements, lowering engine-out emissions by improving combustion system has to be considered as a crucial advantage not only in regard to pollutants emission control, but also performance. In this respect, high-performance enabling contents such as relatively large displacement, flow-capacity oriented intake ports and a limited stroke-to-bore ratio have significant drawbacks on the charge motion quality and as direct consequence on mixture formation and homogeneity.
Technical Paper

Hybrid Powertrain Calibration Techniques

2019-09-09
2019-24-0196
Meeting the particle (PN) emissions limits in dynamic vehicle test sequences needs specific attention on each power variation event occurring in the internal combustion engine (ICE). Such transients arise from engine start onwards along the entire test drive. In hybrid systems, there is one further source for transient ICE response: each power shift between E-motor (EM) and ICE introduces gas flow variations with subsequent temperature response in the ICE and in the engine aftertreatment system (EAS). This bears consequences for engine out emissions as well as for the EAS efficiency and even for the durability of a catalytic converter. As system calibration engineers must decide on numerous actuator parameters, their decisions, finally, are crucial for meeting legislative limits under the boundary conditions given by the ICE’s hybrid and drive environment.
X