Search Results

Spark-assisted compression ignition (SACI) leverages flame propagation to trigger autoignition in a controlled manner. The autoignition event is highly sensitive to several parameters, and thus, achieving SACI in production demands a high tolerance to variations in conditions. Limited research is available to quantify the combustion response of SACI to these variations. A simulation study is performed to establish trends, limits, and control implications for SACI combustion over a wide range of conditions. The operating space was evaluated with a detailed chemical kinetics model. Key findings were synthesized from these results and applied to a 1-D engine model. This model identified performance characteristics and potential actuator positions for a production-viable SACI engine. This study shows charge preparation is critical and can extend the low-load limit by strengthening flame propagation and the high-load limit by reducing ringing intensity.

Adiabatic heating during plastic straining can slow the diffusionless shear transformation of austenite to martensite in steels that exhibit transformation induced plasticity (TRIP). However, the extent to which the transformation is affected over a strain rate range of relevance to automotive stamping and vehicle impact events is unclear for most third-generation advanced high strength TRIP steels. In this study, an 1180MPa minimum tensile strength TRIP steel with carbide-free bainite is evaluated by measuring the variation of retained austenite volume fraction (RAVF) in fractured tensile specimens with position and strain. This requires a combination of servo-hydraulic load frame instrumented with high speed stereo digital image correlation for measurement of strains and ex-situ synchrotron x-ray diffraction for determination of RAVF in fractured tensile specimens.

This article presents a pointing gesture-based point of interest computation method via pointing rays’ intersections for situated awareness interactions in vehicles. The proposed approach is compared with two alternative methods: (a) a point of interest identification method based on the intersection of the pointing ray with the point cloud (PoC) resulting from the vehicle sensors, and (b) the traditional ray-casting approach, where the point of interest is computed based on the first intersection of the pointing rays with locations stored in a 2D annotated map. Simulation results show that the presented method outperforms by 36.25% the traditional ray casting one. However, as it was expected, the sensor-based computation method is more accurate. The validation of our approach was conducted by experiments performed in a test track facility.

This paper presents development of a multi-scale material model for a 980 MPa grade transformation induced plasticity (TRIP) steel, subject to a two-step quenching and partitioning heat treatment (QP980), based on integrated computational materials engineering principles (ICME Model). The model combines micro-scale material properties defined by the crystal plasticity theory with the macro-scale mechanical properties, such as flow curves under different loading paths. For an initial microstructure the flow curves of each of the constituent phases (ferrite, austenite, martensite) are computed based on the crystal plasticity theory and the crystal orientation distribution function. Phase properties are then used as an input to a state variable model that computes macro-scale flow curves while accounting for hardening caused by austenite transformation into martensite under different straining paths.

Low pressure (LP) and cooled EGR systems are capable of increasing fuel efficiency of turbocharged gasoline engines, however they introduce control challenges. Accurate exhaust pressure modeling is of particular importance for real-time feedforward control of these EGR systems since they operate under low pressure differentials. To provide a solution that does not depend on physical sensors in the exhaust and also does not require extensive calibration, a coupled temperature and pressure physics-based model is proposed. The exhaust pipe is split into two different lumped sections based on flow conditions in order to calculate turbine-outlet pressure, which is the driving force for LP-EGR. The temperature model uses the turbine-outlet temperature as an input, which is known through existing engine control models, to determine heat transfer losses through the exhaust.

The strain-induced diffusionless shear transformation of retained austenite to martensite during straining of transformation induced plasticity (TRIP) assisted steels increases strain hardening and delays necking and fracture leading to exceptional ductility and strength, which are attractive for automotive applications. A novel technique that provides the retained austenite volume fraction variation with strain with improved precision is presented. Digital images of the gauge section of tensile specimens were first recorded up to selected plastic strains with a stereo digital image correlation (DIC) system. The austenite volume fraction was measured by synchrotron X-ray diffraction from small squares cut from the gage section. Strain fields in the squares were then computed by localizing the strain measurement to the corresponding region of a given square during DIC post-processing of the images recorded during tensile testing.

The current work addresses efforts to characterize multiple-evaporator capillary pumped loops. Both experimental and analytical approaches were used to predict performance of parallel evaporators and corresponding effects from adjacent operating evaporators. The effects of low and high power dissipation and the distribution of powers among the evaporators were tested. Additionally, a pressure balance model is given where the maximum heat transfer capacity for an evaporator operating under a multi-evaporator condition is determined based on pressure distribution throughout the loop. The model and experiment comparisons demonstrated how the heat load distribution among evaporators affects the maximum capillary limit for individual evaporators operating in a multiple evaporator mode.

The first concept and early experiments of a mechanical counter pressure (MCP) spacesuit were published by Webb in the late 1960's. MCP provides an alternative approach to the conventional full pressure suit that bears some significant advantages, such as increased mobility, dexterity, and tactility. The presented ongoing research provides a thorough investigation of the physiological effect of mechanical counter pressure applied onto the human skin. In this study, we investigated local microcirculatory effects produced with negative and positive ambient pressure on the lower body as a preliminary study for a lower body garment. The data indicates that the positive pressure was less tolerable than negative pressure. Lower body negative and positive pressure cause various responses in skin blood flow due to not only blood shifts but also direct exposure to pressure differentials.

One of the intrinsic characteristics found in CPL operation is the oscillatory behavior of the pressure drop, even noted under seemingly steady operation. This study focused on the role of the condensing process and its intrinsic instabilities upon the differential pressure oscillations recorded in the CPL. Through an analytical study of condensing instabilities and an experimental study based on the correlation between pressure records and condensing flow visualization, the impact of slug flow phenomenon occurring in the condensing path was investigated. High amplitude oscillations were seen to be linked with liquid slug phenomena in the way that slug striking the final vapor-liquid interface generated pressure pulses.