Search Results

Improvements in component/system design is a daily challenge these days, always looking for high performance, reduced mass and low costs. The source for the best fit between these factors, coupled with adequate durability performance, is crucial to the success of a given product and this is what motivates engineering teams around the world. The demand for efficient projects with short deadlines for validation and certification is huge and simulation tools focused on accelerated durability and virtual validation are increasingly being used. When developing a new spring for commercial vehicles, lessons learned from the actual loads applied to the suspension are the “key” to a successful project. The loads/stresses from the ground (vertical loads, lateral loads, longitudinal and braking loads) are quite high and, consequently, relevant to the proper definition of the design of the suspension components.

A series of bending fatigue tests were conducted and S-N data were obtained for two groups of 4320 steel samples: (1) carburized, quenched and tempered, (2) carburized, quenched, tempered and shot peened. Shot peening improved the fatigue life and endurance limit. The S-N data exhibited large scatter, especially for carburized samples and at the high cycle life regime. Sample characterization work was performed and scatter bands were established for residual stress distributions, in addition to fracture and fatigue properties for 4320 steel. Moreover, a fatigue life analysis was performed using fracture mechanics and strain life fatigue theories. Scatter in S-N curves was established computationally by using the lower bound and upper bound in materials properties, residual stress and IGO depth in the input data. The results for fatigue life analysis, using either computational fracture mechanics or strain life theory, agreed reasonably well with the test data.

Prediction of fatigue performance of large structures and components is generally done through the use of a fatigue analysis software, FEA stress/strain analysis, load spectra, and materials properties generated from laboratory tests with small specimens. Prior experience and test data has shown that a specimen size effect exists, i.e. the fatigue strength or endurance limit of large members is lower than that of small specimens made of same material. Obviously, the size effect is an important issue in fatigue design of large components. However a precise experimental study of the size effect is very difficult for several reasons. It is difficult to prepare geometrically similar specimens with increased volume which have the same microstructures and residual stress distributions throughout the entire material volume to be tested. Fatigue testing of large samples can also be a problem due to the limitation of load capacity of the test systems available.

A nano-composite high strength (NCHS) steel was tested and evaluated in this work. Monotonic tension, strain controlled fatigue and fracture toughness tests were conducted at ambient temperature. Chemical composition, microstructure and fractography analysis were also performed. The NCHS steel showed excellent combination of high strength, high ductility and high fracture toughness with relatively low alloy content, compared with a S7 tool steel. Fatigue performance of the NCHS steel was also better than that of S7 tool steel. With the exceptional combination of high strength and high fracture toughness, the nano-composite high strength steel may have potential applications in gears, shafts, tools and dies where high fatigue performance, shock load resistance, wear and corrosion resistance is required.

As a part of a major research program with the aim of improving heavy truck drive axle fuel efficiency, this work focuses on seal friction torque test development and establishing pinion seal and wheel seal friction torque baseline data. Pinion seal and wheel seal friction torque was measured. The effect of speed and temperature on pinion seal friction torque was assessed. The effect of several coatings on pinion seal friction torque was evaluated. Pinion seal friction torque was also calculated and calculation result was compared with test data. Finally the impact of seal friction and bearing friction on total drive axle power loss was discussed.

Microwave plasmas at atmospheric pressures can be utilized for carburization of steel alloys. Due to their high frequencies, microwaves ionize and dissociate molecules with great efficiency and provide carbon for carburization by dissociating hydrocarbons that are introduced in the plasma. Also, conventional carburization techniques are not very energy efficient, as much of the heat generated is not utilized for the heating of the parts. Microwave plasmas are highly energy efficient due to very high coupling of microwaves to the plasma and then transferring of heat to the parts. Since plasma surrounds the part uniformly, heating rates over the part surface are also uniform. Preliminary results are presented for carburization of steel alloy 8620H by atmospheric microwave plasma process using acetylene as the source gas. Possible effects of application of pulsed DC bias to the parts are also discussed.

Current trends in vehicle development, including both automotive and commercial vehicles, are characterized by short model life cycles, reduced development time, concurrent design and manufacturing development, reduced design changes, and reduced total cost. All of these are driven by customer demand of higher load capacity, reduced weight, extended durability and warranty requirement, better NVH performance and reduced cost. These trends have resulted in increased usage of computational simulation tools in design, manufacturing, and testing, i.e. virtual testing or virtual prototyping. This paper summarizes our work in virtual testing, i.e. fatigue life simulations using computational fracture mechanics for commercial vehicle axle gearing development. First, fatigue life simulation results by using computational fracture mechanics CRACKS software were verified by comparing with gear teeth bending fatigue test data and three point bending fatigue test data.

Traditional methods often lead to truck component designs that are overly conservative. The ever-increasing need to reduce operational costs demands innovative means for producing parts that are light, durable and capable of carrying more loads. This paper discusses the far-reaching advantages of shape-optimization, beyond the fundamental stipulation of weight reduction. A suspension link is considered to demonstrate the benefits of an optimally shaped component.

The effect of multiple braze furnace exposures has been questioned by many because the rework of brazed parts is a common practice in manufacturing. However, there are process controls that limit the number of exposures for an assembly due to known issues with multiple exposures. A common concern deals with the effect of multiple braze furnace exposures on the structural integrity of the base material of the components. Another concern regards the effect of multiple exposures on the structural integrity of the braze joint itself. This paper details experimental results of a physical study to investigate these questions. The material forms used are seam-welded tube and a thin-wall stamped component, both made from 304L stainless steel. The copper paste used in the study has an industry designation of ANSI/AWS A5.8 - BCu-1a.

In this study an effort has been made to establish a response surface model to predict material thinning in a stamped chassis cross member. Numerical simulations using finite element method were performed to populate the data needed for response surface analysis. The results predicted by the response surface model were compared with the results of numerical simulations and were found to be in good agreement. The effect of corner radius, flange radius and flange height on material thinning was investigated using the response surface model.

The objective of this work is to test and develop monotonic tensile properties and strain controlled fatigue properties of a cast ductile iron. The test data and the related material constants will be used in conjunction with vehicle loading data to perform finite element stress-strain analysis and fatigue life prediction analysis to aid in the design of automotive components made from ductile iron. Currently, such material property data does not exist in the literature for this particular grade of ductile iron. Monotonic tension and fully reversed strain controlled fatigue tests were conducted by following ASTM E-8, ASTM E-606, and SAE J-1099 on samples machined from the cast ductile iron. Monotonic tensile properties were obtained, including Young's modulus, yield strength, ultimate tensile strength, elongation, reduction in area, strength coefficient K, and strain hardening exponent n.

Axle primary gearing is normally carburized for high and balanced resistance to contact fatigue, wear, bending fatigue, and impact loading. The focus of this work is on bending fatigue which is a key design consideration of automotive and commercial vehicle axle gearing. Since a carburized component is basically a composite material with steep gradients in carbon content, hardness, tensile strength and microstructure from surface to the middle of the cross section combined with non-linear residual stress, its bending fatigue life prediction is a complex and challenging task. Many factors affect the bending fatigue performance of axle gearing, such as gear design, gear manufacturing, loading history during service, residual stress distribution, steel grade, and heat treatment. In this paper, the general methodology for bending fatigue life prediction of a carburized component is investigated. Carburized steel composites are treated as two homogeneous materials: case and core.

Deionized (DI) water is being used for humidification and cooling on some fuel cell designs. This highly purified water is corrosive, yet the high purity is required to maintain the function and durability of the fuel cell. A study of the deionized water system was undertaken to determine the effect of various materials on water quality, and also to determine the effect of deionized water on each material. The test setup was designed to circulate fluid from a reservoir, similar to an actual application. The fluid temperature, pressure, and flow rate were controlled. The resistivity of the water was observed and recorded. Pre- and post-testing of the water and the materials was performed. The goal is to achieve system cleanliness and durability similar to a stainless steel system using lighter, less expensive materials. This paper describes the test setup, test procedures, and the overall results for the eight materials tested.

Higher demands from automotive customers for quieter vehicles and the reduction of noise and vibration levels from major sources like the engine necessitate better performance of other sources of noise and vibrations in a vehicle. One of these sources that Original Equipment Manufacturers (OEM) demand making quieter is the power steering system. The pressure ripple generated by the power steering pump transfers to the fluid lines where it can generate objectionable noise and vibrations. This can become an excitation force to the structure of a vehicle or the steering gear and can become a source of discomfort to the vehicle occupants. Attenuation of the pressure ripple within the hose assembly can result in significant reduction in noise inside the vehicle. The NVH research team at the Fluid System Products of Dana Corporation has developed “Dana's Virtual Test Rig (DVTR™),” - a hydraulic system simulation software.

A new wheel end concept was designed and developed to allow sport utility vehicles (SUV) and light trucks the possibility of achieving a negative scrub radius. This paper will compare a production vehicle with a scrub radius of 54.8 mm with the same vehicle modified with several alternate scrub radii. The vehicle changes are completed in a way that still packages the brake components and meets the component durability needs of a light truck wheel end load cycle. Quantitative vehicle computer analysis and actual instrumented vehicle performance data will be compared and correlated to analyze the effects of scrub radius.

A transfer case was designed to utilize electronic control. It has a planetary interaxle differential for proportional torque split. An electromagnetic clutch is applied across the differential to enhance mobility when road coefficients allow single wheel or single axle traction loss. The need for clutch actuation is monitored by an electronic module and sensor system, that detects abnormal amounts of differentiation in the interaxle unit. Clutch actuation is signaled and controlled by the module, which is also electrically connected to the rear axle ABS brake system to eliminate any possible simultaneous function compatibility issues. System emphasis is on foul weather mobility when negotiating highway and secondary roads. The family vehicle market was targeted and performance parameters were adjusted toward mobility and driver confidence to complete a given trip.