Search Results

In this paper, the results of finite element analyses for nodular cast irons with different volume fractions of graphite particles based on an axisymmetric unit cell model under uniaxial compression and tension are presented. The experimental compressive stress-strain data for a nodular cast iron with the volume fraction of graphite particles of 4.5% are available for use as the baseline material data. The elastic-plastic stress-strain relation for the matrix of the cast iron is estimated based on the experimental compressive stress-strain curve of the cast iron with the rule of mixture. The elastic-plastic stress-strain relation for graphite particles is obtained from the literature. The compressive stress-strain curve for the cast iron based on the axisymmetric unit cell model with the use of the von Mises yield function was then obtained computationally and compared well with the compressive stress-strain relation obtained from the experiment.

In this paper, the evolution equation for the active yield surface during the unloading/reloading process based on the pressure-sensitive Drucker-Prager yield function and a recently developed anisotropic hardening rule with a non-associated flow rule is first presented. A user material subroutine based on the anisotropic hardening rule and the constitutive relation was written and implemented into the commercial finite element program ABAQUS. A two-dimensional plane strain finite element analysis of a crankshaft section under fillet rolling was conducted. After the release of the roller, the magnitude of the compressive residual hoop stress for the material with consideration of pressure sensitivity typically for cast irons is smaller than that without consideration of pressure sensitivity. In addition, the magnitude of the compressive residual hoop stress for the pressure-sensitive material with the non-associated flow rule is smaller than that with the associated flow rule.

A number of spark ignition engines from 1997 to 2003 are analyzed for their overall friction characteristics using the Willans line approach. This methodology appears to be quite robust across many different types of engines. Using a variety of partial and complete engine maps from multiple manufacturers, it is confirmed that engine friction has been decreasing over the decades (compared to past studies). Overall there has been a 25% reduction over 30 years. It is also demonstrated that thermal efficiency (defined here as the slope of fuel mep and bmep excluding enrichment) has been remaining steady during the same period. The application to aggregate engine models is discussed.

In an effort to improve fuel economy for light duty trucks, an initiative was undertaken to reduce frictional losses in rear axle through use of low friction lubricants and novel surface finish on gears while maintaining durability. This paper describes the effect of rear axle lubricants on fuel economy. A laboratory rig was set up using a full size pick-up truck rear axle to measure axle efficiency and lubricant temperature with various SAE 75W-90 and SAE 75W-140 viscosity grade lubricants. Traction coefficients of lubricants were also measured at various temperatures using a laboratory ball and disk contact geometry. An improvement in axle efficiency up to 4.3% was observed over current Ford factory fill SAE 75W-140 lubricant depending on speed, torque and the type of lubricant used. The temperature of the lubricants was also lower than that with the current factory fill. This is important for maintaining bearing life and overall durability of the rear axle.

The newly developed Sequence VIB engine dynamometer test for measuring the ability of engine oils to improve engine fuel efficiency was designed as an improvement on its predecessor, the Sequence VIA test. The Sequence VIB test features an additional, extended oil aging to correspond to aging of engine oils in certification vehicles and in customer use, and a new set of boundary/mixed and hydrodynamic lubrication stages to better represent a wider range of engines. Five fuel economy measurement stages were chosen for the Sequence VIB test from a larger set of prototype stages, based on extensive friction modeling of engines, analysis of Sequence VIA data on reference oils, and operational considerations. Time factors for these stages were derived based on a mini-mapping of engines considering engine operating conditions in the Metro/Highway Federal fuel economy test procedure (FTP M/H) and the estimated market volume of each engine-vehicle.

Lubrication conditions in journal bearings lubricated with low friction engine oils have been investigated using two complementary experimental techniques. Load supporting capacity under conditions ranging from fully flooded to mixed lubrication was measured for several candidate oils using a bench test that simulates the dynamic motion of a journal bearing at fixed, measurable eccentricities. The performance of these oils was also assessed using a bearing test rig in which journal friction is measured under typical engine conditions of speed, load and temperature. Significant mixed lubrication conditions were shown to exist at low speeds in heavily loaded journal bearings. Under such conditions, oil with friction reducing additives exhibit higher load supporting capacity, distinct separation of moving parts, and reduced friction relative to oils without such additives.