Search Results

With the advent of this new era of electric-driven automobiles, the simulation and virtual digital twin modeling world is now embarking on new sets of challenges. Getting key insights into electric motor behavior has a significant impact on the net output and range of electric vehicles. In this paper, a complete 3D CFD model of an Electric Motor is developed to understand its churning losses at different operating speeds. The simulation study details how the flow field develops inside this electric motor at different operating speeds and oil temperatures. The contributions of the crown and weld endrings, crown and weld end-windings, and airgap to the net churning loss are also analyzed. The oil distribution patterns on the end-windings show the effect of the centrifugal effect in scrapping oil from the inner structures at higher speeds. Also, the effect of the sump height with higher operating speeds are also analyzed.

Range anxiety in current battery electric vehicles is a challenging problem, especially for commercial vehicles with heavy payloads. Therefore, the development of electrified propulsion systems with multiple power sources, such as fuel cells, is an active area of research. Optimal speed planning and energy management, referred to as eco-driving, can substantially reduce the energy consumption of commercial vehicles, regardless of the powertrain architecture. Eco-driving controllers can leverage look-ahead route information such as road grade, speed limits, and signalized intersections to perform velocity profile smoothing, resulting in reduced energy consumption. This study presents a comprehensive analysis of the performance of an eco-driving controller for fuel cell electric trucks in a real-world scenario, considering a route from a distribution center to the associated supermarket.

Zinc-based electrogalvanized (EG) and hot-dip galvanized (HDGI) coatings have been widely used in automotive body-in-white components for corrosion protection. The formability of zinc coated sheet steels depends on the properties of the sheet and the interactions at the interface between the sheet and the tooling. The frictional behavior of zinc coated sheet steels is influenced by the interfacial conditions present during the forming operation. Friction behavior has also been found to deviate from test method to test method. In this study, various lubrication conditions were applied to both bending under tension (BUT) test and a draw bead simulator (DBS) test for friction evaluations. Two different zinc coated steels; electrogalvanized (EG) and hot-dip galvanized (HDGI) were included in the study. In addition to the coated steels, a non-coated cold roll steel was also included for comparison purpose.

As passenger vehicle design evolves and accelerates, the use of multi-body dynamics solvers has proven to be invaluable in the engineering workflow. MBD solvers allow engineers to build virtual vehicle models that can accurately simulate vehicle responses and calculate internal forces, which previously could only be assessed using physical prototype builds with hundreds of measurement transducers. Evaluation and selection of solvers within an engineering environment is inherently a multi-dimensional activity that can include ease of use, retention of previously developed expertise, accuracy, speed, and integration with existing analysis processes. We discuss here some of the challenges present in developing capability and accumulating data to support each of these criteria. Developing a pilot model that is capable of being applied to a comprehensive set of use cases, and then verifying those use cases, required significant project management activity.

Analyzing low frequency brake noise (< 300Hz) has been challenging due to the difficulty associated with calculating dynamic friction behavior and its multiple structure-borne noise transfer paths. In theory, it is possible to simulate sound pressure level inside the cabin by calculating a transfer function between friction excitation, which is on the interface between rotor and pads, and cabin acoustic response, and by multiplying dynamic friction force at the rotor-pad interface to that transfer function. However, calculating the dynamic friction forces when brake noise occurs has been one of the most challenging research topics in the brake community. This paper describes a novel concept to simulate sound pressure level inside the cabin without knowing the dynamic friction forces at the rotor-pad interface in advance.

Euro 7/VII regulations are currently under discussion and are expected to be the last big regulatory step in Europe. From available documentation, it is clear the aim of further regulating the extended conditions of use which are still responsible of high emission events (e. g. cold start or altitude) as well as regulating secondary emissions such as NH3, N2O, CH4, Aldehydes (HCHO). Even if not completely fixed yet, the EU7 limits will be challenging for internal combustion engines and even more for Diesel. Despite a consistent reduction of market share, Diesel engines are expected to remain a significant portion in certain sectors such as Heavy duty (HD) and Light-commercial vehicle (LCV) for some decades. In order to reach the new limits being proposed, besides minimizing engine-out emissions, Diesel powertrain will need an aftertreatment system able to work at very high efficiency right after engine start and in almost every working and environmental condition.

A computational study based on unsteady Reynolds-Averaged-Navier-Stokes that resolves the gas-liquid interface was performed to examine the unsteady multiphase flow in a 4 cylinder Inline (i-4) engine. In this study, the rotating motion of the crankshaft and reciprocating motion of the pistons were accounted for to accurately predict the oil distribution in various parts of the engine. Three rotational speeds of the crankshaft have been examined: 1000, 2800, and 4000 rpm. Of particular interest is to examine the mechanisms governing the process of oil drawdown from the engine head into the case. The oil distributions in other parts of the engine have also been investigated to understand the overall crankcase breathing process. Results obtained show the drawdown of oil from the head into the case to be strongly dependent on the venting strategy for the foul air going out of the engine through the PCV system.

The continuous improvement of internal combustion engines (ICEs) with strategies that can be applied to existing vehicle platforms, either directly or with minor modifications, can improve efficiency and reduce GHG emissions to help achieve Paris climate targets. Low carbon fuels (LCF) as diesel substitutes for light and heavy-duty vehicles are currently being considered as a promising alternative to reduce well-to-wheel (WTW) CO2 emissions by taking advantage of the carbon offset their synthesis pathway can promote, which could capture more CO2 than it releases into the atmosphere. Additionally, some low carbon fuels, like OMEx blends, have non-sooting properties that can significantly improve the NOx-soot tradeoff. The current work studies the calibration optimization of a EU6D-TEMP light-duty engine using various LCFs with different renewable contents with the goal of reduced NOx emissions.

The H-point is a critical part of vehicle design as it is the basis for many engineering dimensions within the vehicle interior. A complete design process includes comparisons of the design to competitive benchmark vehicles. However, the competitive design considerations needed to determine the common standard H-point reference are often unknown. The SAE Human Accommodation and Design Devices (HADD) technical committee recently published a new standard benchmark SgRP procedure [2]. This new standard practice needed to be tested with respect to the accuracy and repeatability for determining the unknown h-point design parameters within industry benchmarking tolerances. In 2019, the SAE HADD committee conducted a study to evaluate the reproducibility of the new procedure. This paper presents detailed results of that study and discusses opportunities for applying the new benchmark practice.

The engine operating point (EOP), which is determined by the engine speed and torque, is an important part of a vehicle's powertrain performance and it impacts FC, available propulsion power, and emissions. Predicting instantaneous EOP in real-time subject to dynamic driver behaviour and environmental conditions is a challenging problem, and in existing literature, engine performance is predicted based on internal powertrain parameters. However, a driver cannot directly influence these internal parameters in real-time and can only accommodate changes in driving behaviour and cabin temperature. It would be beneficial to develop a direct relationship between the vehicle-level parameters that a driver could influence in real-time, and the instantaneous EOP. Such a relationship can be exploited to dynamically optimize engine performance.

Third generation advanced high strength steels (AHSS) that rely on the transformation of austenite to martensite have gained growing interest for implementation into vehicle architectures. Previous studies have identified a dependency of the rate of austenite decomposition on the amount of strain and the associated strain path imposed on the sheet. The rate and amount of austenite transformation can impact the work hardening behavior and tensile properties. However, a deeper understanding of the impact on toughness, and thus crash performance, is not fully developed. In this study, the strain path and strain amounts were systematically controlled to understand the associated correlation to impact toughness in the end application condition (strained and baked). Impact toughness was evaluated using an instrumented Charpy machine with a single sheet v-notch sample configuration.

The REAL NOx regulation requires tracking and reporting of NOx emissions starting in 2022MY for both medium-duty and heavy-duty diesel vehicles with potential to be considered during the next light-duty rulemaking. The regulation includes minimum NOx mass measurement accuracy requirements of either +/−20 percent or +/− 0.1 g/bhp-hr. Existing NOx sensor technology may not be able to meet the regulated accuracy requirements especially when exposed to other sources of variation within the emissions control system. This paper provides an assessment of real-world NOx sensor accuracy and the impact of other sources of variation and noise factors on NOx measurement accuracy. Noise factors investigated include NOx sensor tolerance, exhaust flow rate estimation, NOx sensor ammonia (NH3) cross sensitivity, mass air flow (MAF) sensor accuracy, NOx sensor placement, and laboratory emissions measurement capability.

The past five years have seen significant research into autonomous vehicles that employ a by-wire steering rack actuator and no steering wheel. There is a clear synergy between these advancements and the parallel development of complete Steer-by-Wire systems for human-operated passenger vehicle applications. Steer-by-Wire architectures presented thus far in the literature require multiple layers of electrical and/or mechanical redundancy to achieve the safety goals. Unfortunately, this level of redundancy makes it difficult to simultaneously achieve three key manufacturer imperatives: safety, reliability, and cost. Hindered by these challenges, as of 2020 only one production car platform employs a Steer-by-Wire system. This paper presents a Steer-by-Wire architectural solution featuring fail-operational steering control architected with the objective of achieving all system safety, reliability, and cost goals.

This study evaluated the interactions between sheet steel, lubricant and measurement system under typical sheet forming conditions using a fixed draw bead simulator (DBS). Deep drawing quality mild steel substrates with bare (CR), electrogalvanized (EG) and hot dip galvanized (HDG) coatings were tested using a fixed DBS. Various lubricant conditions were targeted to evaluate the coefficient of friction (COF) of the substrate and lubricant combinations, with only rust preventative mill oil (dry-0 g/m2 and 1 g/m2), only forming pre-lube (dry-0 g/m2, 1 g/m2, and >6 g/m2), and a combination of two, where mixed lubrication cases, with incremental amounts of a pre-lube applied (0.5, 1.0, 1.5 and 2.0 g/m2) over an existing base of 1 g/m2 mill oil, were analyzed. The results showed some similarities as well as distinctive differences in the friction behavior between the bare material and the coatings.

A Machine Learning (ML) approach is presented to correlate in-cylinder images of early flame kernel development within a spark-ignited (SI) gasoline engine to early-, mid-, and late-stage flame propagation. The objective of this study was to train machine learning models to analyze the relevance of flame surface features on subsequent burn rates. Ultimately, an approach of this nature can be generalized to flame images from a variety of sources. The prediction of combustion phasing was formulated as a regression problem to train predictive models to supplement observations of early flame kernel growth. High-speed images were captured from an optically accessible SI engine for 357 cycles under pre-mixed operation. A subset of these images was used to train three models: a linear regression model, a deep Convolutional Neural Network (CNN) based on the InceptionV3 architecture and a CNN built with assisted learning on the VGG19 architecture.

More than four decades ago, the concept of zero defects was coined by Phillip Crosby. It was only a vision at the time, but the introduction of Artificial Intelligence (AI) in manufacturing has since enabled it to become attainable. Since most mature manufacturing organizations have merged traditional quality philosophies and techniques, their processes generate only a few Defects Per Million of Opportunities (DPMO). Detecting these rare quality events is one of the modern intellectual challenges posed to this industry. Process Monitoring for Quality (PMQ) is an AI and big data-driven quality philosophy aimed at defect detection and empirical knowledge discovery. Detection is formulated as a binary classification problem, where the right Machine Learning (ML), optimization, and statistics techniques are applied to develop an effective predictive system.

Seat lateral support is often talked about as a design parameter, but usually in terms of psychological perception. There are many difficulties in quantifying lateral support mechanically to the engineering teams: Anthropometric variation causes different people to interact with the seat in different places and at different angles, BPD studies are usually planar and don’t distinguish between horizontal support and vertical resistance to sinking in, most mechanical test systems are typically single-DOF and can’t apply vertical and horizontal loads concurrently, and there is scant literature describing the actual lateral loads of occupants. In this study, we characterize the actual lateral loading on example seating from various sized/shaped occupants according to dynamic pressure distribution. From this information, a six-DOF load and position control test robot (KUKA OccuBot) is used to replicate that pressure distribution.

Given continued industry focus on reducing parasitic losses, the ability to accurately measure the magnitude of losses on all driveline components is required. A standardized test procedure enables manufacturers and suppliers to measure component losses consistently, in addition to offering a reliable process to assess enablers for efficiency improvements. This paper reviews the development of SAE draft standard J3218, which is a comprehensive test procedure to break-in and characterize the efficiency of beam axles. Focus areas of the study included ensuring the axle’s efficiency does not change as it is being characterized, building a detailed map of efficiency at a wide range of operating points, and minimizing test time. The resulting break-in procedure uses an asymptotic regression approach to predict fully broken in efficiency of the axle and determine how much the efficiency of the axle changes during the characterization phase.

Electric Vehicles are typically thought of as being quiet and refined, but they do come with some unique N&V challenges. Some of these challenges include a natural sound that can be undesirable due to its tonal nature, presence of high frequency, discontinuities in sound, and characteristics and levels that do not always naturally increase with motor torque and vehicle speed. One approach to address those challenges is Electric Vehicle Sound Enhancement (EVSE) which is a software feature embedded within the infotainment system. EVSE can be used to improve the perception of the vehicle by enhancing the preferred natural sounds of the vehicle, masking unusual and annoying components of the sound and aurally conveying information related to the vehicle performance. A jury study was conducted to better understand how EVSE can be used to accomplish this.

Electrical connections have a normal operational temperature range. A high resistance, such as a poor connection, in an electrical circuit has been reported to cause a temperature increase exceeding normal operational range at the connection. This study measures the temperature increase in a typical automotive bolted battery cable connection with low to zero torque values and simulated high resistance under different load conditions. The torque is changed from maximum design value to 0 Nm and the temperature increase at the connection is measured. The high resistance connections, manually created by adjusting the contacts, are tested for several power loss values at the connection. The temperature rise under these conditions at the connection is measured and subsequently recorded. The maximum temperature increase at the bolted cable connection recorded at low torque values including 0 Nm torque compared to the maximum typical design value of 17 Nm is 10.5 °C.