Search Results

In the context of CO₂ emission regulations and increase of energy prices, the downsizing of engine displacement is a widely discussed solution that allows a reduction of fuel consumption. However, high power density is required in order to maintain the power output and a good driveability. This study demonstrates the potential to strongly increase the specific power of High Speed Diesel Injection (HSDI) diesel engines. It includes the technological requirements to achieve high specific power and the optimal combination of engine settings to maximize specific power. The results are based on experimental work performed with a prototype single-cylinder engine (compression ratio of 14). Tests were conducted at full load, 4000 rpm. Part load requirements are also taken into account in the engine definition to be compatible with the targets of new emission standards.

In order to address the CO₂ emissions issue and to diversify the energy for transportation, CNG (Compressed Natural Gas) is considered as one of the most promising alternative fuels given its high octane number. However, gaseous injection decreases volumetric efficiency, impacting directly the maximal torque through a reduction of the cylinder fill-up. To overcome this drawback, both independent natural gas and gasoline indirect injection systems with dedicated engine control were fitted on a RENAULT 2.0L turbocharged SI (Spark Ignition) engine and were adapted for simultaneous operation. The main objective of this innovative combination of gas and liquid fuel injections is to increase the volumetric efficiency without losing the high knocking resistance of methane.

The air entrainment of multi-hole diesel injection is investigated by high speed Particle Image Velocimetry (PIV) using a multi-hole common rail injector with an injection pressure of 100 MPa. The sprays are observed in a high pressure, high temperature cell that reproduces the thermodynamic conditions which exist in the combustion chamber of a diesel engine during injection. Typical ambient temperature of 800K and ambient density of 25 kg/m3 are chosen. The air entrainment is studied with the PIV technique, giving access to the velocity fields in the surrounding air and/or in the interior of two neighboring jets. High acquisition rate of 5000 Hz, corresponding to 200 μs between two consecutive image pairs is obtained by a high-speed camera coupled with a high-speed Nd:YLF laser. The effect of neighboring jets interaction is studied by comparing four injectors with different numbers of holes (4, 6, 8 and 12) with similar static mass flow rate per hole.

Among the last years, environmental concerns have raised the interest for biofuels. Ethanol, blended with gasoline seems particularly suited for the operation of internal combustion engines, and has been in use for severals years in some countries. However, it has a strong impact on engine performance, which is emphasized on recent engine architectures, with downsizing through turbocharging and variable valve actuation. Taking all the benefits of ethanol-blended fuel thus requires an adaptation of the engine management system. This paper intends to assess the effect of gasoline-ethanol blending from this point of view, then to describe a mean-value model of a fuel-flexible turbocharged PFI-SI engine, which will serve as a basis for the development of control algorithms. The focus will be in this paper on ethanol content estimation in the blend, supported by both simulation and experimental results.

An unified model with a single set of kinetic parameters has been proposed for modeling laminar flame velocities of several alkanes using detailed kinetic mechanisms automatically generated by the EXGAS software. The validations were based on recent data of the literature. The studied compounds are methane, ethane, propane, n-butane, n-pentane, n-heptane, iso-octane, and two mixtures for natural gas and surrogate gasoline fuel. Investigated conditions are the following: unburned gases temperature was varied from 300 to 600 K, pressures from 0.5 to 25 bar, and equivalence ratios range from 0.4 to 2. For the overall studied compounds, the agreement between measured and predicted laminar burning velocities is quite good.

Recent developments on highly downsized spark ignition engines have been focused on knocking behaviour improvement and the most advanced technologies combination can face up to 2.5 MPa IMEP while maintaining acceptable fuel consumption. Unfortunately, knocking is not the only limit that strongly downsized engines have to confront. The improvement of low-end torque is limited by another abnormal combustion which appears as a random pre-ignition. This violent phenomenon which emits a sharp metallic noise is unacceptable even on modern supercharged gasoline engines because of the great pressure rise that it causes in the cylinder (up to 20 MPa). The phases of this abnormal combustion have been analysed and a global mechanism has been identified consisting of a local ignition before the spark, followed by a propagating phase and ended by a massive auto-ignition. This last step finally causes a steep pressure rise and pressure oscillations.

The combination of air charging and downsizing is known to be an efficient solution to reduce CO2 emissions of modern gasoline engines. The decrease of the cubic capacity and the increase of the specific performance help to reduce the fuel consumption by limiting pumping and friction losses and even the losses of energy by heat transfer. Investigations have been conducted on a highly downsized SI engine to confirm if a strong decrease of the displacement (50 %) was still interesting regarding the fuel consumption reduction and if other ways were possible to improve further more its efficiency. The first aim of our work was to identify the optimal design (bore, stroke, displacement, …) that could maximize the consumption reduction potential at part load but also improve the engine's behaviour at very high load (up to 3.0 MPa IMEP from 1000 rpm). In order to do that, four engine configurations with different strokes and bores have been tested and compared.

Facing the CO2 emission reduction challenge, the combination of downsizing and turbocharging appears as one of the most promising solution for the development of high efficiency gasoline engines. In this context, as knock resistance is a major issue, limiting the performances of turbocharged downsized gasoline engines, fuel properties are more than ever key parameters to achieve high performances and low fuel consumption's levels. This paper presents a combustion study carried out into the GSM consortium of fuel quality effects on the performances of a downsized turbocharged Direct Injection SI engine. The formulation of two adapted fuel matrix has allowed to separate and evaluate the impacts of three major fuel properties: Research Octane Number (RON), Motor Octane Number (MON) and Latent Heat of Vaporization (LHV). Engine tests were performed on a single cylinder engine at steady state operating condition.

The influence of the type of fuel and the feeding means to a DOC, in order to regenerate a DPF, was investigated. Diesel fuel in cylinder late post-injection was compared to the injection in the exhaust line, through an exhaust port injector, of diesel fuel, B10 (diesel fuel containing 10% of esters) and gasoline. Diesel fuel exhaust injection resulted in a deteriorated conversion efficiency, while the incorporation of esters to the diesel fuel was demonstrated to have no influence. Gasoline exhaust injection led to less HC slip than diesel fuels. Temperature dynamics resulting from injection steps showed taught that the shorter the hydrocarbons (within the tested fuels), the slower the response. These differences can be caught by simple models, leading to interesting opportunities for the model-based control of the DPF inlet temperature during active regenerations.

A tracer laser-induced fluorescence (LIF) technique for the visualisation of fuel distribution in the presence of oxygen was developed and then used sequentially with high speed chemiluminescence imaging to study the correlation between the mixing and auto-ignition processes of high pressure Diesel jets. A single hole common rail Diesel injector allowing high injection pressures up to 150MPa was used. The reacting fuel spray was observed in a high pressure, high temperature cell that reproduces the thermodynamic conditions which exist in the combustion chamber of a Diesel engine during injection. Both free jet and flat wall impinging jet configurations were studied. Several tracers were first considered with the objective of developing a tracer-LIF technique in the presence of oxygen. 5-nonanone was selected for its higher fluorescence efficiency.

Within the framework of the French research program PREDIT, a study was undertaken by ADEME, IFP, LGRE, PSA Peugeot Citroën and Umicore, whose main objective was a better understanding of the NOx storage and reduction phenomena on an aged, sulfated and desulfated NOx-trap. The target of this work was to use the information on catalyst working conditions to optimize catalyst management for a gasoline direct injection engine. The catalysts were characterized on both engine and synthetic gas benches. Aging and poisoning phenomena were studied and a variety of different chemical analytical tools were used. The behavior of two different thermally aged cores was investigated under rich conditions on a synthetic gas test bench. The dependence of the NOx regeneration efficiency of the traps is reported for several operating parameters, including reductant concentrations, durations of the rich pulse and trap loadings.

A lumping model has been formulated to calculate the thermodynamic properties required for internal combustion engine multidimensional computations, including saturation pressure, latent heat of vaporization, liquid density, surface tension, viscosity, etc. This model consists firstly in reducing the analytical data to a single (i.e. pure) pseudo-component characterized by its molecular weight, critical pressure and temperature, and acentric factor. For a gasoline fuel, the required analytical data are those provided by gas chromatography. For a Diesel fuel, the required data are a true boiling point (TBP) distillation curve and the fuel density at a single temperature. This model provides a valuable tool for studying the effects of fuel physical properties upon the behavior of a vaporizing spray in a chamber, as well as upon direct injection gasoline and Diesel engines using the multidimensional (3D) KMB code.

Penetration and combustion of fuel sprays is studied in conditions similar to gasoline direct injection engines. A closed pressurized and heated injection cell is used. It is equipped with quartz windows providing large optical accesses. A homogeneous flammable mixture is introduced in the cell and ignited to raise the internal pressure and temperature. Liquid fuel is injected at the time when the desired thermodynamic conditions are reached. Conditions representative of late injection in a direct-injection engine are selected. Gasoline spray ignition and combustion is provided by a spark plug with long electrodes, locating the electrode gap right in the middle of the spray. The combustion does not reach the wall, which makes this experiment interesting for the validation of combustion in CFD codes. Two pressure swirl injectors with spray angles of 60 and 90 degree are used. The fuel is iso-octane with 5% 3-pentanone as tracer.

A methodology has been developed to determine, for every cycle on which significant knock is detected, the area in which self-ignition occurs. This methodology is based on the exploitation by a dedicated algorithm of a minimum of 4 simultaneous combustion chamber pressure measurements. The algorithm has been first tested on the results of engine knocking simulation, then applied with success on a single-cylinder engine equipped with classical pressure transducers and with an instrumented cylinder head gasket developed for this application. The results obtained with these two kinds of transducers on several engine configurations and tunings are similar. If the timing and intensity of knock events depend on all engine parameters, its location is especially sensitive to such design parameters as fluid motion into the combustion chamber and spark plug position.

The use of Diesel engines has strongly increased during the last years and now represents 30% of the sales in Europe and up to 50% of the number of cars in circulation for some countries. This success is linked not only to the economical aspect of the use of such vehicles, but also to the recent technological improvements of these engines. The new technical solutions (high pressure direct injection, turbocharging…) have indeed allowed the increase of these engine performances while decreasing their fuel consumption, pollutant emissions and noise level. From an environmental point of view, Diesel engines are nevertheless penalized by their particulate and NOx emissions. The study and the treatment of the particulate, highly criticized for their potential impact on health, are the subject of numerous works of characterization and developments. PSA Peugeot-Citroën has recently launched its particulate filter technology on several types of vehicles.

KIFP, an hexahedral unstructured version of KIVA-MB (KMB), the current CFD code for engines at IFP, has been developed. Based on KIVA algorithms (finite volume on staggered grids, time-splitting, SIMPLE loop, sub-cycled advection…), the new solver has been built step by step with a strong control on the numerical results. This paper shows the different phases of this work. The numerical approaches and developments are discussed. Several moving grids algorithms have been tested without the flow and results are presented. The flow with its physical properties has been implemented step by step. Some academic examples are shown and compared with KMB or analytical results, like scalar advection or multi-species diffusion. Better precision and convergence in the physical fields are observed. Iterative loops and advective sub-cycles are also reduced thanks to the unstructured formalism. Super-scalar machines being widely used and developed, KIFP is dedicated for them.

Soot models applied to Diesel combustion can be grouped into two classes, one based on the flamelet concept and the other based on the homogeneous reactor concept. The first assumes that the laminar diffusion flame structure of the reaction zone, in the mixture fraction space, is preserved while convected and strained by the turbulent flow. The second assumes that the properties of the reaction zone are locally homogeneous. Thus the aerodynamic and chemical reaction interactions are modeled with opposing assumptions: the first assumes fast chemistry, the second fast mixing. In this work, we first compare results obtained with a flamelet library approach to those with a homogeneous reactor approach. Recognizing that both types of models apply in different regions of Diesel combustion, we then propose a new approach for soot modeling in which they are coupled.

The purpose of the ELEVATE (European Low Emission V4 Automotive Two-stroke Engine) industrial research project is to develop a small, compact, light weight, high torque and highly efficient clean gasoline 2-stroke engine of 120 kW which could industrially replace the relatively big existing automotive spark ignition or diesel 4-stroke engine used in the top of the mid size or in the large size vehicles, including the minivan vehicles used for multi people and family transportation. This new gasoline direct injection engine concept is based on the combined implementation on a 4-stroke bottom end of several 2-stroke engine innovative technologies such as the IAPAC compressed air assisted direct fuel injection, the CAI (Controlled Auto-Ignition) combustion process, the D2SC (Dual Delivery Screw SuperCharger) for both low pressure engine scavenging and higher pressure IAPAC air assisted DI and the ETV (Exhaust charge Trapping Valve).

The reduction of particulate emissions from Diesel engines is a key issue to meet future emission standards. Particulate traps represent an attractive solution to the problem of this source of pollution. However, they have the disadvantage of requiring periodic and safe regeneration to release exhaust back pressure and to recover filtration efficiency. Natural regeneration of the particulate filter may occur. Nevertheless, with light-duty vehicles and their low level of exhaust gas temperature, it may be necessary to facilitate or force the regeneration. The objective of this work is to give an overview of the possibilities offered by the engine management system to increase significantly exhaust gas temperatures. Thus, different engine tunes, through injection timing, boost pressure or EGR rate, may be sufficient to ensure safe regeneration of the trap.

A database of information concerning the spray development and pollutant formation in common-rail, direct-injection Diesel engine is constructed using a transparent model Diesel engine. Spray development is investigated using optical diagnostics: Mie scattering and Laser Induced Exciplex Fluorescence (LIEF) make possible qualitative visualization of liquid and vapor phases. The injection pressure/nozzle hole diameter is found to be the most important parameter (in the parameter range used for the study): it reduces the liquid penetration length and improves the mixing of vapor fuel. Direct imaging of combustion development shows the influence of different engine parameters on flame location. Comparison with measured vapor distributions shows the effect of thermal expansion on the vapor plume before any light from combustion is visible. Soot formation is investigated using Laser Induced Incandescence imaging.