Search Results

Recently, there has been a new method for setting bearing preload on tapered roller bearings in a power transmission system. To move this new method into production, an analytical model that relates the bearing preload to the stiffness of the bearing was developed. This work develops an analytical model that links the preload on multi-row tapered roller bearings to the stiffness of the power transmission system. This study also validates the proposed analytical model by comparing it to both previous work and commercially available simulation software. The analytical model has shown that it is highly sensitive to the number of rollers in the bearing, which is discussed in this work.

Online road profiling capability is required for automotive active suspension systems to be realized in a commercial landscape. The challenges that impede the realization of these systems include a profiler’s ability to maintain an optimal resolution of the oncoming road profile (spatial frequency). Shifting of the profile measurement frame of reference due to body motion disturbances experienced by the vehicle also negatively impacts profiling capability. This work details the early development of a corrective look-ahead road profiling system (CLARPS) and its control logic. The CLARPS components are introduced and additional focus will be given to the development of the angle generating function (AGF) and how it drives the ability of the system to optimize look-ahead viewing angles for the best spatial frequency resolution of a road profile. The CLARPS simulation environment is demonstrated with numerical comparison of simulated road profiles at varying vehicle speeds.

Designing a centrifugal pump impeller comes with challenges due to multiple parameters that affect the pump efficiency. A high velocity gradient exists in the flow between the impeller shroud and sidewall of the pump casing due to one surface stationary and the other moving at a high velocity. The internal rotating flow in the impeller shroud-sidewall gap is a major problem that leads to a decrease in pump performance. This study presents a design modification of the gap between the impeller shroud and the pump casing sidewall using an idler disk located in between, which rotates freely during pump operation. In this paper, a numerical analysis was performed to investigate the idler disk's effect on the pump performance for different volumetric flow rate values and idler disk geometries. ANSYS-2019-R1 was used (FLUENT solver) to carry out the computational fluid dynamics (CFD) analysis for evaluating the performance of the baseline and modified designs in a centrifugal pump.

The objective of this study is to develop a robust framework to model shock-turbulence interactions that happen in many engineering applications dealing with compressible flows. The model is essentially a hybrid algorithm to address the conflict between turbulence modeling and shock-capturing requirements. A skew-symmetric form of a co-located finite volume scheme with minimum aliasing errors is implemented to model the turbulent region in the combination of a semi-discrete, central scheme to capture the discontinuities with sufficiently low dissipation to minimize the effect of large eddy simulation (LES) for turbulent flows. To evaluate the effectiveness of the model, LESs are conducted to study the interaction of stationary shocks with turbulent flows. The simulations of the shock-turbulence interaction show the same physical trends as previously published results for high-fidelity DNS and LES.

Enhancing the performance of centrifugal pumps requires a thorough understanding of the internal flow. Flow simulation inside the pump can help understand the rotatory motion induced by the impellers, as well as the flow instabilities. The flow inside a centrifugal pump is three dimensional, disturbed and accompanied by tributary flow structures. When a centrifugal pump operates under low flow rates, a secondary flow known as recirculation starts to begin. The separation of flow occurs which creates vortices and decreases local pressure which induces cavitation. This phenomenon of recirculation will rise the Net Positive Suction Head Required (NPSHR). This work aims to improve the pump efficiency under low flow rates by adding multiple cylindrical disks at the pump inlet section to suppress the flow recirculation. In this study, a numerical simulation is carried out to investigate the influence on the pump internal flow by adding multi cylindrical disks.

A cooling fan is an essential device of the engine cooling system which is used to remove the heat generated inside the engine from the system. An essential element for successful fan designs is to evaluate the pressure over the fan blade since it can generate annoying noices, which have a negative impact on the fan’s performance and on the environment. Reducing the acoustic surface power will assist in building improved designs that comply with standards and regulations in achieving a more quiet environment. The usage of computational fluid dynamics (CFD), with support of mesh morphing, can provide simulation study for optimizing the shape of a fan blade to reduce the aeroacoustic effects. The investigation process will assist in examining and analyzing the acoustic performance of the prototype, impact of different parameters, and make a solid judgement about the model performance for improvement and optimization.

Formula SAE Collegiate Competition teams now regularly integrate aerodynamic body kits with their vehicles which have significant benefits in producing downforce. This use of body kits (or aero packages) and the improvement to vehicle aerodynamics they provide, have resulted in these systems becoming a necessity for any team wishing to remain competitive in Formula SAE (FSAE). To address this the Lawrence Technological University (LTU) Formula SAE team incorporated an aerodynamic body kit into their 2018 vehicle. Using computational fluid dynamics (CFD) an aerodynamic analysis was performed comparing the efficacy of a car that did not have an aero package to a car that did. Two separate simulation programs were employed to effectively and accurately assess this change. By using both SolidWorks and SimScale software to generate data, the results of each were compared to assess the accuracy of each.

The behavior of different layer designs of a transparent armor (TA) under large strains been investigated. Impacts of light-armor piercing projectile (7.62x51AP) as influencers were tested and analyzed for predicting the TA response when the layers design angles are adjusted. The experimentation allows visualization of damage behavior and the projectile penetration. The visualization techniques are essential models for understanding the mechanisms of interaction between projectile and targeted material design. Ballistic tests results, high-speed photographs and flash-radiographs from experiments with transparent armor were used to establish LS-DYNA simulation module. Transient non-linear dynamic finite-element has been analyzed using LS-DYNA to simulate and validate the experimentation. The penetrative capability of the projectile was assessed in terms of both the ballistic limit velocity against various layer design angles of the TA and air gaps.

This paper presents methods of rapid prototyping design and manufacturing used in the development of a centrifugal pump impeller with curved spacer (CS). In this research subtractive and additive rapid manufacturing methods were applied to create complex curved spacer profiles for testing as part of geometry optimization process for a high speed and high flow rate centrifugal pump impeller. Seven models for the curved spacer were designed and each model was integrated with the bare impeller separately for simulation analysis. One design was selected for manufacturing with applying subtractive and additive processes. In subtractive manufacturing method, the raw material was removed from a solid shaft by a cutting process under digital control from a computer file. The complexity of the modified impeller spacer profiles required the use of expensive CNC machining with five axis capability.

In response to the need for lightweight design in industries, composite materials are increasingly used to replace traditional metal tubes. However, subsurface defects such as voids, delaminations, and microcracks are still remaining common issues in composite pressure tubes. This paper introduces an application of Digital Shearography method in the Non-Destructive Testing (NDT) of high-pressure composite tubes. A new prototype high-pressure composite tube with a working pressure of 1000 psi range is tested using the digital Shearography method. To detect the sub-surface defects, a reference Shearographic phase map is created at 0 psi state, after that the composite tube is pressured using an oil pump, then the second Shearographic phase map is created at the pressured state. By subtracting the two shearographic phase maps created in different pressure state, the sub-surface defects can be identified clearly. The Shearographic NDT result is then compared with CT scan result.

Longitudinal vortex generation is a common technique for enhancing heat transfer performance. It can be achieved by employing small flow manipulators, known as vortex generators (VGs), which are placed on the heat-transfer surface. The vortex generators can generate longitudinal vortices, which strongly disturb the flow structure, and have a significant influence on the velocity and temperature distributions, causing improved thermal transport. In this work, numerical simulations are conducted for a horizontal rectangular channel with and without a pair of longitudinal vortex generators. The vortex generators are fitted vertically on the bottom surface of the channel. The Computational Fluid Dynamics (CFD) analysis aims to acquire a better understanding of the flow structure and heat transfer mechanisms induced by longitudinal vortex generation. The simulation is performed using ANSYS Fluent, and three flow inlet velocities are considered: 1.38 m/s, 1.18 m/s, 0.98 m/s.

AASHTO I-Beam is a standard structural concrete part for bridge sections. The flexural performance of an AASHTO I-Beam is critical for bridge design. This paper presents an application of Digital Image Correlation (DIC) Method in full-scale AASHTO I-Beam flexural performance study. A full-scale AASHTO I-Beam pre-stressed with steel strands is tested by three-point bending method. The full-scale AASHTO I-Beam is first loaded from 0 kips to 100 kips and is then released from 100 kips to 0 kips. A dual-camera 3D Digital Image Correlation (DIC) system is used to measure the deflection and strain distribution during the testing. From the DIC results, the micro-crack generation progress during the loading progress can be observed clearly from the measured DIC strain map. To enable such a large-scale DIC measurement, the used DIC setup is optimized in terms of the optical imaging system and speckle pattern size.

The initiative of this paper is focused on improving the heat dissipation from the pressure wheel of a laser welding assembly in order to achieve a longer period of use. The work examines the effects of different geometrical designs on the thermal performance of pressure wheel assembly during a period of cooling time. Three disc designs were manufactured for testing: Design 1 – a plain wheel, Design 2 – a pierced wheel, and Design 3 – a wheel with ventilating vanes. All of the wheels were made of carbon steel. The transient thermal reaction were compared. The experimental results indicate that the ventilated wheel cools down faster with the convection in the ventilated channels, while the solid plain wheel continues to possess higher temperatures. A comparison among the three different designs indicates that the Design 3 has the best cooling performance.

This paper presents an experimental investigation of flow field instabilities in a centrifugal pump impeller at low flow rates. The measurements of pump hydraulic performance and flow field in the impeller passages were made with a hydraulic test rig. Analysis of Q-ΔP-η data and flow structures in the impeller passages were performed. In the present work, the effect of various flowrates on centrifugal pump impeller performance was analyzed based on pump measured parameters. The impeller’s geometry was modified, with positioning the curved spacer at the impeller suction side. This research investigates the effect of each inlet curved spacer model on pump performance improvement. The hydraulic performance and cavitation performance of the pump have been tested experimentally. The flow field inside a centrifugal pump is known to be fully turbulent, three dimensional and unsteady with recirculation flows and separation at its inlet and exit.

Cooling fans have many applications in industrial and electronic fields that remove heat away from the system. The process of designing a new cooling fan with optimal performance and reduced acoustic sources can be fairly lengthy and expensive. The use of CFD with support of mesh morphing, along with the development of optimization techniques, can improve the acoustic’s performance of the fan model. This paper presents a new promising method which will support the design process of a new cooling fan with improved performance and less acoustic surface power generation. The CFD analysis is focused on reducing the acoustic surface power of a given cooling fan’s blade using the surface dipole acoustic power as the objective function, which leads to an optimized prototype design for a better performance. The Mesh Morpher Optimizer (MMO) in ANSYS Fluent is used in combination with a Simplex model of the broadband acoustic modeling.

Today's strict fuel economy requirement produces the need for the cars to have really optimized shapes among other characteristics as optimized cooling packages, reduced weight, to name a few. With the advances in automotive technology, tight global oil resources, lightweight automotive design process becomes a problem deserving important consideration. It is not however always clear how to modify the shape of the exterior of a car in order to minimize its aerodynamic resistance. Air motion is complex and operates differently at different weather conditions. Air motion around a vehicle has been studied quite exhaustively, but due to immense complex nature of air flow, which differs with different velocity, the nature of air, direction of flow et cetera, there is no complete study of aerodynamic analysis for a car. Something always can be done to further optimize the air flow around a car body.

Bearings are a major component in any rotating system. With continually increasing speeds, bearing failure modes take new unconventional forms that often are not understood. In high speed applications, rolling element forces and gyroscopic moments can be significantly high compared to the applied forces acting on a bearing. Such moments create a “driving” torque causing outer race to creep. In this paper a mathematical model for the dynamics of a rolling element in a high speed bearing is derived. Preload values counterbalancing the torque driving the outer race to rotate can be predicted from this model. An attempt to experimentally measure this torque using a specially designed apparatus with integrated strain gauge torque sensor is also described. Both model and experimental measurements are aimed at understanding, and therefore preventing bearing failures due to outer race (creep) rotations.

In this study, a new nonlinear correlation between Brinell hardness and ultimate tensile strength is proposed. The correlation factor in this case is higher than that found in the current literature. The ultimate tensile strength is replaced by an equivalent hardness expression in the Modified Universal Slopes Method. This change results in fatigue parameters that are predicted using hardness, true fracture ductility, and modulus of elasticity. This new fatigue life prediction approach is compared with the original Modified Universal Slopes method and experimental data in literature. This method is valid for steel with hardness that ranges from 150HB to 660HB. The results show that this method provides better approximations of the strain-life curves when compared with the Modified Universal Slopes and experimental data.

The dynamics of an AWD vehicle is determined by the interactions between the vehicle's wheels and the tire contact surface. Understanding and controlling these interactions drives the vehicle mobility and energy efficiency. In this paper new issues related to tire slippage control are addressed. The paper analytically demonstrates that two tires on the same axle with the same rotational speeds can have different slippages when the normal reaction and inflation pressure vary due to motion conditions. Hence, a new method is proposed to control the rotational velocity of the wheels in a way that provides the same slippages of the tires by accounting for changes in the normal load and tire inflation pressure. This approach is especially beneficial for vehicles with individual (electric) wheel drives which can be individually controlled by introducing the proposed algorithm for controlling both the vehicle linear velocity and the tire slippages.

To stay competitive, new products require faster development time at low cost and good quality. Defense as well as commercial industries are forced to use analytical tools to stay competitive in a tough market. The use of simulation tools and approximation techniques in evaluating product performance during the early stages of the product development has a major impart on the product development efficiency, effectiveness, and lead time. Building physical prototypes of complex systems is expensive and it is difficult and time consuming to develop them. It is extremely beneficial to know as much as possible about the product performance and to optimize its dynamic characteristics before the first physical prototype is built.