Refine Your Search

Topic

Search Results

Viewing 1 to 19 of 19
Technical Paper

Thermodynamic Analysis of Turbocharger for a High Power Density Diesel Engine

2019-01-09
2019-26-0051
Passenger cars claim their presence in market by its pick up, top speed and maximum power of the engine. The study described in this paper is focused on improving the low-end performance of a 4-cylinder 1.6 L diesel engine while meeting the targeted maximum power. To meet the cause turbocharger works as an important element of the engine. A comparative study between regulated two stage turbocharger (R2S) and variable geometry turbocharger (VGT) shows that on a 4-cylinder engine VGT is superior by providing higher boost at 1000 engine rpm full load, than R2S, while in 3-cylinder (same displacement) the opposite effect can be seen. After simulations and iterations, it was confirmed that the in 4-cylinder the exhaust pulse cancellation were leading to a lesser exhaust energy at the turbine inlet. This pulse interaction leads to higher residual gas content which affects the low-end performance.
Technical Paper

Determination of Principal Variables for Prediction of Fuel Economy using Principal Component Analysis

2019-01-09
2019-26-0359
The complexity of Urban driving conditions and the human behavior introduces undesired variabilities while establishing Fuel economy for a vehicle. These variabilities pose a great challenge while trying to determine that single figure for assessment of vehicle’s fuel efficiency on an urban driving cycle. This becomes even more challenging when two or more vehicles are simultaneously evaluated with respect to a reference vehicle. The attempt to fit a generalized linear model, between Fuel Economy as predicted variable and components of a driving cycle as predictor variables produced oxymoronic and counter-institutive results. This is primarily due to existence of multi-collinearity among the predictor variables. The context of the study is to consider the event of driving on a cycle as a random sampling experiment. The outcome of a driving cycle is summarized into a list of predictor variables or components.
Technical Paper

Development of Low Cost FEAD System with Stretch Fit Belt

2018-07-09
2018-28-0064
In Current scenario all Vehicle Manufacturer are looking towards cost effectiveness in their product development without compromising product quality and performance. With this reference, development of low cost FEAD (Front End Accessory Drive) system with stretch fit belt & idlers for multiple accessories has emerged as one of the alternative smart engineering solution against the FEAD with auto tensioner. The beauty of this low cost FEAD system is not only the cost saving but also the long lasting performance without affecting component life. In the current work, development of a low cost FEAD for 3 cylinder 1.5 litre diesel engine has been presented. It was one of the challenges to introduce stretch fit belt for 3 cylinder engine considering the high torsional vibration. The performance of this FEAD system was evaluated in terms of accessories pulley slip and belt flapping. The component durability was assessed both at engine as well as at vehicle level.
Technical Paper

Fatigue Failure Analysis of Diesel Engine Connecting Rod

2018-07-09
2018-28-0067
Connecting rod of a high performance reciprocating internal combustion engine is one of the critical components exhibiting complex motion. This is subjected to both compressive load due to combustion force as well as tensile load due to inertia of the moving components. These loadings are cyclic in nature and the component is highly prone to fatigue failure if not deigned or manufactured carefully. Therefore connecting rods are designed and manufactured with high degree of precision for infinite loading cycle. But failures in connecting rod is often reported which is associated to either fatigue, bending, bearing failure or assembly faults. This study deals with one of such failure of connecting rod reported during fatigue testing. Failures occurred at around 1 million fatigue loading cycle as against target life of 5 million cycles. The present study represents the investigations done for engine connecting rod and with a view to identify the root cause of failure.
Technical Paper

Comparative Studies of Different VGT Designs on Performance and Smoke of CRDe Engine

2018-07-09
2018-28-0074
Diesel engines have occupied a significant position in passenger car applications in the present automotive sector. Turbochargers find a very prominent role in diesel engines of all applications in order to achieve desired power and better fuel economy. Gaining higher torque at lower engine speeds with low smoke levels is a very tough task with fixed geometry turbochargers due to availability of lower air mass resulting in higher smoke emissions. Variable geometry turbochargers are capable of providing better torque at lower speeds and reduced smoke emissions on Common Rail Diesel engines. The Variable Geometry Turbocharger types used in this study are straight profile nozzle vanes (sample A) and curved profile nozzle vanes (sample B). The curved profile vanes as seen in sample B results in reduced variation of circumferential pressure distortions.
Technical Paper

DMADV Approach for Engineering Optimization and Quality - Application and Adaptability in Indian Automobile Industry

2017-07-10
2017-28-1930
Indian Automobile Industry has started using Six Sigma for Vehicle Design and process improvement to compete with Global competition. This Paper describes how the Tools of Six Sigma shall be used as an Effective Tool for both redefining the Design and the Process Improvement. This Paper talks on the evolution of DMADV approach in Indian Automobile Industry compared to the related Trends in Other Manufacturing Sectors. The Author describes how the warranty failures in Commercial Segment Vehicle Category which was the selling talk for the Competition was addressed in Leading Indian Automobile OEM. As this Failure was adversely impacting customer satisfaction and no solution seemed forthcoming, top Management indicated to use a radically different approach to solve the problem within a years’ time.
Technical Paper

Low Rolling Resistance Tires and Their Impact on Electric Vehicles

2017-07-10
2017-28-1941
This paper details the methodology used to show the importance of Low rolling resistance tires in Electric Vehicles. Fuel efficiency and range is paramount with most of the electric vehicle buyers. Although many people are now becoming aware of low rolling resistance tires but its development started way back in 1990’s. It is always challenging to achieve low rolling resistance in smaller tires of size 12 inch or 13 inch along meeting the other critical vehicle parameters such as ride and handling, NVH, durability and many more. The reduction in rolling resistance can also affect the traction properties of tires. In case of very low rolling resistance tires the traction will be very less but it can badly affect the other vehicle parameters. Selection of tires further depend upon the RWUP (Real World Usage Profile). It means the vehicle is targeted for which region and what is the condition of roads there.
Journal Article

Acoustic Analysis of a Compact Muffler for Automotive Application

2017-06-17
2017-01-9550
A production muffler of a 2.2 liter compression ignition engine is analyzed using plane wave (Transfer Matrix) method. The objective is to show the usefulness of plane wave models to analyze the acoustic performance (Transmission Loss, TL) of a compact hybrid muffler (made up of reactive and dissipative elements). The muffler consists of three chambers, two of which are acoustically short in the axial direction. The chambers are separated by an impervious baffle on the upstream side and a perforated plate on the downstream side. The first chamber is a Concentric Tube Resonator (CTR). The second chamber consists of an extended inlet and a flow reversal 180-degree curved outlet duct. The acoustic cavity in the third chamber is coupled with the second chamber through the acoustic impedances of the end plate and the perforated plate.
Technical Paper

Assessment of Cabin Leakage on Thermal Comfort and Fuel Efficiency of an SUV

2016-04-05
2016-01-0259
The main function of an air conditioning system in a vehicle is to provide the thermal comfort to the occupant at minimum possible energy consumption in all environmental conditions. To ensure the best possible thermal comfort, air conditioning system is optimized on various parameters like heat load, air flow distribution, glass area, trim quality, insulations and cabin leak rate. A minimum cabin leakage is regulatory requirements to ensure the air quality of cabin. Anything above the minimum cabin leak rate ultimately turn into reduced thermal comfort and additional energy consumption. The additional energy consumption to maintain the required thermal comfort in the cabin due to cabin leakage affects the fuel efficiency severely. In the present study, the effect of cabin leakage on fuel efficiency and thermal comfort is studied in details by varying the cabin leakage through mechanical means. The experiments are carried out in normal environmental condition and road condition.
Technical Paper

Cost and Weight Efficient Differential Housing for Off-Road Vehicles

2016-02-01
2016-28-0133
Differential in Gear Box play vital role in Tractors for assisting it in turning and also to take straight path. Light weight machine always have advantage in terms of fuel economy and performance. Weight optimized rotating part have additional benefits of saving power loss, against stationary dead weight. Differential Housing is such a part, which rotates during the vehicle motion and torque transmission. [1] This paper describes a method by which weight of the Differential Housing is optimized. In this particular body of work, additional constraints of avoiding any change in existing cold forged parts like Bevel Gear & Pinion. This also have additional benefit of enhanced flow of Oil inside Differential Housing for better lubrication of Bevel Gears and Pinion. This resulted in weight saving of Differential Housing and finally fuel economy of Tractor.
Technical Paper

Optimization of Vehicle Electrical Energy Consumption

2015-09-29
2015-01-2882
This paper focuses on optimizing the electrical energy consumption of vehicle. By introduction three concepts. 1) Innovative speed control logic for radiator fan motor according to vehicle speed and air flow through radiator. 2) Introducing regeneration of energy from radiator fan motor while free running and deceleration of vehicle. 3) Using BLDC motors (generation mode and motoring mode) in radiator and blower motors. About 50 % of total electrical energy consumption of vehicle is contributed by radiator fan motor and blower motor (proven data by performing alternator charge balance test during NEDC cycle). By introducing above three concepts, 50 % electrical energy consumption can be reduced to 25 - 30 %, which gives more than 3.5 % fuel economy improvement and more than 10 gmCO2 reduction per kilometer. Further reduction in conducted emission at motor level, soft starting for radiator fan and blower motor and elimination of high inrush current.
Technical Paper

Computational and Experimental Investigations to Improve Performance, Emissions and Fuel Efficiency of a Single Cylinder Diesel Engine

2015-01-14
2015-26-0099
From International Energy Statistics (IES) survey, China, US and India are top three countries in emitting CO2 emissions. Further, worldwide national governments are focused to control CO2 emissions at source by stringent regulatory limits. OEMs and Research laboratories are working on several technology options such as advanced fuel injection system, optimizing in cylinder combustion system, thermal management and reduced engine friction to meet this legal requirements. In this paper, research work focused on improving combustion system through selection optimum bowl geometry and increasing volumetric efficiency through valve timings, profile and intake system using both 1D and 3D-CFD numerical approach. The main objective of this approach to utilize fossil fuel to its maximum potential in a single cylinder Naturally Aspirated (NA) water cooled engine with CRDI.
Technical Paper

High Performance EGR Cooler Selection and its Fouling Behavior for a HSDI Diesel Engine

2015-01-14
2015-26-0087
Selection of EGR system is very complex for a particular engine application. The performance of the EGR system depends highly on the Cooler Heat Transfer Efficiency. Cooler effectiveness drops over a period of operation due to soot deposition, HC condensation, and fuel quality. This phenomenon is called as Cooler Fouling. Fouling cannot be avoided completely but the level of performance drop over time has to be studied and minimized. The minimum pressure drop and the highest efficiency in fouled condition is the target for selection of a cooler. In this study, various parameter combinations like tube shape and profile, tube length, number of tubes, tube diameter, and pitch of corrugations, which influence the cooler performance were tested. A better understanding of each of its effect on cooler effectiveness and fouling behavior was obtained. The tube shape was changed from rectangular to circular, also from smooth surface to corrugate.
Technical Paper

Design For Affordability -Composite Running Board

2015-01-14
2015-26-0070
Light weighting is the Current trends in automotive to achieve better fuel economy which helps for meeting fuel economy standards & to offset the higher fuel prices. Thus there is a need to develop composite running board which is light weight & structurally sound enough to meet the performance. The present paper provides a composite running board assembly for an automobile. The running board assembly includes a board, an insert body and a plurality of brackets. Upon stepping of a passenger on the board, the board transfers load on the insert body which subsequently transfers the load to the plurality of brackets thus facilitating even distribution of the load on the automobile body. This paper also put lights on the use of improved TRIZ application - an approach to inventive problem solving for designing highly affordable & light weight running board. The cost & weight reduction achieved with innovative design is about 40 % & 35 % comparing to existing cost & weight.
Technical Paper

Development & Customization of Test Cases for Start-stop Functionality to Achieve On-road Robustness

2013-11-27
2013-01-2875
The Micro-hybrid technology otherwise called as stop start system offers a significant improvement in fuel economy particularly in urban driving conditions, where more often the engine idles unnecessarily at traffic signals/jams. Micro-hybrid technology stops the engine at traffic signals/jams and starts the engine automatically on clearance of traffic signals/jams leading to reduced fuel consumption and emissions. This is achieved by monitoring several vehicle and engine parameters through appropriate sensing elements. In this study, the system architecture and functional definitions of start/stop system is defined. Equivalence class, boundary value and decision-table testing are used to generate test cases. On generation of test cases, their relevance on on-road robustness and scope for optimization towards time/efforts are analyzed. In the process, a matrix of different conditions and criteria are formulated. Under these conditions, the system behavior is evaluated.
Technical Paper

Selection of Gear Ratio for Smooth Gear Shifting

2012-09-24
2012-01-2005
Manual transmissions are characterized by gear ratios that are selectable by locking selected gear pairs to the output shaft inside the transmission. Top gear is selected to get a maximum speed and is limited by the engine power, speed and the fuel economy. Lower gears are selected to get maximum speed at maximum gradient. Lower gears are also expected to give creeping speed to avoid usage of clutch and brake in city traffic. Selection of intermediate gears is such that it provides a smoother gear shift. Gear spacing is done in geometric progression. Spacing between the higher gears is usually closer than in the lower gears because drivers shift more often between the lower gears. This is opposed to the conventional idea of progressive spacing where higher gears had more space between them. An objective method is provided for selecting gear ratios for use in vehicle transmission having multiple selectable gears.
Technical Paper

Hybrid Oil Sump for CI Engine

2011-09-11
2011-24-0135
Recently fuel economy and stringent emission norms are the ever growing concern in automotive global scenario. So, automotive engineers are constantly seeking new cost effective methodologies and techniques to achieve considerable weight reduction and improved performance. Nowadays Automotive OEMs are using Aluminum Oil sump (which is a structured part of an engine and supports considerable amount of transmission housing weight) for better emission, reducing the engine height, engine weight and NVH levels. Our present work reveals the concept of ‘Hybrid oil sump’ which made by sheet metal and aluminum in such a way that weight and cost reduced by 20% and 30 % respectively, without compromising NVH and strength properties. Exactly it deals the iteration part of design to arrive the optimum model, various structural modifications since it carries considerable amount of weight of transmission.
Technical Paper

Turbocharging a Small Two Cylinder DI Diesel Engine - Experiences in Improving the Power, Low End Torque and Specific Fuel Consumption

2011-09-11
2011-24-0133
Turbocharged common rail direct injection engines offer multiple benefits compared to their naturally aspirated counterparts by allowing for a significant increase in the power and torque output, while simultaneously improving the specific fuel consumption and smoke. They also make it possible for the engine to operate at a leaner air/fuel mixture ratio, thereby reducing particulate matter emission and permitting higher EGR flow rates. In the present work, a two cylinder, naturally aspirated common rail injected engine for use on a load carrier platform has been fitted with a turbocharger for improving the power and torque output, so that the engine can be used in a vehicle with a higher kerb weight. The basic architecture and hardware remain unchanged between the naturally aspirated and turbocharged versions. A fixed geometry, waste gated turbocharger with intercooling is used.
Technical Paper

Experiences in Cold Start Optimization of a Multi-Purpose Vehicle Equipped with 2.2L Common Rail Diesel Engine

2011-04-12
2011-01-0124
High speed diesel engines are difficult to start in cold conditions (at subzero temperature) because the cylinder head and cylinder block absorbs heat of compression and thus preventing ignition due to the high surface to volume ratio. Also the coolant and the engine oil become viscous at subzero temperature and make the condition unfavorable for starting. Combustion optimization along with the help of a heating aid can make these engines to start quickly without any engine misbehavior. Cold startability is the ability of an engine to start within a specified time and continue to run without any malfunctioning. Combustion instability will lead to the misfiring of the engine unless it is calibrated properly. The European countries are subjected to a minimum temperature of -20°C to -25°C. So the intention of this work is to optimize the cold startability of Mahindra's Multi-Purpose Vehicle (MPV) up to -25°C which is to be sold in European countries.
X