Search Results

To achieve carbon-neutrality, internal combustion engines need to further improve their thermal efficiency to reduce CO2 emissions. To accomplish this, it is necessary to quantify and enhance five factors that control indicated thermal efficiency: compression ratio, specific heat ratio, combustion duration, combustion timing, and heat transfer to wall. In this work, quantitative targets for each factor were defined, which were derived from a simulation that considered the influence of heterogeneity of diesel combustion on thermal efficiency. The simulation utilized a two-zone combustion model. In particular, the targets for the combustion duration, combustion timing and heat transfer to wall were increased significantly compared to those for a conventional engine, in anticipation of an expansion of the load range of premixed charge compression ignition (PCI) combustion to higher loads.

Automobiles will have to be applied strict regulations such as Euro7 against PM, HC, CO. The generation of these components are related to fuel deposition to the wall surface of the combustion chamber. Therefore, the fuel injection model of engine combustion CFD requires accurate prediction about the deposition and vaporization of fuel on the combustion chamber. In this study, multiphase flow numerical analysis that simulates fuel behavior on the wall surface was conducted first. Then, two model formulae about the contact area and the heat flux of a liquid film was constructed based on the result of multiphase flow numerical analysis method. Finally, the new film heat transfer model was constructed from these model formulae. In addition, it was confirmed that new heat transfer model can predict the liquid film temperature obtained by multiphase flow numerical analysis method accurately.

As a technology to reduce the heat loss of engines, heat insulation coating to the surface of combustion chamber has been received a lot of attention. In order to maximize the thermal efficiency improvements by the technology, it is important to clarify the location where heat insulation coating can reduce heat loss more effectively, considering the impact on abnormal combustion etc. In this study, transient behavior of wall heat flux distribution on the piston was analyzed using 3D Computational Fluid Dynamics (CFD) for three combustion modes (spark ignition combustion (SI), homogenous charge compression Ignition (HCCI) and spark controlled compression ignition (SPCCI)).

To get a better understanding of the characteristics of the high pressure gasoline sprays impinging on a wall, a fundamental study was conducted in a high-temperature high-pressure constant volume vessel under the simulated engine conditions of in-cylinder pressures, temperatures, and wall temperatures. The injection pressure was varied from 20 to 120 MPa. The spray tip penetration, vapor mass distribution, and vaporization rate were quantitatively measured with the laser absorption-scattering (LAS) technique. The velocity fields of the wall-impinging sprays under vaporizing conditions were measured with the particle image velocimetry (PIV) technique using silicone oil droplets as tracers. The effects of injection pressure and spray/wall interactions on spray characteristics were investigated. The results showed that the increased injection pressure improved penetration, vaporization, and turbulence of the sprays.

It was important for predicting wall heat flux to apply wall heat transfer model by taking into account of the behavior of turbulent kinetic energy and density change in wall boundary layer. Although energy equation base wall heat transfer model satisfied above requirements, local physical amounts such as turbulent kinetic energy in near wall region should be applied. In this study, in order to predict wall heat transfer by zero dimensional analysis, how to express wall heat transfer by using mean physical amounts in engine combustion chamber was considered by experimental and numerical approaches.

The method described in this paper has been proposed to analyze the heat balance of diesel combustion from engine measurement data considering the heterogeneity of this type of combustion with use of a two-zone model composed of unburned and burned zones. This method is intended for practical application to an engine bench test during an engine development process and is characterized by the following features: A representative excess air ratio of the burned zone is set and assumed to be constant throughout the combustion period, and the ratio is estimated from NOx emission amount. The authors performed heat balance analyses on engine measurement data using the proposed method and made a comparison with the results of analyses that assumed a combustion chamber to be one homogenous zone.

In the development of fuel tank systems, it is important to maintain fuel system integrity even if a car accident occurs. When a fuel tank undergoes a sudden change in velocity, the fuel starts to move and deforms the tank walls and baffle plates, and then the deformation changes the flow pattern of fuel. Because interaction of fuel with tank components is the main cause of fuel spillage upon crash, it is important to predict complex fluid-structure interaction responses at an early stage of crash safety development with a multiphysics simulation. Development of the multiphysics simulation technique was conducted stepwise by examining “fluid motion” and “tank deformation.” First, a sled test of a rigid-wall tank with observation window was conducted to evaluate the fluid motion inside the tank. A numerical model was developed based on an ALE (Arbitrary Lagrangian Eulerian) algorithm for the fluid and a Lagrangian algorithm for the structure.

Heat loss is more critical for the thermal efficiency improvement in small size diesel engines than large-size diesel engines. More than half of total heat energy in the internal-combustion engine is lost by cooling through the cylinder walls to the atmosphere and the exhaust gas. Therefore, the new combustion concept is needed to reduce losses in the cylinder wall. In a Direct Injection (DI) diesel engine, the spray behavior, including spray-wall impingement has an important role in the combustion development to reduce heat loss. The aim of this study is to understand the mechanism of the heat transfer from the spray and flame to the impinging wall. Experiments were performed in a constant volume vessel (CVV) at high pressures and high temperatures. Fuel was injected using a single-hole injector with a 0.133 mm diameter nozzle. Under these conditions, spray evaporates, then burns near the wall. Spray/flame behavior was investigated with a high-speed video camera.

A road vehicle’s cornering motion is known to be a compound motion composed mainly of forward, sideslip and yaw motions. But little is known about the aerodynamics of cornering because little study has been conducted in this field. By clarifying and understanding a vehicle’s aerodynamic characteristics during cornering, a vehicle’s maneuvering stability during high-speed driving can be aerodynamically improved. Therefore, in this study, the aerodynamic characteristics of a vehicle’s cornering motion, i.e. the compound motion of forward, sideslip and yaw motions, were investigated. We also considered proposing an aerodynamics evaluation method for vehicles in dynamic maneuvering. Firstly, we decomposed cornering motion into yaw and sideslip motions. Then, we assumed that the aerodynamic side force and yaw moment of a cornering motion could be expressed by superposing linear expressions of yaw motion parameters and those of sideslip motion parameters, respectively.

Coating the heat insulation materials on the combustion chamber walls is one of the solutions to reduce the cooling loss of internal combustion engines. In order to examine the coatings, the evaluation of the heat transfer coefficient and the analysis of the heat transfer phenomena on the heat insulated walls are important. Firstly, the highly-responsive wall temperature sensor is developed, and the instantaneous wall heat flux is measured to evaluate the heat transfer coefficient on the heat insulated walls. The results show that the Nusselt number on the heat insulated walls is less influenced by the Reynolds number variation than that on the metal walls. Secondly, the high speed µ-PIV is employed to analyze the various turbulent flow characteristics. The results show that the turbulent dissipation on the heat insulated walls is smaller than that on the metal walls.

The purpose of this study is to define requirements for technological and business success in the world's first implementation of Reverse-Supply-Chain, in which bumper materials of end-of-life vehicles (ELV) are recycled for use as ingredients in new bumper materials. In Japan, ELVs are recovered following to the government regulation. About 20% (700,000 ton) of such collected ELVs are automotive shredder residues (ASR), most of which are burnt as fuel or used as landfill trash. ASRs are mainly plastics, which are largely used as materials of bumpers. The reverse-supply-chain was started as a small business by a collaboration between the car manufacture (Mazda), dismantler, and resource-recycling business operator, and enhanced by the development of easy-to-recycle bumpers, technologies of paint removal from crushed bumpers and sorting-out, a material quality control method, and improvement in transportation efficiency.

The problem of predicting the quality of weld is critical to manufacturing. A great deal of data is collected under multiple conditions to predict the quality. The data generated at Daimler Chrysler has been used to develop a model based on grammatical evolution. Grammatical Evolution Technique is based on Genetic Algorithms and generates rules from the data which fit the data. This paper describes the development of a software tool that enables the user to choose input variables such as the metal types of top and bottom layers and their thickness, intensity and speed of laser beam, to generate a three dimensional map showing weld quality. A 3D weld quality surface can be generated in response to any of the two input variables picked from the set of defining input parameters. This tool will enable the user to pick the right set of input conditions to get an optimal weld quality. The tool is developed in Matlab with Graphical User Interface for the ease of operation.

The aim of this research was to find vehicle characteristics including stiffness that is effective for compatibility performance. Compatibility is said to be affected by three factors: vehicle mass, geometry and stiffness (1, 2). Of these factors, stiffness has more flexibility at the design stage than vehicle mass and geometry which are limited by the vehicle application. However, the stiffness is assumed to have a conflict issue between the self-protection and the partner-protection (3). In this research, it was analyzed comprehensively how some defined factors such as stiffness, mass, crash stroke and other vehicle characteristics indices relate to each occupant injury rate of the case and its partner vehicle in the real-world accidents. Both “front-to-front” and “front-to-side” crash occupants were covered.

Low frequency torsional vibrations can be a significant source of objectionable vehicle vibrations and in-vehicle boom, especially with changes in engine operation required for improved fuel economy. These changes include lower torque converter lock-up speeds and cylinder deactivation. This paper has two objectives: 1) Examine the effect of increased torsional vibrations on vehicle NVH performance and ways to improve this performance early in the program using test and simulation techniques. The important design parameters affecting vehicle NVH performance will be identified, and the trade-offs required to produce an optimized design will be examined. Also, the relationship between torsional vibrations and mount excursions, will be examined. 2) Investigate the ability of simulation techniques to predict and improve torsional vibration NVH performance. Evaluate the accuracy of the analytical models by comparison to test results.

Brake torque variation is a source of objectionable NVH body/chassis response. Such input commonly results from brake disk thickness variation. The NVH dynamic characteristics of a vehicle can be assessed and quantified through experimental modal testing for determination of mode resonance frequency, damping property, and shape. Standard full vehicle modal testing typically utilizes a random input excitation into the vehicle frame or underbody structure. An alternative methodology was sought to quantify and predict body/chassis sensitivity to brake torque variation. This paper presents a review of experimental modal test methodologies investigated for the reproduction of vehicle response to brake torque variation in a static laboratory environment. Brake caliper adapter random and sine sweep excitation input as well as body sine sweep excitation in tandem with an intentionally locked brake will be detailed.

This paper describes the application of the modal compliance method to a complex structure such as a vehicle body in white, and the extension of the method from normal modes to the complex modes of a complete vehicle. In addition to the usual bending and torsion calculations, the paper also describes the application of the method to less usual tests such as second torsion, match-boxing and breathing. We also show how the method can be used to investigate the distribution of compliance throughout the structure.

This paper identifies the difference in powertrain cooling system content levels using a nominal and a +3 Standard deviation maximum temperature design approach. Variation simulation analysis tools are used along with a 1-D cooling system performance model to predict resulting temperature distribution for different combinations of input variable populations. The analysis will show differential in powertrain cooling system content, mass, and impact to fuel economy for a nominal vs. +3 sigma design approach.

Brake judder, which is a low frequency excitation of the suspension and thus, the body structure during low-G braking, is mainly felt at the steering wheel and throughout the vehicle structure. Brake judder is a problem that costs manufacturers millions of dollars in warranty cost and undesirable trade offs. The magnitude of judder response depends not only on the brake torque variation, but also on the suspension design character-istics. This paper discusses the judder simulation process using ADAMS software to investigate the suspension design sensitivity to the first order brake judder performance. The paper recommends “tuning knobs” to suspension designers and vehicle development engineers to resolve issues in the design and development stages. Various suspension design varia-bles including geometry and compliances as well as brake related characteristics were investigated.

This study attempts to develop a correlation between an airflow motion number, combustion burn rates, and initial flame kernel development. To accomplish this task, several motion plates were evaluated on a flowbench in order to calculate a motion number that would represent the dynamic motion in the combustion chamber. Afterwards, the plates were tested on a spark ignited engine at several part throttle conditions while gathering cylinder pressure measurements. These cylinder pressure measurements would then yield the combustion burn rates for each plate. In addition to the combustion measurements, the flame kernel growth, velocity and direction of the flame kernel were measured using an AVL Visio-flame. Finally, the data was evaluated and an attempt to correlate the motion number of the plates to the different measurements for describing combustion was made.

To mitigate head impact injuries of vehicle occupants in impact accidents, the FMVSS 201 requires padding of vehicle interior so that under the free-moving-head-form impact, the head injury criterion (HIC) is below the limit. More recently, pedestrian head impact on the vehicle bonnet has been a subject being studied and regulated as requirements to the automobile manufacturers. Over the years, the square wave has been considered as the best waveform for head impacts, although it is impractical to achieve. This paper revisits the head impact topic and challenges the optimality of aiming at the square waveform. It studies several different simple waveforms, with the objective to achieve minimal HIC or minimal crush space required in head-form impacts. With that it is found that many other waveforms can be more efficient and more practical than the square wave, especially for the pedestrian impact.