Search Results

The automotive refrigerant system can occasionally exhibit an excessive noise out of air-conditioner (A/C) vents during vehicle’s developments. If the vehicle has been parked for long hours in summer and the A/C system is turned on, sometimes hissing noise is induced by the refrigerant flow. In order to understand the mechanism, a lot of bench and vehicle tests were conducted. However, there is still not enough to understand the physical behavior in detail. Therefore, for the first step, the visualization method to capture the behavior of multi-phased refrigerant flow jet inside the pipe was proposed with a high-speed camera, some light devices and acrylic test piece. In addition, image analysis to quantify the flow regime from a series of observed snapshots. Using proposed method, the correlation study between flow and noise was performed at A/C bench test. As a result, different flow features such as the velocity can be observed in the occurrence of the noise or not.

Improving fuel efficiency often affects NVH performance. Modifying a vehicle’s design in the latter stages of development to improve NVH performance is often costly. Therefore, to optimize the cost performance, a Multi-Attribute Balancing (MAB) approach should be employed in the early design phases. This paper proposes a solution based on a unified 1D system simulation model across different vehicle performance areas. In the scope of this paper the following attributes are studied: Fuel economy, Booming, Idle, Engine start and Drivability. The challenges to be solved by 1D simulation are the vehicle performance predictions, taking into account the computation time and accuracy. Early phase studies require a large number of scenarios to evaluate multiple possible parameter combinations employing a multi-attribute approach with a systematic tool to ease setup and evaluation according to the determined performance metrics.

Without engine noise, the cabin of an electric vehicle is quiet, but on the other hand, it becomes easy to perceive refrigerant-induced noise in the automotive air-conditioning (A/C) system. When determining the A/C system at the design stage, it is crucial to verify whether refrigerant-induced noise occurs in the system or not before the real A/C systems are made. If refrigerant-induced noise almost never occurs during the design stage, it is difficult to evaluate by vehicle testing at the development stage. This paper presents a 1D modeling methodology for the assessment of refrigerant-induced noise such as self-excitation noise generated by pressure pulsation through the thermal expansion valve (TXV). The GT-SUITE commercial code was used to develop a refrigerant cycle model consisting of a compressor, condenser, evaporator, TXV and the connecting pipe network.

Tip-in/Tip-out of the accelerator pedal generates transient torque oscillations in the driveline. These oscillations may be amplified by P/T, suspension and body modes and will eventually be sensible at the receiver side in the vehicle, for example at the seat or at the steering-wheel. The forces that are active during this transient excitation are influenced by non-linear effects in both the suspension and the power train mounts. In order to understand the contribution of each of these forces to the total interior target response (e.g. seat rail vibration) a detailed investigation is performed. Traditional force identification methods are not suitable for low-frequent, transient phenomena like tip-in/tip-out. Mount stiffness method can not be used because of non-linear effects in the P/T and suspension mounts. Application of matrix inversion method based on trimmed body vibration transfer functions is not possible due to numerical condition problems.

Flows around a forward facing step and a fence are simulated on structured grid to estimate aerodynamic noise by using direct simulation. Calculated results of sound pressure level show quantitatively good agreement with experimental results. To estimate aerodynamic noise from 3D complex geometry, a simplified side mirror model is also calculated. Averaged pressure distribution on the mirror surface as well as pressure fluctuations on the mirror surface and ground are simulated properly. However, calculated result of sound pressure level at a location is about 20dB higher than experiment due to insufficient spatial resolution. To capture the propagation of sound waves, more accuracy seems to be required.

Knock noise induced by automotive shock absorbers has serious influence on driving comfort and vehicle quality. Some research focusing on knock noise had been introduced in the past. However there is the unidentified phenomenon that has been unnoticed. This paper describes the new theory to clarify one of the unidentified phenomenon and proposes the equation for stability assessment which is useful on designing stage of development. First of all, the characteristics of the unidentified rod vibration of shock absorbers are investigated experimentally. Second, the new theory is established on the basis of the non-linear physical model with friction forces between piston and cylinder. This theory shows that the unstable vibration, so called the Self Excited Vibration, can be induced by not only friction property but also structure of rod and piston. Third, the equation for stability assessment, which is useful on designing stage of development, is proposed on the basis of new theory.

In the previous paper(1), the authors reported the calculation method they developed for predicting the idling rattle in manual transmissions. This method provides data that represent noise levels to which human ear is not sensitive by numerical values. In the study described in this paper, the authors attempted to produce audible noise through a speaker by the following process: create time-series data of fluctuation in the angular acceleration obtained by the calculation (which is considered to correspond to rattle noise); create next-stage data by applying convolution of a transmission case's vibration transfer characteristics filter obtained by the experiment to the above-mentioned time-series data; convert the filtered data into a wave file; and then input the file to a personal computer to obtain audible sound as output. The audible noise thus produced provides a means of evaluating the level and nature of noise in the way humans naturally experience it.

It is generally known that the idling rattle in manual transmissions is caused by gear tooth portions that make repeated impact-generating vibrations in the backlashes. These vibrations result from rotational fluctuations of the flywheel induced by combustion in the engine. In the study reported here, the authors constructed an experimental setup using rotary encoders and a transient torsional angle converter that allowed the long-awaited direct measurement of impact-generating vibrations in the backlashes. Using this experimental result, the following ideas that the authors must pay attention for the numerical simulation are obtained. That is, transmission drag torque is to be input and treated as the offset value in the torque value of the torsional characteristics in the clutch disc, and coefficients of attenuation have great influence upon the calculation result.

To reduce the idling rattle of manual transmissions, the computer simulation has been utilized. However, the conventional simulation model could not express properly the relationship between the transmission oil temperature and the rattle noise level, especially in case of transmission with backlash eliminator in constant mesh gears. In this study, the authors carried out detail experiments investigating the motion of each part in the transmission. Based on the experimental results, an additional mass representing all constant mesh speed gears supported on plain or rolling element bearings was introduced to the simulation model. Using the improved model, it was confirmed that the calculated RMS value of the fluctuation in countershaft angular acceleration corresponds to the experimental rattle noise level.

As part of the International Lubricant Standardization and Approval Committee's (ILSAC) goal of developing a global automatic transmission fluid (ATF) specification, members have been evaluating test methods that are currently used by various automotive manufacturers for qualifying ATF for use in their respective transmissions. This report deals with comparing test methods used for determining torque capacity in friction systems (shifting clutches). Three test methods were compared, the Plate Friction Test from the General Motors DEXRON®-III Specification, the Friction Durability Test from the Ford MERCON® Specification, and the Japanese Automotive Manufacturers Association Friction Test - JASO Method 348-95. Eight different fluids were evaluated. Friction parameters used in the comparison were breakaway friction, dynamic friction torque at midpoint and the end of engagement, and the ratio of end torque to midpoint torque.