Search Results

In-cylinder sampling appears to be the only available means for obtaining detailed information of the diesel combustion process. This information is necessary to understand pollutant formation because of the intimate relationship between formation rates and local cylinder conditions. This paper discusses efforts to (1) examine and improve sampling valve design, (2) evaluate potential effects of the valve and the sampling system on sample composition, (3) find methods to extract useful information from sampling data. Sampling hardware is currently being used to study combustion in engines, but further work is needed to quantify the influence of hardware and procedures on sample composition and to design experiments to provide data containing maximum information.

A single-wheel trailer has been designed and built to study the origins of tire noise and its basic characteristics. The single test tire, nominally the 10.00/20 size usually mounted on large trucks and semitrailers, is located 12.2 m (40 ft) behind the rear axle of the towing vehicle to isolate it from other noise sources. Reflective surfaces that could interfere with noise measurements are minimized by the high, single-beam construction of the trailer. The towing vehicle is modified to reduce its noise and wake in the vicinity of the test tire, which can be loaded to 22.2 kN (5000 lb) by dead weights and rolled at expressway speeds. Because of its unusual configuration, the dynamic behavior of the trailer was studied prior to design to help determine several design parameters and show that the trailer would follow well. Extensive stress analyses of the trailer beam and other structural elements were also required.

During development of the General Motors rotary engine, the lubricant was recognized as important to its success because certain lubricants produced deposits which tended to stick both side and apex seals. Consequently, it was decided to develop a rotary engine-dynamometer test, using a Mazda engine, which could be used for lubricant evaluation. In an investigation using an SE engine oil with which there was rotary engine experience, engine operating variables and engine modifications were studied until the greatest amount of deposits were obtained in 100 h of testing. The most significant engine modifications were: omission of inner side seals, plugging of half the rotor bearing holes, pinning of oil seals, grinding of end and intermediate housings, and using a separate oil reservoir for the metering pump. Using this 100 h test procedure, three engine oils and five automatic transmission fluids were evaluated.

Hydrogen-supplemented fuel was investigated as a means of extending lean operating limits of gasoline engines for control of NOx. Single-cylinder engine tests with small additions of hydrogen to the fuel resulted in very low NOx and CO emissions for hydrogen-isooctane mixtures leaner than 0.55 equivalence ratio. Significant thermal efficiency improvements resulted from the extension beyond isooctane lean limit operation. However, HC emissions increased markedly at these lean conditions. A passenger car was modified to operate at 0.55-0.65 equivalence ratio with supplemental hydrogen. Vehicle emissions, as established by the 1975 Federal Exhaust Emissions Test, demonstrated the same trends as the single-cylinder engine tests. The success of the hydrogen-supplemented fuel approach will ultimately hinge on the development of both a means of controlling hydrocarbon emissions and a suitable hydrogen source on board the vehicle.

Noise produced by automotive ignition systems can deteriorate the performance of nearby communication systems. An important step toward alleviating this difficulty is to characterize the ignition noise. Measurements have been made of the noise peak amplitude distribution of a number of identically equipped vehicles over a fixed period of time. Both vertical and horizontal polarizations were used, and measurements were made at two frequencies, 145 and 230 MHz. These statistics were then compared to various probability distributions to attempt to characterize the amplitude distribution of the noise. The distributions studied were: the log-normal, the exponential, the Rayleigh, and the Weibull distributions. It was concluded that the best fit was provided by the Weibull distribution. The parameters of the best fitting distribution are primarily a function of the antenna's polarization, with frequency having only a minor effect.

This paper evaluates the tendency of lip seals to fracture in a test apparatus in which dynamic runout is 0.010 in and the temperature is cycled between -30 and 0 F. Seals made of eight different polyacrylate polymers were soap-sulfur cured with various types and amounts of carbon black. Physical tests included room-temperature flexibility defined by Young's modulus at small strains, standard tensile tests at room temperature, flexibility at sub-zero temperatures determined by a Gehman test, and sub-zero starting torques of the seals. Primary determinant of successful fracture resistance is a low starting torque resulting from good low-temperature flexibility. The effect of adding graphite to some of these formulations is described and some current commercially available seals are evaluated.

This paper summarizes an analysis, design, and test project in which a dummy chest structure was developed. The chest consisted of mechanical elements that had been characterized by computer simulations as giving responses to blunt frontal impacts necessary for biofidelity. An analysis of mechanical rib structures indicated that materials having a high ratio of yield stress to modulus of elasticity were required. Only metals having unusually high yield strengths, such as spring steels, qualified. A mechanical system was developed with steel ribs pivoted at each end as a primary spring. A secondary spring was a pair of commercially available die springs acting in parallel with the ribs after 25.4 mm (1.00 in) deflection. A fluid damper was developed to provide the damping. The chest structure was tested under conditions modified from those used by Kroell. The modifications were holding the spine rigidly and reducing the impact masses.

The use of relatively small catalytic converters containing alumina-supported platinum (Pt) and palladium (Pd) catalysts to control exhaust emissions of hydrocarbons (HC) and carbon monoxide (CO) was investigated in full-scale vehicle tests. Catalytic converters containing 70-80in3 of fresh catalyst were installed at two converter locations on the vehicle. Carburetion was richer than stoichiometric, with air-fuel ratios (A/F) comparable to those proposed for dual-catalyst systems containing an NOx reduction catalyst. The vehicle was equipped with exhaust manifold air injection. Homogeneous thermal reaction in the exhaust manifolds played a significant role in the overall control of HC and CO. Four Pt catalysts, three Pd catalysts, and one Pt-Pd catalyst were prepared and evaluated. Total metal loadings were varied 0.01-0.07 troy oz. Hydrocarbon conversion efficiencies varied 62-82%, measured over the 1975 cold-hot start weighted Federal Test Procedure.

An analysis of oil pumpability reveals that engine oil pumping failures may occur because either the oil cannot flow under its own head to the oil screen inlet, or the oil is too viscous to flow through the screen and inlet tube fast enough to satisfy pump demands. To determine which factor is controlling, the behavior of commercial, multigraded oils was observed visually at temperatures from -40 to 0°F (-40 to - 17.8°C) in a laboratory oil pumpability test apparatus. Test results revealed that pumping failures occur by the first alternative: a hole is formed in the oil, and the surrounding oil is unable to flow into the hole fast enough to satisfy the pump. Of 14 oils tested, 7 failed to be pumped because of air binding or cavitation which developed in this manner. A model, which explains these failures in terms of yield point considerations and the low shear apparent viscosity of the oils, is proposed.

Development of engine-vehicle prototypes for low emissions and optimum fuel control characteristics has been facilitated through use of a computerized emissions test system. Simultaneous on-line sampling of exhaust species concentrations, fuel consumption, spark advance, pressures, and temperatures provides both graphical and computed outputs of several vehicle parameters that are important to development programs. On-line display of vehicle air-fuel ratio is continuously supplied. Either of two federal driving cycles (or any random driving schedule) may be employed. Dynamic calibration, range sensing, and zero-drift correction keep operator interaction and errors to a minimum. Capability for reprocessing, plotting, and/or patching stored data provides increased computational flexibility.

The incentive for use of an interstage diffuser in a free-shaft gas turbine engine is briefly examined and some pertinent published background data reviewed. Tests of two annular diffusers behind an upstream turbine show the deleterious effects of turbine exit flow nonuniformity on diffuser behavior. The flow acceleration provided by the area contraction of a power turbine nozzle located at the diffuser exit substantially improves the nature of the flow previously found to exist at the diffuser exit in the absence of the nozzle.

The use of multigrade (V.I. improved) oils in automotive engines has increased significantly in recent years. However, the performance of these oils in terms of factors such as oil economy, wear, and noise, is not always equal to that of single grade oils. Although the initial viscosity of multigrade oils is related to both the base oil and the V.I. improver, the viscosity decreases with use, with the primary factors determining the magnitude of the change being the degree of shear and the characteristics and concentration of the V.I. improver used. This decrease in viscosity has been assumed to be the cause of the decreases in oil economy that may occur with oil use. However, viscosity changes are not believed to be the primary factor responsible since similar oil economy changes have also been observed for single grade oils. Nevertheless, the characteristics and concentration of the V.I. improver used can be a significant factor influencing oil economy.

Various laboratory methods for measuring chip resistance were compared and found to rate different finishes in different orders. A field survey showed that a gravelometer using gravel rather than other media correlated well with actual service results. The necessity of preparing chip resistance test panels which very closely duplicate the actual finish obtained on cars was shown. The nature of chipping has been studied and improved rating systems developed. Detailed drawings, test procedures, and rating systems for the SAE gravelometer have been proposed for publication.

The combustion system developed for the General Motors GT-309 regenerative gas turbine is used to illustrate pertinent structural, performance, and exhaust emission considerations when designing for a vehicular gas turbine application. The development of each major component and the performance of the combustion system as a whole are reviewed. The satisfactory performance and durability potential of the GT-309 engine combustion system have been demonstrated by extensive operation in a component test facility and in several test cell and vehicle installed engines. Exhaust emissions of unburned hydrocarbons and carbon monoxide are minimal and are of no concern from an air pollution standpoint. No objectionable exhaust smoking and odor are produced.

Utilization of numerically controlled milling has been found particularly attractive in producing, in limited quantities, the three-dimensional curved surfaces characteristic of turbomachinery. In experimental and developmental programs its use can result in decreased fabrication cost, reduced lead time, and improved dimensional accuracy. Following a review of the general classifications of numerically controlled milling machines available for manufacture of such parts, illustrations are given of some of the procedures and techniques employed in their use. A variety of parts made using numerical control serve as examples.

Tests were conducted using older model cars with automatic transmissions to determine the effect of fluid composition on leakage past the rotating shaft seals. It was found that seal leakage was reduced or stopped by changing to seal-swelling fluids, and increased with seal-shrinking fluids. Leakage was also reduced by adding aromatic additives to existing fluids in the transmissions. Seal volume and hardness change results from bench tests support the car data.

The Total Immersion Test (ASTM D 471) for seal elastomers, used in evaluating the compatibility of fluids and seals for automatic transmissions, does not, produce hardness and volume change results similar to those found for rotating shaft seals in service. The Tip Cycle Test was devised to provide better agreement with service results. In the test, one side of the seal is exposed to air, and the other alternately to fluid and to air-fluid vapor. Rotating shaft seals were evaluated in both car and dynamometer transmission tests, and in various bench tests. Agreement was poor between transmission tests and both the Total Immersion and the Dip Cycle Tests. Good agreement was found with the Tip Cycle Test.

Effective performance of functional automotive components requires fluid sealing under compatible conditions. One method of determining this compatibility is through the use of immersion testing under a variety of conditions that simulate those experienced in actual use. By measuring the changes in the physical properties of the seal materials after immersion a judgment can be made regarding seal/fluid compatibility which will be encountered later in actual use. A series of immersion tests using representative seal materials and automotive fluids; namely, gear oils, transmission fluids, and motor oils were conducted within the framework of the Technical Committee on Automotive Rubber, jointly sponsored by SAE-ASTM.

The tedious, time consuming task of hand reducing data from the California exhaust emission test has been alleviated through the use of digital data acquisition equipment and a digital computer. Analog signals from exhaust gas analyzers and an engine speed transducer are converted to digital measurements which are recorded on tape and submitted to a digital computer for data analysis and computation of results. In the data analysis, the computer identifies the required driving modes from engine speed changes, taking into account the sample delay time. “Reported” composite emissions determined by the automatic data reduction method agree within 5% with results determined by careful hand analysis of analog strip chart recordings. The results determined by the automatic data reduction system are more consistent and accurate because human errors prevalent in hand analysis have been eliminated, and because nonlinear analyzer response is accounted for.

Conventional radial lip oil seals can be made more effective by utilizing helical grooving beneath the contact lip surface. Miniature hydrodynamic pumps so formed aid the radial lip seal in containing the oil by generating fluid forces opposite in direction to the leakage flow forces. This seal-shaft combination has been termed the Hydroseal. Four factorial experiments were conducted to evaluate the effect of helix angle, groove depth, groove width, and number of grooves on sealing performance. The criterion used as a basis for selecting the optimum design were leakage, wear, hardening of the sealing surface, and pumping capacity. These data indicated that the best hydroseal design was one with three grooves, 0.0003 in. deep, 0.014 in. wide, having a helix angle of 45 deg.