Search Results

In the United States, most school buses are powered by diesel engines. Some have advocated replacing diesel school buses with natural gas school buses, but little research has been conducted to understand the emissions from school bus engines. This work provides a detailed characterization of exhaust emissions from school buses using a diesel engine meeting 1998 emission standards, a low emitting diesel engine with an advanced engine calibration and a catalyzed particulate filter, and a natural gas engine without catalyst. All three bus configurations were tested over the same cycle, test weight, and road load settings. Twenty-one of the 41 “toxic air contaminants” (TACs) listed by the California Air Resources Board (CARB) as being present in diesel exhaust were not found in the exhaust of any of the three bus configurations, even though special sampling provisions were utilized to detect low levels of TACs.

The emission performance of a 1997 Mercedes OM 366 LA medium heavy-duty diesel engine and a 1998 Detroit Diesel Corporation (DDC) Series 60 heavy heavy-duty diesel engine was investigated using the US EPA hot-start transient cycle using different candidate diesel fuels developed by the Empresa Nacional Del Petroleo (ENAP), the state-owned oil production and refining company of Chile. The aim of the work was to identify a clean diesel fuel that can be readily produced and reduces emissions from diesel engines in Chile, particularly in Santiago Metropolitan Area where air pollution is a serious problem. Using a Mercedes engine of the type found in Chile, several candidate fuel formulations were tested in both the Mercedes and DDC engines to identify leading candidate formulations that would effectively reduce emission in both traditional and modern technology engines.

The use of a partial flow sampling system (PFSS) to measure nonroad steady-state diesel engine particulate matter (PM) emissions is a technique for certification approved by a number of regulatory agencies around the world including the US EPA. Recently, there have been proposals to change future nonroad tests to include testing over a nonroad transient cycle. PFSS units that can quantify PM over the transient cycle have also been discussed. The full flow constant volume sampling (CVS) technique has been the standard method for collecting PM under transient engine operation. It is expensive and requires large facilities as compared to a typical PFSS. Despite the need for a cheaper alternative to the CVS, there has been a concern regarding how well the PM measured using a PFSS compared to that measured by the CVS. In this study, three PFSS units, including AVL SPC, Horiba MDLT, and Sierra BG-2 were investigated in parallel with a full flow CVS.

The United States Environmental Protection Agency (EPA) has initiated Phase I of a regulatory program to control exhaust emissions of nonroad diesel engines over 37 kW. Central to any emissions regulation is the test procedure, which must include an appropriate test cycle. Based on actual in-use speed and estimated torque data collected from an agricultural tractor, a backhoe-loader, and a crawler tractor, three duty cycles were developed. Using an iterative process, comparison of chi-square statistical data was used to identify representative microtrips, segments of engine operation gathered during performance of selected activities. Representative microtrips for specific activities for a particular nonroad application were “strung” together to make up a test cycle. Before accepting the test cycle, data for the cycle was compared to statistical data used to characterize the raw data in an effort to validate that the cycle was representative of the raw data.

This paper describes experiments conducted to determine Federal Test Procedure (FTP) exhaust emissions, ozone-forming potentials, specific reactivities, and reactivity adjustment factors for several butane/propane alternative fuel blends run on a light-duty EHC-equipped gasoline vehicle converted to operate on liquefied petroleum gas (LPG). Duplicate emission tests were conducted on the light-duty vehicle at each test condition using appropriate EPA FTP test protocol. Hydrocarbon speciation was utilized to determine reactivity-adjusted non-methane organic gas (NMOG) emissions for one test on each fuel.

Over twenty prototype hybrid buses and other commercial vehicles are currently being completed and deployed. These vehicles are primarily “series” hybrid vehicles which use electric motors for primary traction while internal combustion engines, or high-speed turbine engines connected to generators, supply some portion of the electric propulsion and battery recharge energy. Hybrid-electric vehicles have an electric energy storage system on board that influences the operation of the heat engine. The storage system design and level affect the vehicle emissions, electricity consumption, and fuel economy. Existing heavy-duty emissions test procedures require that the engine be tested over a transient cycle before it can be used in vehicles (over 26,000 lbs GVW). This paper describes current test procedures for assessing engine and vehicle emissions, and proposes techniques for evaluating engines used with hybrid-electric vehicle propulsion systems.

This paper describes experiments conducted to determine the regulated emissions, ozone-forming potentials, specific reactivities, and reactivity adjustment factors for eight butane and propane alternative fuel blends run on a light-duty vehicle, emission certified to be a California transitional low emission vehicle (TLEV) and converted to operate on liquefied petroleum gas (LPG). Duplicate EPA FTP emission tests were conducted with each fuel. Hydrocarbon speciation was utilized to determine reactivity-adjusted non-methane organic gases (NMOG) emissions for one test on each fuel. Results showed that all eight fuels could allow the converted vehicle to pass California ultra-low emission vehicle (ULEV) NMOG and oxides of nitrogen (NOx) standards. Six of the eight fuels could allow the vehicle to pass ULEV carbon monoxide (CO) standards. BUTANE has been an important gasoline blending component for many years.

A Coordinating Research Council sponsored test program was conducted to determine the effects of diesel fuel properties on emissions from two heavy-duty diesel engines designed to meet EPA emission requirements for 1994. Results for a prototype 1994 DDC Series 60 were reported in SAE Paper 941020. This paper reports the results from a prototype 1994 Navistar DTA-466 engine equipped with an exhaust catalyst. A set of ten fuels having specific variations in cetane number, aromatics, and oxygen were used to study effects of these fuel properties on emissions. Using glycol diether compounds as an oxygenated additive, selected diesel fuels were treated to obtain 2 and 4 mass percent oxygen. Cetane number was increased for selected fuels using a cetane improver. Emissions were measured during transient FTP operation of the Navistar engine tuned for a nominal 5 g/hp-hr NOx, then repeated using a 4 g/hp-hr NOx calibration.

As stringent emission regulations further constrain engine manufacturers by tightening both NOx and particulate emission limits, a knowledge of fuel effects becomes more important than ever. Among the fuel properties that affect heavy-duty diesel engine emissions, cetane number can be very important. Part of the CRC-APRAC VE-10 Project was developed to quantify the effects of cetane number on NOx and other emissions from a prototype 1998 Detroit Diesel Series 60. Three fuels with different natural cetane number (41, 45, 52) were treated with several levels and types of cetane improvers to study a range of cetane number from 40 to 60. Statistical analysis was used to define how regulated emissions from this prototype 1998 engine decreased with chemically-induced cetane number increase. Variation of HC, CO, NOx, and PM were modeled using a combination of a fuel's naturally-occurring cetane number and its total cetane number obtained with cetane improver.

This paper describes experiments to determine the effect on exhaust emissions of starting on compressed natural gas (CNG) and then switching to gasoline once the catalyst reaches operating temperature. Carbon monoxide, oxides of nitrogen, and detailed exhaust hydrocarbon speciation data were obtained for dedicated CNG, then unleaded gasoline, and finally CNG start -gasoline run using the Federal Test Procedure at 24°C and at -7°C. The result was a reduction in emissions from the gasoline baseline, especially at -7°C. It was estimated that CNG start - gasoline run resulted in a 71 percent reduction in potential ozone formation per mile.

Concern over emissions from heavy-duty diesel engines at high altitudes prompted an investigation into the effects of increasing altitude on gaseous and particulate emissions. On behalf of the Engine Manufacturers Association, emissions from a Detroit Diesel Corporation Series 60 at local test conditions (barometer 98.9 kPa), and two simulated altitudes, Denver (82.6 kPa) and Mexico City (77.9 kPa) were examined using a special altitude simulation CVS. Transient torque output and full load steady-state torque, for this turbocharged aftercooled engine, decreased slightly with increasing altitude. Although, the DDC Series 60 compensates for variation in barometer, transient composite emissions of HC, CO, CO2, smoke, and particulate matter generally increased with increasing altitude for both transient and steady-state operation.

Several studies have investigated the effects of diesel fuel properties on heavy-duty engine emissions. The objective of this CRC-sponsored test program was to determine the effects of oxygenated diesel fuel, and to further investigate the effects of cetane number and aromatic content on emissions from a heavy-duty engine set to obtain transient NOx emissions below 5 and then 4 g/hp-hr. A fuel set was developed with controlled variations in cetane number, aromatics, and oxygen to superette their effects on emissions. Ignition improver was used to increase cetane number of several fuels. Oxygenated diesel fuel was achieved by adding a “glyme” compound to selected fuels to obtain 2 and 4 mass percent oxygen concentrations. With these fuels, emissions were measured over the EPA transient FTP using a prototype 1994 DDC Series 60 tuned for 5 and then 4 g/hp-hr NOx. No exhaust aftertreatment device was used on this engine.

The use of compressed natural gas as an alternative to conventional fuels has received a great deal of attention as a strategy for reducing air pollution from motor vehicles. In many cases, regulatory action has been taken to displace diesel fuel with natural gas in truck and bus applications. Emissions results of heavy-duty transient FTP testing of two Cummins L10-240G natural gas engines are presented. Regulated emissions of non-methane hydrocarbons, total hydrocarbons, CO, NOx, and particulate were characterized, along with emissions of formaldehyde. The effects of air/fuel ratio adjustments on these emissions were explored, as well as the effectiveness of catalytic aftertreatment in reducing exhaust emissions. Compared to typical heavy-duty diesel engine emissions, CNG-fueled engines using exhaust aftertreatment have great potential for meeting future exhaust emission standards, although in-use durability is unproven.

Two additive blends proposed for improving the flame luminosity in neat methanol fuel were investigated to determine the effect of these additives on the exhaust emissions in a dual-fueled Volkswagen Jetta. The two blends contained 4 percent toluene plus 2 percent indan in methanol and 5 percent cyclopentene plus 5 percent indan in methanol. Each blend was tested for regulated and unregulated emissions as well as a speciation of the exhaust hydrocarbons resulting from use of each fuel. The vehicle exhaust emissions from these two fuel blends were compared to the Coordinating Research Council Auto-Oil national average gasoline (RF-A), M100, and M85 blended from RF-A. Carter Maximum Incremental Reactivity Factors were applied to the speciated hydrocarbon emission results to determine the potential ozone formation for each fuel. Toxic emissions as defined in the 1990 Clean Air Act were also compared for each fuel.

Neat methanol fuel (M100) has many advantages for achieving low emission levels as an automotive fuel, but there are several items that require attention before this fuel can replace conventional fuels. One item involves the low flame luminosity of methanol. An extensive literature search and laboratory evaluation were conducted to identify potential additive candidates to improve the luminosity of a methanol flame. Potential compounds were screened based on their concentration, luminosity improvement, and duration of luminosity improvement during the burn. Three compounds were found to increase the flame luminosity for segments of the burn at relatively low concentrations: toluene, cyclopentene, and indan. In combination, these three compounds markedly improved the luminosity of methanol throughout the majority of the burn. The two combinations were 1) 4 percent toluene plus 2 percent indan and 2) 5 percent cyclopentene plus 5 percent indan in methanol.

A 1991 Toyota Camry equipped with an electrically-heated catalyst (EHC) system was evaluated in duplicate over the Federal Test Procedure (FTP) with three different fuels. Evaluations were conducted with the EHC in place but without any external heating, and with the EHC operated with a post-crank heating strategy. The EHC system was placed immediately upstream of an original production catalyst, which was then moved to a location 40.6 cm from the exhaust manifold. The three test fuels were: 1) the Auto/Oil industry average gasoline, RF-A; 2) a fuel meeting California's Phase II gasoline specifications; and 3) a paraffinic test fuel. Non-methane organic gas (NMOG) emission rates with the EHC active were similiar with all three fuels, with absolute levels less than or equal to California's 50,000 mile Ultra-Low Emission Vehicle (ULEV) standard. Substantial differences, however were observed in the ozone forming potential of these fuels with the EHC active.

Emissions from existing diesel-powered urban buses are increasingly scrutinized as local, state, and federal governments require enforcement of more stringent emission regulations and expectations. Currently, visual observation of high smoke levels from diesel-powered equipment is a popular indicator of potential emission problems requiring tune-up or engine maintenance. It is important that bus inspection and maintenance (I/M) operations have a quality control “test” to check engine emissions or diagnose the engine state-of-tune before or after maintenance. Ideally, the “emission test” would be correlated to EPA transient emissions standards, be of short duration, and be compatible with garage procedures and equipment. In support of developing a useful “short-test,” equipment was designed to collect samples of raw exhaust over a short time period for gaseous and particulate emissions.

This paper describes the findings of a laboratory effort to demonstrate improved automotive exhaust emission control with a cold-start hydrocarbon collection system. The emission control strategy developed in this study incorporated a zeolite molecular sieve in the exhaust system to collect cold-start hydrocarbons for subsequent release to an active catalytic converter. A prototype emission control system was designed and tested on a gasoline-fueled vehicle. Continuous raw exhaust emission measurements upstream and downstream of the zeolite molecular sieve revealed collection, storage, and release of cold-start hydrocarbons. Federal Test Procedure (FTP) emission results show a 35 percent reduction in hydrocarbons emitted during the cold-transient segment (Bag 1) due to adsorption by the zeolite.

The use of methanol as a “clean fuel” appears to be a viable approach to reduce air pollution. However, concern has been expressed about potentially high formaldehyde emissions from stoichiometrically operated light-duty vehicles. This paper presents results from an emission test program conducted for the California Air Resources Board (CARB) and the South Coast Air Quality Management District (SCAQMD) to identify and evaluate advanced catalyst technology to reduce formaldehyde emissions without compromising regulated emission control. An earlier paper presented the results of evaluating eighteen different catalyst systems on a hybrid methanol-fueled test vehicle. (1)* This paper discusses the optimization of three of these catalyst systems on four current technology methanol-fueled vehicles. Emission measurements were conducted for formaldehyde, nonmethane organic gases (NMOG), methanol, carbon monoxide, and oxides of nitrogen emissions.