Search Results

As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty automotive technologies in support of regulatory and compliance programs, a development project was started to study various test methods to benchmark Electric Drive Units (EDUs) consisting of an electric motor, inverter and a speed-reduction gearset. Several test methods were identified for consideration, including both in-vehicle testing of the complete EDU and stand-alone testing of the EDU and its subcomponents after removal from the vehicle. In all test methods explored, sweeps of speed and torque test points were conducted while collecting key EDU data required to determine efficiency, including motor torque and speed, direct current (DC) battery voltage and current into the inverter, and three-phase alternating current (AC) phase voltages and currents out of the inverter and into the electric motor.

Aftertreatment durability demonstration is a required validation exercise for on-road medium and heavy-duty diesel engine certification. The demonstration is meant to validate emissions compliance for the engine and aftertreatment system at full useful life or FUL. Current certification practices allow engine manufacturers to complete partial aging and then extrapolate emissions performance results to FUL. While this process reduces the amount of service accumulation time, it does not consider changes in the aftertreatment deterioration rate. Rather, deterioration is assumed to occur at a linear rate, which may lead to false conclusions relating to emissions compliance. With CARB and EPA’s commitment to the reduction of criteria emissions, emphasis has also been placed on revising the existing certification practices. The updated practices would require engine manufacturers to certify with an aftertreatment system aged to FUL.

The U.S. Environmental Protection Agency (EPA) certifies gasoline deposit control additives for intake valve deposit (IVD) control utilizing ASTM D5500, a vehicle test using a1985 BMW 318i. Concerns with the age of the test fleet, its relevance in the market today, and the availability of replacement parts led the American Chemistry Council’s (ACC) Fuel Additive Task Group (FATG) to begin a program to develop a replacement. General Motors suggested using a 2.4L LE9 test engine mounted on a dynamometer and committed to support the engine until 2030. Southwest Research Institute (SwRI®) was contracted to run the development program in four Phases. In Phase I, the engine test stand was configured, and a test fuel selected. In Phase II, a series of tests were run to identify a cycle that would build an acceptable level of deposits on un-additized fuel. In Phase III, the resultant test cycle was examined for repeatability.

SCR-on-filter, or SCRoF, is an emerging technology for different market segments and vehicle applications. The technology enables simultaneous particulate matter trapping and NOX reduction, and provides thermal management and aftertreatment packaging benefits. However, there is little information detailing the lubricant derived exposure effects on functional SCR performance. A study was conducted to evaluate the impact of various oil consumption pathways on a light duty DOC and SCRoF aftertreatment system. This aftertreatment system was aged utilizing an engine test bench modified to enable increased oil consumption rates via three unique oil consumption pathways. The components were characterized for functional SCR performance, ash morphology, and ash deposition characteristics. This included utilizing techniques, such as SEM / EDS, to evaluate the ash structures and quantify the ash elemental composition.

The California Air Resources Board (CARB)-funded Stage 3 Heavy-Duty Low NOX program focusses on evaluating different engine and after-treatment technologies to achieve 0.02g/bhp-hr of NOX emission over certification cycles. This paper highlights the controls architecture of the engine and after-treatment systems and discusses the effects of various strategies implemented and tested in an engine test cell over various heavy-duty drive cycles. A Cylinder De-Activation (CDA) system enabled engine was integrated with an advanced after-treatment controller and system package. Southwest Research Institute (SwRI) had implemented a model-based controller for the Selective Catalytic Reduction (SCR) system in the CARB Stage 1 Low-NOX program. The chemical kinetics for the model-based controller were further tuned and implemented in order to accurately represent the reactions for the catalysts used in this program.

Connected and automated driving technology is known to improve real-world vehicle efficiency by considering information about the vehicle’s environment such as traffic conditions, traffic lights or road grade. This study shows how the powertrain of a hybrid-electric vehicle realizes those efficiency benefits by developing methods to directly measure real-time transient power losses of the vehicle’s powertrain components through chassis-dynamometer testing. This study is a follow-on to SAE Technical Paper 2019-01-0116, Test Methodology to Quantify and Analyze Energy Consumption of Connected and Automated Vehicles [1], to understand the sources of efficiency gains resulting from connected and automated vehicle driving. A 2017 Toyota Prius Prime was instrumented to collect power measurements throughout its powertrain and driven over a specific driving schedule on a chassis dynamometer.

Dual injection fuel systems combine the knock and fuel economy benefits of gasoline direct injection (GDI) technology with the lower particulate emissions of port fuel injection (PFI) systems. For many years, this technology was limited to smaller-volume, high-end, vehicle models, but these technologies are now becoming main stream. The combination of two fuel injection systems has an impact on the combustion emission composition as well as the consistency of control strategy and emissions. Understanding the impact of these changes is essential for fuel and fuel additive companies, automotive companies, and aftertreatment developers. This paper describes the effects of dual injection technology on both regulated and non-regulated combustion emissions from a 2018 Toyota Camry during several cold-start, 4-bag United States Federal Test Procedure (FTP) cycle.

In recent years, gasoline direct injection (GDI) engines have been widely used by manufacturers in light-duty to meet stringent fuel economy and emissions standards. This study focuses on the relationship between various particle metrics such as number, size, surface area and mass of dilute exhaust particles from 12 different light-duty vehicles equipped with GDI engines. The campaign included the measurement of total particulate matter (PM) using Title 40 CFR Part 1066 compliant filter measurement, soot mass using photo-acoustics based analyzer, organic carbon (OC) & elemental carbon (EC) mass using thermo-optical analysis of quartz filter samples, solid particle number using European Union Regulation No. 49 compliant number system and solid particle size/number using an electrical mobility based size spectrometer.

SAE Recommended Practice J1540 [1] specifies test procedures to map transmission efficiency and parasitic losses in a manual transmission. The procedure comprises two parts. The first compares input and output torque over a range of speed to determine efficiency. The second measures parasitic losses at zero input torque over a range of speed. As specified in J1540, efficiency of transmissions is routinely measured on a test-stand under steady torque and speed [2] [3]. While such testing is useful to compare different transmissions, it is unclear whether the “in-use” efficiency of a given transmission is the same as that measured on the stand. A vehicular transmission is usually mated to a reciprocating combustion engine producing significant torque and speed fluctuations at the crankshaft. It is thus a valid question whether the efficiency under such pulsating conditions is the same as that under steady conditions.

Piston ring and liner wear measurements and analyses were performed in a production 3.6L V6 gasoline engine with radiolabelled engine parts. Three isotopes were generated: one in the engine liner using surface layer activation; one each in the top ring face and top ring side using bulk activation. Real-time wear measurements and subsequent rates of these three surfaces were captured using the radioactive decay of the isotopes into the engine oiling system. In addition, surface roughness and wear profile measurements were carried out using white light interferometry. The results from Phase I provided insights on evolution of wear and wear rates in critical engine components in a gasoline engine. Phase II will extend this work further and focus on evaluating the fuel additive effects on engine wear.

In June of 2015, the Environmental Protection Agency and the National Highway Traffic Safety Administration issued a Notice of Proposed Rulemaking to further reduce greenhouse gas emissions and improve the fuel efficiency of medium- and heavy-duty vehicles. The agencies proposed that vehicle manufacturers would certify vehicles to the standards by using the agencies’ Greenhouse Gas Emission Model (GEM). The agencies also proposed a steady-state engine test procedure for generating GEM inputs to represent the vehicle’s engine performance. In the proposal the agencies also requested comment on an alternative engine test procedure, the details of which were published in two separate 2015 SAE Technical Papers [1, 2]. As an alternative to the proposed steady-state engine test procedure, these papers presented a cycle-average test procedure.

The study described in this paper covers the development of the Sequence IVB low-temperature valvetrain wear test as a replacement test platform for the existing ASTM D6891 Sequence IVA for the new engine oil category, ILSAC GF-6. The Sequence IVB Test uses a Toyota engine with dual overhead camshafts, direct-acting mechanical lifter valvetrain system. The original intent for the new test was to be a direct replacement for the Sequence IVA. Due to inherent differences in valvetrain system design between the Sequence IVA and IVB engines, it was necessary to alter existing test conditions to ensure adequate wear was produced on the valvetrain components to allow discrimination among the different lubricant formulations. A variety of test conditions and wear parameters were evaluated in the test development. Radioactive tracer technique (RATT) was used to determine the wear response of the test platform to various test conditions.

In 2012, NHTSA and EPA extended Corporate Average Fuel Economy (CAFE) standards for light duty vehicles through the 2025 model year. The new standards require passenger cars to achieve an average of five percent annual improvement in fuel economy and light trucks to achieve three percent annual improvement. This regulatory requirement to improve fuel economy is driving research and development into fuel-saving technologies. A large portion of the current research is focused on incremental improvements in fuel economy through technologies such as new lubricant formulations. While these technologies typically yield less than two percent improvement, the gains are extremely significant and will play an increasing role in the overall effort to improve fuel economy. The ability to measure small, but statistically significant, changes in vehicle fuel economy is vital to the development of new technologies.

The Department of Transportation (DOT) National Highway Traffic Safety Administration (NHTSA) awarded a contract to Southwest Research Institute (SwRI) to conduct research and testing in the interest of motorcoach fire safety. The goal of this program was to develop and validate procedures and metrics to evaluate current and future detection, suppression, and exterior fire-hardening technologies that prevent or delay fire penetration into the passenger compartment of a motorcoach - in order to increase passenger evacuation time. The program was initiated with a literature review and characterization of the thermal environment of motorcoach fires and survey of engine compartments, firewalls, and wheel wells of motorcoaches currently in North American service. These characterizations assisted in the development of test methods and identification of the metrics for analysis. Test fixtures were designed and fabricated to simulate a representative engine compartment and wheel well.

Road tests of class 8 tractor trailers were conducted by the US Environmental Protection Agency (EPA) on a new and retreaded tires of varying rolling resistance in order to provide estimates of the quantitative relation between rolling resistance and fuel consumption. Reductions in fuel consumption were measured using the SAE J1231 (reaffirmation of 1986) test method. Vehicle rolling resistance was calculated as a load-weighted average of the rolling resistance (as measured by ISO28580) of the tires in each axle position. Both new and retreaded tires were tested in different combinations to obtain a range of vehicle coefficient of rolling resistance from a baseline of 7.7 kg/ton to 5.3 kg/ton. Reductions in fuel consumption displayed a strong linear relationship with coefficient of rolling resistance, with a maximum reduction of fuel consumption of 10 percent relative to the baseline.

A novel oxygenate, 5-methyl furoate ethyl ester (EF), was made by a chemical process from biomass and ethanol. This compound was then used as a renewable diesel additive at concentrations up to 10 percent by volume. This unique ester, which is similar in composition to a know food additive, was studied for engine performance in comparison with two other oxygenated alternatives (i.e. ethanol - EtOH and ethyl levulinate - EL) and with B20 (20 percent biodiesel). Tests were performed with a 2012 6.7 L Ford diesel engine using the heavy-duty Federal Test Procedure. The emission results indicated that a blend of the ester with diesel was comparable to the base fuel. In addition, the results also indicated that EF reduces the formation of particulate matter (PM) and carbon monoxide. Other properties of EF seem to improve the physical properties of the blended fuel such as lubricity and viscosity when compared to the base fuel.

Selective catalytic reduction (SCR) catalysts will be used to reduce oxides of nitrogen (NOx) emissions from internal combustion engines in a number of applications. Southwest Research Institute® (SwRI)® performed an Internal Research & Development project to study SCR catalyst thermal deactivation. The study included a V/W/TiO₂ formulation, a Cu-zeolite formulation and an Fe-zeolite formulation. This work describes NOx timed response to ammonia (NH₃) transients as a function of thermal aging time and temperature. It has been proposed that the response time of NOx emissions to NH₃ transients, effected by changes in diesel emissions fluid (DEF) injection rate, could be used as an on-board diagnostic (OBD) metric. The objective of this study was to evaluate the feasibility and practicality of this OBD approach.

Conventional diesel fuel has been in the market for decades and used successfully to run diesel engines of all sizes in many applications. In order to reduce emissions and to foster energy source diversity, new fuels such as alternative and renewable, as well as new fuel formulations have entered the market. These include biodiesel, gas-to-liquid, and alternative formulations by states such as California. Performance variations in fuel economy, emissions, and compatibility for these fuels have been evaluated and debated. In some cases contradictory views have surfaced. “Sustainable”, “Renewable”, and “Clean” designations have been interchanged. Adding to the confusion, results from one fuel in one type of engine such as an older heavy-duty engine, is at times compared to that of another fuel in another type such as a modern light-duty engine. This study was an attempt to compare the performance of several fuels in identical environments, using the same engine, for direct comparison.

Since the invention of the internal combustion engine, the contact between piston ring and cylinder liner has been a major concern for engine builders. The quality and durability of this contact has been linked to the life of the engine, its maintenance, and its exhaust gas and blowby emissions, but also to its factional properties and therefore fuel economy. While the basic design has not changed, many factors that affect the performance of the ring/liner contact have evolved and are still evolving. This paper provides an overview of observations related to the lubrication of the ring/liner contact.

The Lean NOx Trap (LNT) is a technology that could be used to reduce oxides of nitrogen from heavy-duty diesel engines to meet emissions standards (US 2010 and EURO 4/5/6). This paper describes a case-study for evaluating the feasibility of an LNT. LNTs suffer from sulfur poisoning and thermal aging limitations. Catalyst formulations allow reversal of sulfur poisoning through desulfation procedures. A case study was performed using a 7-liter diesel engine equipped with VGT, common rail fuel injection system, cooled EGR, oxidation catalyst and DPF. The LNT was positioned after the particulate filter. Gaseous raw emissions were measured from engine and various stages of aftertreatment. A Fourier Transform Infrared (FTIR) analyzer was used to characterize Ammonia and SO₂. Temperatures were measured in the substrate. Fast response NOx sensor allowed for continuous monitoring of the NOx in the LNT. A wide-range O₂ sensor was also utilized to measure equivalence ratio.