Refine Your Search

Search Results

Viewing 1 to 6 of 6
Journal Article

Gearshift Quality Sensitivity Analysis

2019-01-09
2019-26-0328
Gearshift quality is a perceived quality parameter. Hence, is getting much importance because of the increased awareness about comfortable and refined driving experience, especially in the case of passenger cars. When the topic of gearshift feeling is broached in manual transmission vehicles, synchronizer pack (shifter sleeve, engaging gear, strut, synchronizer and gear synchro ring assembly) have been the focus point for optimization. Synchronizer type (single, double or triple cone), lining material, datch chamfer angle of shifter sleeve/synchro ring of gear/synchronizer, all of these have been extensively studied in the past to improve the gearshift quality. With stringent timelines for vehicle development, OEMs prefer to use off-the-shelf powertrain systems developed by powertrain manufacturers. Due to this, avenues to refine gearshift feel gets reduced to a large extent and hence refinement becomes difficult.
Technical Paper

Evaluation of the Tire Wear Possibility due to Non-Steerable Twin Tire Lift Axle on Heavy Commercial Vehicle

2019-01-09
2019-26-0066
The commercial vehicle market in India is shifting to higher payload capacity vehicles due to a lower transportation cost per unit goods. To cater this requirement, the vehicle manufacturers are designing the heavy multi-axle commercial vehicles and with higher per axle loading capacity. One of such a vehicle design involves five-axle vehicle with non-steerable, twin tire, lift axle. Though using a twin tires have increased loading capacity of lift axle compared to a single tire self-steerable lift axle, it can cause tire scrub while vehicle is turning and leads to a significant tire wear. The tire wear possibility due to use of non-steerable lift axle is estimated through simulation using full vehicle model in ADAMS. The operating zone of the vehicle, where maximum tire wear can occur, is identified through simulation. Different alternatives to reduce tire wear for this scenario are also discussed.
Technical Paper

Full Vehicle NVH CAE Methodology Development to Address Tailgate Rattling on a Future Tata SUV

2019-01-09
2019-26-0213
In recent years, car manufacturers have been working intensively on new ways to improve the quality of interior trims. Elimination of squeak and rattle has become one of the main concerns for car manufacturers lately, given the significance of these incidences in customers' perception of overall quality. Traditionally, rattle problems are found and fixed with physical tests at the late design stage, mainly due to lack of up-front CAE simulation prediction methodology and tools availability. This article presents a finite element based methodology for the improvement of rattle performance of a vehicle tailgate. In this study, appropriate finite element (FE) modeling technique was introduced to accurately predict occurrence of tailgate rattle. Simulation process using commercial software “Nastran” employing modal and forced frequency response analyses was illustrated. Design modifications were incorporated for performance improvement of rattling on present and future SUVs.
Technical Paper

Simulating Bowden Cable Routing on Virtual Vehicle and Design Guidelines to Achieve the Best Cable Performance

2016-09-27
2016-01-8060
There has been immense focus on Gear Shift Quality as it is seen as an important factor for subjective evaluation of driving comfort of a vehicle with manual transmission. Synchronizer and driveline stiffness optimization is often the only area of focus for gear shift quality during early design stage. Proven Simulation models are already available for predicting the effect of synchronizer and driveline stiffness. Though Gear shift cable also has a significant effect on gear shift quality, neither design guidelines nor simulation models are available for predicting gear shift cable performance. Designers have relied on physical approach to establish cable routing, since cable routing cannot be predicted on virtual vehicle. In design phase cable routing is imagined and modeled in CAD using constrained curve geometry and later on established by physical trials on vehicle with various cable lengths, routing paths and clamp positions.
Technical Paper

Investigation of Frequent Pinion Seal and Hub Seal Leakages on Heavy Commercial Vehicles

2010-10-05
2010-01-2015
The automotive sector is going through a phase of stiff competition among various Original Equipment Manufacturers for increasing their profitability while ensuring highest levels of customer satisfaction. The biggest challenge for such companies lies in minimizing their overall cost involving investments in Research and Development, manufacturing, after sales service and warranty costs. Higher warranty costs not only affect the net profit but in turn it also affects the brand image of the company to a large extent in the long run. An effort is made here to target such warranty costs due to frequent tail pinion and hub seal leakages on single reduction/hub reduction axles of Heavy Commercial Vehicles in the field. A preliminary study involving the severity analysis of such failures is followed by a step by step investigation of these failures.
Technical Paper

Development of IT Enabled System for Data Management to Meet EU Vehicle Recyclability Directives

2010-04-12
2010-01-0276
EU directive 2005/64/EC on type approval of motor vehicles with respect to their Reusability, Recyclability and Recoverability ( RRR ) requires vehicle manufacturers to put in place the necessary arrangements and procedures for Parts, Materials and Weight (PMW ) data collection from full chain of supply. This is required to perform the calculations of recyclability rate and recoverability rate in line with ISO 22628. Commonly practiced data collection methodologies included spreadsheet and use of internationally available IT support system for collection of material data. Data complexity and prohibitive cost for using Internationally available IT Support systems like IMDS (International Material Data System) has led to the in-house development of IT enabled Solution customizing Siemens PLM software product (Team centre Enterprise) and SAP (SRM suite).
X