Search Results

The noise tests of electric motor systems serve as the foundation for studying their acoustic issues. However, there is currently a lack of corresponding method for identifying key noise characteristics, such as the noise frequency range that needs to be considered, the significant noise order, and the resonance band worth paying attention to, based on experimental test data under actual operating conditions. This article proposes a method for identifying the noise characteristics of an electric motor system based on tests conducted under distinct operating conditions, which consists of three parts: identifying the primary frequency range, the significant order, and the important resonance band. Firstly, in order to extract noise with the primary energy, the concept of noise contribution is introduced. The primary frequency range and the significant order under a specific operating condition can be obtained after extraction.

Alternating current (AC) heating is an efficient and homogeneous manner to warm Lithium-ion batteries (LIBs) up. The integrated design of AC heating combined with the motor drive circuit has been studied by many scholars. However, the problems of excessive heating frequency (>1kHz) and zeros torque output of the motor during the heating process have not been solved. High-frequency AC excitation may be detrimental to the battery because the effect of high-frequency AC excitation on the state of health of the battery is unknown. In addition, although the zero-torque output can be realized by controlling the q-axis current to zero, the torque ripple is still difficult to eliminate in a real-world application. To further solve the above problems, the motor’s neutral conductor is pulled out and connected to a large capacitor to increase the current amplitude of the AC heating at low frequencies.

High altitudes have a significant effect on the real driving emissions (RDE) of vehicles due to lower pressure and insufficient oxygen concentration. In addition, type approval tests for light-duty vehicles are usually conducted at altitudes below 1000 m. In order to investigate the influence of high altitude on vehicles fuel economy and emissions, RDE tests procedure had been introduced in the China VI emission regulations. In this study, the effect of altitude on fuel economy and real road emissions of three light-duty gasoline vehicles was investigated. The results indicated that for vehicles fuel economy, fuel consumption (L/100 km) for the tested vehicles decreased while the mean exhaust temperature increased with an increase in altitudes. Compared to near sea level, the fuel consumption (L/100 km) of the tested vehicle was reduced by up to 23.28%.

The application of Li(Ni0.8Co0.1Mn0.1)O2 (NCM811) cathode-based lithium-ion batteries (LIBs) has alleviated electric vehicle range anxiety. However, the subsequent thermal safety issues limit their market acceptance. A detailed analysis of the failure evolution process for large-format LIBs is necessary to address the thermal safety issue. In this study, prismatic cells with nominal capacities of 144Ah and 125Ah are used to investigate the thermal runaway (TR) characteristics triggered by lateral overheating. Additionally, TR characteristics under two states of charge (SoCs) (100% and 5%) are discussed. Two cells with 100% SoC exhibit similar characteristics, including high failure temperature, high inhomogeneity of temperature distribution, multi-points jet fire, and significant mass loss. Two cells with 5% SoC demonstrate only a slight rupture of the safety valve and the emission of white smoke.

The separation and analysis of the torque of the permanent magnet synchronous motor is of great significance for optimizing the torque output of the motor. Based on the frozen permeability method, the virtual work principle (VWP) or the Maxwell stress tensor method (MSTM) is often used to separate the torque for torque analysis. However, considering the influence of non-ideal factors such as motor saturation, cross-coupling and flux harmonics, there are differences in torque separation between the VWP and the MSTM, which has been researched and analyzed in this paper. Based on this, for the assisted airspace barrier design of a surface-inserted permanent magnet synchronous motor, to conduct theoretical research on the torque optimization design, this paper uses the VWP to separate the average torque and the MSTM to separate the torque ripple.

An accurate finite element (FE) model is the basis for the numerical prediction of vibration and noise of permanent magnet synchronous motors (PMSMs). This paper provides an equivalent modeling method of PMSMs considering the orthotropic material parameters of the stator system. First, a theoretical analysis of the influence of orthotropic material parameters on modal characteristics is implemented. Subsequently, the influence of orthotropic material parameters on the modal frequency of the stator is analyzed through the FE method. Then, the modal parameters of the stator core and the stator assembly are obtained by modal tests. According to the equivalent FE model and modal parameters, the orthotropic material parameters of the stator system are acquired. Moreover, to save the calculation time and simplify the modal identification process, the influence of windings is taken into account through additional mass and additional stiffness during the modeling process.

In this work, the influences of various real-timely available energy management strategies on vehicle fuel consumption (VFC) and energy flow of a range-extender electric vehicle were studied The strategies include single-point, multi-point, speed-following, and equivalent consumption minimization strategy. In addition, the dynamic programming method which cannot be used in real time, but can provide the optimal solution for a known drive situation was used for comparison. VFCs and energy flow characteristics with different strategies under Worldwide Harmonized Light Vehicles Test Cycle (WLTC) were obtained through computer modeling, and the results were verified experimentally on a range-extender test bench. The experimental results are consistent with the modeled ones in general with a maximum deviation of 4.11%, which verifies the accuracy of the simulation models.

The accelerated global progress in the research and development of automobile products, and the use of new technologies, such as the Internet, cloud computing and big data, to coordinate development platforms in different regions and fields, can reduce the duration and cost of development and testing. Specifically, in the context of the current coronavirus disease (COVID-19) pandemic, which has caused great obstacles to normal logistics and transportation, personnel exchanges and information communication, platforms that can support global operation are significant for product testing and validation, because they eliminate the need for the transportation of personnel and equipment. Therefore, the establishment of a distributed test and validation platform for automotive powertrain systems, which can integrate software and hardware testing, is important in terms of both scientific research and industrialization.

For electric vehicles, electromagnetically excited noise from the traction motor is one of the main acoustic noise sources, especially for automobiles driven at low speed that mechanical noise and aerodynamic noise are minor. To analyze the characteristics of the electromagnetically excited noise and propose noise reduction suggestions, an accurate noise prediction model is essential. In this paper, a multi-physics model to predict the electromagnetic force excited acoustic noise of induction motor is presented. First, a Three-Dimensional (3D) transient electromagnetic model of the motor was established using the Finite Element Method (FEM). By inputting the current signal collected in the noise test as the current source in the FEM model, the uneven distributed time-varying magnetic forces, which included the influence of the current harmonics due to Pulse-Width Modulation (PWM), was calculated. Then, a structural model was built.

The backlash between engaging components in a driveline is unavoidable, especially when the gear runs freely and collides with the backlash, the impact torque generated increases the vibration amplitude. The power-split hybrid electric vehicle generates output torque only from the traction motor during the launching process. The nonlinear backlash can greatly influence the driveability of the driveline due to the rapid response of the traction motor and the lack of the traditional clutches and torsional shock absorbers in the powertrain. This paper focuses on the launch vibration of the power-split hybrid electric vehicle, establishes a nonlinear driveline model considering gear backlash, including an engine, two motors, a Ravigneaux planetary gear set, a reducer, a differential, a backlash assembly, half shafts, and wheels.

In this paper, in order to avoid the frequent switching of engine operating points and improve the fuel economy during driving, this paper proposes a control strategy for the 4-wheel drive (4WD) hybrid vehicle based on wavelet transform. First of all, the system configuration and the original control strategy of the 4WD hybrid vehicle were introduced and analyzed, which summarized the shortcomings of this control strategy. Then, based on the analyze of the original control strategy, the wavelet transform was used to overcome its weaknesses. By taking advantage over the superiority of the wavelet transform method in multi signal disposition, the demand power of vehicle was decomposed into the stable drive power and the instantaneous response power, which were distributed to engine and electric motor respectively. This process was carried out under different driving modes.

A new range-extension hybrid powertrain concept, namely the Tongji Extended-range Hybrid Technology (TJEHT) was developed and demonstrated in this study. This hybrid system is composed of a direct-injection gasoline engine, a traction motor, an Integrated Starter-Generator (ISG) motor, and a transmission. In addition, an electronically controlled clutch between the ISG motor and engine, and an electronically controlled synchronizer between the ISG motor and transmission are also employed in the transmission case. Hence, this system can provide six basic operating modes including the single-motor driving, dual-motor driving, serial driving, parallel driving, engine-only driving and regeneration mode depending on the engagement status of the clutch and synchronizer. Importantly, the unique dual-motor operation mode can improve vehicle acceleration performance and the overall operating efficiency.

Recently, electro-hydraulic brake systems (EHB) has been developed to take place of the vacuum booster, having the advantage of faster pressure build-up and continuous pressure regulation. In contrast to the vacuum booster, the pressure estimation for EHB is worth to be studied due to its abundant resource (i.e. electric motor) and cost-effective benefit. This work improves an interconnected pressure estimation algorithm (IPEA) based on actuator characteristics by introducing the vehicle dynamics and validates it via vehicle tests. Considering the previous IPEA as the prior pressure estimation, the wheel speed feedback is used for modification via a proportional-integral (PI) observer. Superior to the IPEA based on actuator characteristics, the proposed PEA improves the accuracy by more than 20% under the mismatch of pressure-position relation.

The aftertreatment system is indispensable for the removal of the noxious pollutants emitted by diesel engines, whose efficiency depends largely on the exhaust gas temperature. Therefore, this study proposes a thermal management strategy including post injection, intake throttling and late post injection to improve the efficiency of the aftertreatment system for a heavy-duty diesel engine. In the experiments, the effects of main injection, post injection, injection pressure and throttle opening on the exhaust gas temperature at diesel oxidation catalyst (DOC) inlet were studied, with the influence of late post injection on the exhaust gas temperature at DOC outlet also investigated. The results showed that the reasonable control of throttle opening and post injection (such as the adjustment of injection timing and injection quantity) can significantly improve the average temperature at DOC inlet from 237.8°C to 333.6°C in the WHTC, with an increase of 40.3%.

Based on the vector space decomposition (VSD) transformation, the phase currents of the asymmetric dual three phase permanent magnet synchronous motor (ADT-PMSM) can be mapped into three orthogonal subspaces, i.e., α-β subspace, x-y subspace and O1-O2 subspace. The mechanical energy conversion takes place in the α-β subspace, while in the x-y and O1-O2 subspaces only losses are produced. With neutral points being isolated, O1-O2 subspace can be omitted. So the vector control algorithm can control the α-β and x-y subspaces separately to realize the four dimensional current control. In the α-β subspace, deviation decoupling control method is employed to realize the mechanical energy conversion, which is robust to the motor parameters.

Compared with the low-frequency ignition order of mechanical and combustion noise of an internal combustion engine, the noise of electric drive assembly of electric vehicles is mainly the high-frequency whining noise generated by electromagnetic forces of motors and gear meshing of reducers, as well as the high-frequency umbrella-shape noise generated by DC/AC pulse width modulation. Although the radiated sound power of these high frequency noise is far less than that of an internal combustion engine, the high frequency noise of the motor and the reducer is subjectively quite annoying. This paper studies the characteristics of electromagnetic noise of a permanent magnet synchronous motor in an electric car. By testing and analyzing of noise sources of an electric motor in the car and on a test rig, the spatial order characteristics and amplitude-frequency characteristics of the electromagnetic forces are revealed. The noise orders are multiples of the number of motor poles.

On the dual-motor electric vehicle, which is driven by two electric motors mounted on the front and rear axles respectively, longitudinal dynamic control and electro-dynamic braking can be achieved by controlling the torque of front and rear axle motors respectively. Suspension displacement is related to the wheel torque, thus the pitch of vehicle body can be influenced by changing the torque distribution ratio. The pitch of the body has a great influence on the vehicle comfort, which occurs mainly during acceleration and braking progress. Traditionally active suspension is adopted to control the pitch of body. Instead, in this paper an ideal torque distribution strategy is developed to limit the pitch during acceleration and braking progress. This paper first explores the relationship between the torque distribution and the body pitch through the real vehicle test, which reveals the feasibility of the vehicle comfort promotion by optimizing the torque distribution coefficient.

The power-split transmission is considered as one of the major technologies for hybrid electric vehicles. It utilizes two electric motors/generators (MGs) and a power-split device (planetary gear sets) to make the speed of internal combustion engine (ICE) independent from the vehicle speed, and in that way enables the ICE to operate in a high-efficiency region under all driving cycles. In this study, a compound power-split hybrid system integrated with a two-planetary gear train is proposed. To suppress the vehicle jerk intensity and improve the driving comfort during the transition from EV (Electric Vehicle) mode to HEV (Hybrid Electric Vehicle) mode, a torque coordinated control strategy is derived. Based on the analysis of mode transition in different sections, mathematical models of each section are deduced, respectively. Then a model-based torque coordinated control method is used to solve out the target output torques of ICE, MGs and brakes in each mode transition phase.

BBW (Brake-by-wire) can increase the vehicle safety performance due to high control accuracy and fast response speed. As one solution of BBW, the novel Integrated-electro-hydraulic brake system (I-EHB) is proposed, which consists of electro-hydraulic booster and hydraulic pressure control unit. The electro-hydraulic booster is activated by an electric motor that driving linear motion mechanism to directly produce the master cylinder pressure. With electro-hydraulic booster as an actuator, the hydraulic pressure control problem is a key issue. Most literatures deal with the pressure control issue based on the feedback pressure signal measured by pressure sensor. As far as the authors are aware, none of the proposed techniques takes into account the pressure sensor unequipped BBW. In this paper, there is no pressure feedback signal, but there is only position feedback signal measured by position sensor for control law design.

Steering of skid-steered vehicles without steering mechanism is realized by differential drive/brake torque generated from in-wheel motors at left and right sides. Compared to traditional Ackerman-steered vehicles, skid-steered vehicles consume much more energy while steering due to greater steering resistance. Torque allocation is critical to the distributed drive skid-steered vehicles, since it influences not only steering performance, but also energy efficiency. In this paper, the dynamic characteristics of six-wheeled skid-steered vehicles were analyzed, and a 2-DOF vehicle model was established, which is important for both motion tracking control and torque allocation. Furthermore, a hierarchical controller was proposed. Considering tire force characteristics and tire slip, the upper layer calculates the generalized force and desired yaw moment based on anti-windup PI (proportion-integral) control method.