Search Results

The United States Environmental Protection Agency’s (U.S. EPA’s) National Vehicle and Fuel Emissions Laboratory (NVFEL) has been developing new approaches for use in screening emissions from various types of new and in-use (used) engines to investigate if their exhaust emissions comply with federal emission standards. If the results from screening tests suggest anything unusual, EPA’s compliance program could investigate further to determine if that particular engine group or family should receive more rigorous compliance testing and analysis. In 2019, the EPA finished developing a means to screen the emissions of marine outboard engines, including the use of specialized equipment, laboratory methods, and procedures capable of controlling outboard marine engines to screen whether their exhaust is in line with appropriate emission standards.

In 2005, the United States Environmental Protection Agency (EPA) and Southwest Research Institute (SwRI) embarked on a mission to help the city of Beijing, China, clean its air. Working with the Beijing Environmental Protection Bureau (BEPB), the effort was a pilot diesel retrofit demonstration program involving three basic retrofit technologies to reduce particulate matter (PM). The three basic technologies were the diesel oxidation catalyst (DOC), the flowthrough diesel particulate filter (FT-DPF), and the wallflow diesel particulate filter (WF-DPF). The specific retrofit systems selected for the project were verified through the California Air Resources Board (CARB) or the EPA verification protocol [1]. These technologies are generally verified for PM reductions of 20-40 percent for DOCs, 40-50 percent for the FT-DPF, and 85 percent or more for the high efficiency WF-DPF.

The attractiveness of the hydraulic hybrid concept stems from the high power density and efficiency of the pump/motors and the accumulator. This is particularly advantageous in applications to heavy vehicles, as high mass translates into high rates of energy flows through the system. Using dry case hydraulic pumps further improves the energy conversion in the system, as they have 1-4% better efficiency than traditional wet-case pumps. However, evacuation of fluid from the case introduces air bubbles and it becomes imperative to address the deaeration problems. This research develops a bubble elimination efficiency testing apparatus (BEETA) to establish quantitative results characterizing bubble removal from hydraulic fluid in a cyclone deaeration device. The BEETA system mixes the oil and air according to predetermined ratio, passes the mixture through a cyclone deaeration device, and then measures the concentration of air in the exiting fluid.

Reducing aerodynamic drag and tire rolling resistance in trucks using cooled EGR engines meeting EPA 2004 emissions standards has been observed to result in increases in fuel economy and decreases in NOx emissions. We report here on tests conducted using vehicles equipped a non-EGR engine meeting EPA 2004 emission standards and an electronically-controlled engine meeting EPA 1998 emissions standards. The effects of trailer fairings and single-wide tires on fuel economy and NOx emissions were tested using SAE test procedure J1321. NOx emissions were measured using a portable emissions monitoring system (PEMS). Fuel consumption was estimated by a carbon balance on PEMS output and by the gravimetric method specified by test procedure J1321. Fuel consumption decreased and fuel economy increased by a maximum of about 10 percent, and NOx emissions decreased by a maximum of 20 percent relative to baseline.

We hypothesize that components designed to improve fuel economy by reducing power requirements should also result in a decrease in emissions of oxides of nitrogen (NOx). Fuel economy and NOx emissions of a pair of class 8 tractor-trailers were measured on a test track to evaluate the effects of single wide tires and trailer aerodynamic devices. Fuel economy was measured using a modified version of SAE test procedure J1321. NOx emissions were measured using a portable emissions monitoring system (PEMS). Fuel consumption was estimated by a carbon balance on PEMS output and correlated to fuel meter measurements. Tests were conducted using drive cycles simulating highway operations at 55 mph and 65 mph and suburban stop-and-go traffic. The tests showed a negative correlation (significant at p < 0.05) between fuel economy and NOx emissions. Single wide tires and trailer aerodynamic devices resulted in increased fuel economy and decreased NOx emissions relative to the baseline tests.

Due to its high efficiency and superior durability the diesel engine is again becoming a prime candidate for future light-duty vehicle applications within the United States. While in Europe the overall diesel share exceeds 40%, the current diesel share in the U.S. is 1%. Despite the current situation and the very stringent Tier 2 emission standards, efforts are being made to introduce the diesel engine back into the U.S. market. In order to succeed, these vehicles have to comply with emissions standards over a 120,000 miles distance while maintaining their excellent fuel economy. The availability of technologies such as high-pressure common-rail fuel systems, low sulfur diesel fuel, NOx adsorber catalysts (NAC), and diesel particle filters (DPFs) allow the development of powertrain systems that have the potential to comply with the light-duty Tier 2 emission requirements. In support of this, the U.S.

A 2001 General Motors 4.3 liter V-6 marine engine was baseline emissions tested and then equipped with catalysts. Emission reduction effects of exhaust gas recirculation (EGR) were also explored. Because of a U.S. Coast Guard requirement that inboard engine surface temperatures be kept below 200°F, the engine's exhaust system, including the catalysts, was water-cooled. Engine emissions were measured using the ISO-8178-E4 5-mode steady-state test for recreational marine engines. In baseline configuration, the engine produced 16.6 g HC+NOx/kW-hr, and 111 g CO/kW-hr. In closed-loop control with catalysts, HC+NOx emissions were reduced by 75 percent to 4.1 g/kW-hr, and CO emissions were reduced by 36 percent to 70 g/kW-hr of CO. The catalyzed engine was then installed in a Sea Ray 190 boat, and tested for water reversion on both fresh and salt water using National Marine Manufacturers Association procedures.

The use of a partial flow sampling system (PFSS) to measure nonroad steady-state diesel engine particulate matter (PM) emissions is a technique for certification approved by a number of regulatory agencies around the world including the US EPA. Recently, there have been proposals to change future nonroad tests to include testing over a nonroad transient cycle. PFSS units that can quantify PM over the transient cycle have also been discussed. The full flow constant volume sampling (CVS) technique has been the standard method for collecting PM under transient engine operation. It is expensive and requires large facilities as compared to a typical PFSS. Despite the need for a cheaper alternative to the CVS, there has been a concern regarding how well the PM measured using a PFSS compared to that measured by the CVS. In this study, three PFSS units, including AVL SPC, Horiba MDLT, and Sierra BG-2 were investigated in parallel with a full flow CVS.

The United States Environmental Protection Agency (EPA) has initiated Phase I of a regulatory program to control exhaust emissions of nonroad diesel engines over 37 kW. Central to any emissions regulation is the test procedure, which must include an appropriate test cycle. Based on actual in-use speed and estimated torque data collected from an agricultural tractor, a backhoe-loader, and a crawler tractor, three duty cycles were developed. Using an iterative process, comparison of chi-square statistical data was used to identify representative microtrips, segments of engine operation gathered during performance of selected activities. Representative microtrips for specific activities for a particular nonroad application were “strung” together to make up a test cycle. Before accepting the test cycle, data for the cycle was compared to statistical data used to characterize the raw data in an effort to validate that the cycle was representative of the raw data.

FTP-UDDS (urban dynamometer driving schedule) exhaust particulate matter (PM) emission rates were determined for 361 light-duty gasoline (LDGV) and 49 diesel passenger vehicles ranging in model year (MY) from 1965 to 1997. LDGVs were recruited into four MY categories. In addition, special effort was made to recruit LDGVs with visible smoke emissions, since these vehicles may be significant contributors to the mobile source PM emission inventory. Both light and heavy-duty diesels where included in the passenger diesel test fleet, which was insufficient in size to separate into the same MY categories as the LDGVs. Vehicles were tested as-received in three areas: Denver, Colorado; San Antonio, Texas; and the South Coast Air Quality Management District, California. The average PM emission rates were 3.3, 79.9, 384 and 558 mg/mi for 1991-97 MY LDGVs, pre-1981 LDGVs, smoking LDGVs and the diesel vehicles, respectively.

Six heavy-duty diesel engines were tested for exhaust emissions on the ISO 8-mode nonroad steady-state duty cycle and the U.S. FTP highway transient test cycle. Two of these engines were baseline nonroad engines, two were Tier 1 nonroad engines, and two were highway engines. One of the Tier 1 nonroad engines and both of the highway engines were also tested on three transient cycles developed for nonroad engines. In addition, published data were collected from an additional twenty diesel engines that were tested on the 8-mode as well as at least one transient test cycle. Data showed that HC and PM emissions from diesel engines are very sensitive to transient operation while NOx emissions are much less so. Although one of the nonroad transient duty cycles showed lower PM than the steady-state duty cycles, all four of the other cycles showed much higher PM emissions than the steady-state cycle.

This paper describes a method used to compare the emissions from transient operation of an engine with the emissions from steady state operating modes of the engine. Weightings were assigned to each mode based on the transient cycle under evaluation. The method of assigning the weightings for each mode took into account several factors, including the distance between each second of the transient cycle's speed-and-torque point requests (in a speed vs. torque coordinate system) and the given mode. Two transient cycles were chosen. The transient cycles were taken from actual in-use data collected on nonroad engines during in-field operation. The steady state modes selected were based on both International Standard Organization (ISO) test modes, as well as, augmentation based on contour plots of the emissions from nonroad diesel engines. Twenty-four (24) steady-state modes were used. The transient cycle's speed-and-torque points are used to weight each steady state mode in the method.

A second carbonyl round robin was conducted to enable participating laboratories doing routine analysis of carbonyls in vehicle exhaust emissions to assess their analytical capabilities. Three sets of solutions in acetonitrile containing varying number and amounts of standard DNPH-carbonyls were prepared. The parent carbonyls are known components of vehicle exhaust emissions. The samples were designed to challenge the capabilities of the participants to separate, identify and quantify all the components. The fourteen participating laboratories included automotive, contract, petroleum and regulatory organizations. All participants were able to separate and identify the C3 carbonyls; a few were not able to separate MEK from butyraldehyde and methacrolein from butyraldehyde; and many were not able to separate adequately the isomers of tolualdehyde. Inadequate separation and lack of appropriate standards resulted in a few misidentifications.

A modified constant volume sampling (CVS) system has been used to sample fugitive hydrocarbon (HC) emissions to determine whether such systems can help identify excess vehicular HC sources, such as leaking gas caps. The approach was successful in distinguishing tightly sealed, marginally leaking and grossly leaking caps. The technique may be useful in motor vehicle inspection and maintenance (I/M) facilities as a less intrusive alternative to techniques requiring pressurization of the fuel system.

Regulated emissions (THC, CO, NOx, and PM) and particulate SOF and sulfate fractions were determined for a 1995 Detroit Diesel Series 50 urban bus engine at varying fuel sulfur levels, with and without catalytic converters. When tested on EPA certification fuel without an oxidation catalyst this engine does not appear to meet the 1994 emissions standards for heavy duty trucks, when operating at high altitude. An ultra-low (5 ppm) sulfur diesel base stock with 23% aromatics and 42.4 cetane number was used to examine the effect of fuel sulfur. Sulfur was adjusted above the 5 ppm level to 50, 100, 200, 315 and 500 ppm using tert-butyl disulfide. Current EPA regulations limit the sulfur content to 500 ppm for on highway fuel. A low Pt diesel oxidation catalyst (DOC) was tested with all fuels and a high Pt diesel oxidation catalyst was tested with the 5 and 50 ppm sulfur fuels.

There are many sources of variability when sampling motor vehicle emissions, including intermittant losses to “wetted” sampling system surfaces if water condensation occurs and thermal decomposition if sampling system surfaces get excessively hot. The risk of losses varies during typical transient speed emissions tests and depends upon many variables such as temperature, pressure, exhaust dilution ratio, dilution air humidity, fuel composition, and emissions composition. Procedures are described for injection of known concentrations of compounds of interest into transient motor vehicle exhaust for the purpose of characterizing losses between the vehicle tailpipe and emissions analyzer.

Eleven experienced commercial automotive technicians were recruited and trained to repair IM240 emission failures using a specially developed 30 hour course. The training course emphasized the use of an oscilloscope and a flow chart and wave form strategy to repair vehicles. Each technicians' performance was evaluated based on the repair of three or four in-use Arizona IM240 failures. Pre-training and post-training written tests were also administered. Results from this limited study were encouraging. After the technician training, HC and CO emission levels were reduced by 69% and NOx by 58%. More importantly, most of the technicians learned some new and useful diagnostic and equipment skills which they can immediately apply to their businesses. They also became more motivated to tackle the challenge of repairing vehicles to low transient emissions, and aware of the existence and use of new sophisticated diagnostic tools such as oscilloscopes.

Due to continuing reductions in EPA's emission standard values for exhaust particulate emissions, industry production has shifted towards engines that produce very low amounts of particulate emissions. Thus, it is very possible that future engines will challenge the error range of the current instrumentation and procedures used to measure particulate emissions by being designed to produce extremely low levels of particulates. When low particulate emitting engines are sampled at low flowrates, the resulting filter loadings may violate the minimum filter loading recommendation in the Heavy Duty Federal Test Procedure [1]. Conversely, higher flow rates may be an inappropriate option for increasing filter loading due to the possibility of stripping volatile organic compounds from the particulate sample or otherwise artificially reducing the accumulated mass [2].

Six in-use vehicles were tested on a baseline gasoline and nine gasoline/ethanol blends to determine the effect of ethanol content in fuels on automotive exhaust emissions and fuel economy. The baseline gasoline was representative of average summer gasoline and served as the base from which the other fuels were blended. For the majority of the vehicles, total hydrocarbon, and carbon monoxide exhaust emissions as well as fuel economy decreased while NOx and acetaldehyde exhaust emissions increased as the ethanol content in the test fuel increased. Formaldehyde and carbon dioxide emissions were relatively unaffected by the addition of ethanol. The emission responses to the increased fuel oxygen levels were consistent with what would be expected from leaning-out the air/fuel ratio for a spark ignition engine. The results are shown graphically and a linear regression is performed utilizing the method of least squares to investigate statistically significant trends in the data.

The Schatz Heat Battery stores excess heat energy from the engine cooling system during vehicle operation. This excess energy may be returned to the coolant upon the ensuing cold start, shortening the engine warm-up period and decreasing cold start related emissions of unburned fuel and carbon monoxide (CO). A Heat Battery was evaluated on a test vehicle to determine its effect on unburned fuel emissions, CO emissions, and fuel economy over the cold start portion (Bag 1) of the Federal Test Procedure (FTP) at 24°C and -7°C ambient conditions. The Heat Battery was mounted in a vehicle fueled alternately with indolene clear (unleaded gasoline) and M85 high methanol blend fuels. Several Heat Battery/coolant flow configurations were evaluated to determine which would result in lowest cold start emissions.