Search Results

Quasicrystalline (QC) coatings were evaluated as leading-edge protection materials for rotor craft blades. The QC coatings were deposited using high velocity oxy-fuel thermal spray and predominantly Al-based compositions. Ice adhesion, interfacial toughness with ice, wettability, topography, and durability were assessed. QC-coated sand-blasted carbon steel exhibited better performance in terms of low surface roughness (Sa ~ 0.2 μm), liquid repellency (water contact angles: θadv ~85°, θrec ~23°), and better substrate adhesion compared to stainless steel substrates. To enhance coating performance, QC-coated sand-blasted carbon steel was further exposed to grinding and polishing, followed by measuring surface roughness, wettability, and ice adhesion strength. This reduced the surface roughness of the QC coating by 75%, resulting in lower ice adhesion strengths similar to previously reported values (~400 kPa).

The present paper aims at developing an innovative procedure to create a one-dimensional (1D) real-time capable simulation model for a heavy-duty diesel engine. The novelty of this approach is the use of the top-level engine configuration, test cell measurement data, and manufacturer maps as opposite to common practice of utilizing a detailed 1D engine model. The objective is to facilitate effective model adjustments and hence further increase the application of Hardware-in-the-Loop (HiL) simulations in powertrain development. This work describes the development of Fast Running Model (FRM) in GT-SUITE simulation software. The cylinder and gas-path modeling and calibration are described in detail. The results for engine performance and exhaust emissions produced satisfactory agreement with both steady-state and transient experimental data.

In order to meet emissions and power requirements, modern engine design has evolved in complexity and control. The cost and time restraints of calibration and testing of various control strategies have made virtual testing environments increasingly popular. Using Hardware-in-the-Loop (HiL), Volvo Penta has built a virtual test rig named VIRTEC for efficient engine testing, using a model simulating a fully instrumented engine. This paper presents an innovative Artificial Neural Network (ANN) based model for engine simulations in HiL environment. The engine model, herein called Artificial Neural Network Engine (ANN-E), was built for D8-600 hp Volvo Penta engine, and directly implemented in the VIRTEC system. ANN-E uses a combination of feedforward and recursive ANNs, processing 7 actuator signals from the engine management system (EMS) to provide 30 output signals.

Particulate matter emissions from gasoline direct injection engines are a concern due to the health effects associated with ultrafine particles. This experimental study investigated sources of particulate matter emissions variability observed in previous tests and also examined the effect of ethanol content in gasoline on particle number (PN) concentrations and particle mass (PM) emissions. FTIR measurements of gas phase hydrocarbon emissions provided evidence that changes in fuel composition were responsible for the variability. Exhaust emissions of toluene and ethanol correlated positively with emitted PN concentrations, while emissions of isobutylene correlated negatively. Exhaust emissions of toluene and isobutylene were interpreted as markers of gasoline aromatic content and gasoline volatility respectively.

Metallic open-cell foams have proven to be valuable for many engineering applications. Their success is mainly related to mechanical strength, low density, high specific surface, good thermal exchange, low flow resistance and sound absorption properties. The present work aims to investigate three principal aspects of real foams: the geometrical characterization, the flow regime characterization, the effects of the pore size and the porosity on the pressure drop. The first aspect is very important, since the geometrical properties depend on other parameters, such as porosity, cell/pore size and specific surface. A statistical evaluation of the cell size of a foam sample is necessary to define both its geometrical characteristics and the flow pattern at a given input velocity. To this purpose, a procedure which statistically computes the number of cells and pores with a given size has been implemented in order to obtain the diameter distribution.

Large-scale emergency or off-grid power generation is typically achieved through diesel or natural gas generators. To meet governmental emission requirements, emission control systems (ECS) are required. In operation, effective control over the generator’s acoustic emission is also necessary, and can be accomplished within the ECS system. Plug flow mufflers are commonly used, as they provide a sufficient level of noise attenuation in a compact structure. The key design parameter is the transmission loss of the muffler, as this dictates the level of attenuation at a given frequency. This work implements an analytically decoupled solution, using multiple perforate impedance models, through the transfer matrix method (TMM) to predict the transmission loss based on the muffler geometry. An equivalent finite element model is implemented for numerical simulation. The analytical results and numerical results are then evaluated against experimental data from literature.

This study investigates the life cycle greenhouse gas (GHG) emissions of a set of vehicles using two real-world gliders (vehicles without powertrains or batteries); a steel-intensive 2013 Ford Fusion glider and a multi material lightweight vehicle (MMLV) glider that utilizes significantly more aluminum and carbon fiber. These gliders are used to develop lightweight and conventional models of internal combustion engine vehicles (ICV), hybrid electric vehicles (HEV), and battery electric vehicles (BEV). Our results show that the MMLV glider can reduce life cycle GHG emissions despite its use of lightweight materials, which can be carbon intensive to produce, because the glider enables a decrease in fuel (production and use) cycle emissions. However, the fuel savings, and thus life cycle GHG emission reductions, differ substantially depending on powertrain type. Compared to ICVs, the high efficiency of HEVs decreases the potential fuel savings.

Biodiesel and other renewable fuels are of interest due to their impact on energy supplies as well as their potential for carbon emissions reductions. Waste animal fats from meat processing facilities, which would otherwise be sent to landfill, have been proposed as a feedstock for biodiesel production. Emissions from biodiesel fuels derived from vegetable oils have undergone intense study, but there remains a lack of data describing the emissions implications of using animal fats as a biodiesel feedstock. In this study, emissions of NOx, unburned hydrocarbons and particulate matter from a compression ignition engine were examined. The particulate matter emissions were characterized using gravimetric analysis, elemental carbon analysis and transmission electron microscopy. The emissions from an animal fat derived B20 blend were compared to those from petroleum diesel and a soy derived B20 blend.

We have studied the effects of water droplets presence in the PEM Fuel cell channel and the way they influence dynamics of the two-phase flow in the channel numerically. Dynamic behavior of a droplet on the surface of a channel has been modeled under the influence of surrounding fluid. Optimal conditions for the displacement of water droplet in the channel flow sought. For this purpose, the yield conditions for the displacement of liquid droplet on the surface of the channel under the influence of channel fluid are determined. The numerical solution is based on solving Navier-Stokes equations for Newtonian liquids. The study includes the effect of interfacial forces with constant surface tension, also effect of adhesion between the wall and droplet accounted by implementing contact angle at the wall. The Volume-Of-Fluid method is used to numerically determine the deformation of free surface.

Thermoplastic Vulcanizate (TPV) is a special class of Thermoplastic Elastomers (TPEs) made of a rubber/plastic polymer mixture in which the rubber phase is highly vulcanized. It is prepared by melt mixing a thermoplastic with an elastomer and by in-situ crosslinking of the rubber phase. Currently, TPV is replacing EPDM rubber dramatically because of the impressive advantages for automotive sealing applications. Some of the advantages of TPV compared to that of EPDM rubber are good gloss, recyclability, improved colorability, shorter cycle time and design flexibility. The development of TPV foaming technology is to fulfill the requirement of achieving lower cost, lighter weight and better fuel economy. Foaming of TPV has not been investigated extensively.

TPO is being used to make automotive parts for its number of advantages: i) low temperature flexibility and ductility, ii) excellent impact/stiffness/flow balance, iii) excellent weatherability, and iv) free-flowing pellet form for easy processing, storage, and handling. However, by foaming TPO, due to its higher rigidity-to-weigh ratio, it would offer additional advantages over the solid counterparts in terms of reduced weight, reduced material cost, and decreased fuel usage without compromising their performance. Since a major component in TPO is polypropylene (PP), understanding PP foaming behaviours is an important step towards understanding TPO foaming. For foam materials, cell density and cell size are two significant parameters that affect their material properties. In this research, we observed the cell nucleation and initial growth behaviours of PP foams blown with CO2 under various experimental conditions in a batch foaming simulation system.

Foaming of a thermoplastic polyolefin (TPO) is gaining interests because of its superior mechanical properties of foamed automotive parts, such as lightweight and high performance to weight ratio, etc. In this context, understanding of the thermophysical properties of PP/gas and TPO/gas mixtures is critically important. This paper will present the newly developed experimental technique to accurately measure the swelling of PP and TPO due to gas dissolution at elevated temperatures and pressures. Our technique measures the geometry of the pendent drop accurately from the captured images to obtain the volume swelling data. It determines the boundary location of the polymer/gas sample accurately by magnifying the sample drop locally along its edge before capturing the image. The automated high-precision XY stage is chosen as the platform to control the motion of the CCD camera.

This paper presents an experimental study on the foaming behavior of recyclable high-melt-strength (HMS) branched polypropylene (PP) with CO2 as a blowing agent. The foamability of branched HMS PP has been evaluated using a tandem foaming extruder system. The effects of CO2 and nucleating agent contents on the final foam morphology have been thoroughly investigated. The low density (i.e., 12~14 fold), fine-celled (i.e., 107–109 cells/cm3) PP foams were successfully produced using a small amount of talc (i.e., 0.8 wt%) and 5 wt% CO2.

Foaming of thermoplastic polyolefins (TPO) and thermoplastic elastomers (TPE) is gaining interest because of the lightweight and high performance to weight ratio of foamed automotive parts. Since foaming will occur mainly in the PP matrix in these PP-based automotive materials, understanding of the thermophysical properties of PP/gas mixtures is critically important. This paper will present a proposed methodology for measuring the swelling of polymer/gas mixtures. The preliminary experimental measurement of PP/N2 swelling at elevated temperatures and pressures will be discussed.

This paper demonstrates the effects of nano-clay on the microcellular foam processing of nylon. First, Nylon 6 nanocomposites with 1 wt% clay were prepared by a twin screw extruder. The nanocomposite structures were characterized by XRD and TEM. Nylon and its nanocomposites were foamed in extrusion using CO2. The cell morphologies of nylon and its nanocomposite foams were investigated. It appeared that the nano-clay not only enhanced cell nucleation, but also suppressed cell deterioration in the microcellular foaming of nylon.

Eco-efficient and cost effective natural fibre - thermoplastic composites have gained attention to a great extent in the automotive industry. Most of the OEM specifications for automotive interior parts, for example, instrument panels, recommend the composite should have a minimum flexural modulus of 1900 MPa, a notched Impact strength greater than 150 J/m at room temperature and a melt flow index of 5 g/10min and above [1, 2 and 3]. The objective of this work was to develop a high performance hybrid composite by injection molding process of the composites made from natural fibre in combination with glass fibre or calcium carbonate in a thermoplastic matrix to meet the specifications required for automotive interior parts applications. Mechanical properties, such as tensile and flexural strengths and moduli of the composites prepared, were found to be highly promising.

A comparison of scanning mobility particle sizer (SMPS) and laser-induced incandescence (LII) measurements of diesel particulate matter (PM) was performed. The results reveal the significance of the aggregate nature of diesel PM on interpretation of size and volume fraction measurements obtained with an SMPS, and the accuracy of primary particle size measurements by LII. Volume fraction calculations based on the mobility diameter measured by the SMPS substantially over-predict the space-filling volume fraction of the PM. Correction algorithms for the SMPS measurements, to account for the fractal nature of the aggregate morphology, result in a substantial reduction in the reported volume. The behavior of the particulate volume fraction, mean and standard deviation of the mobility diameter, and primary particle size are studied as a function of the EGR for a range of steady-state engine speeds and loads for a turbocharged direct-injection diesel engine.

Crevices in the combustion chamber are the main source of hydrocarbon (HC) emissions from spark ignition (SI) engines fuelled by natural gas (NG). Instantaneous in-cylinder and engine exhaust port HC concentrations were measured simultaneously using a Cambustion HFR400 fast response flame ionization detector (FRFID) concentrated on the post-flame period. The raw data was reconstructed to account for variation in the FFRID sample transit time and time constant due to fluctuating in-cylinder pressure. HC concentration development during the post-flame period is discussed. Comparison is made of the post-flame in-cylinder and exhaust port HC concentrations under different engine operating conditions, which gives a better understanding of the mechanism by which HC emissions form from crevices in SI engines.

A counter–flow propane/air diffusion flame (ϕ= 1.79) is used for a fundamental analysis of the effects of oxygenated additives on soot precursor formation. Experiments are conducted at atmospheric pressure using Gas Chromatography for gas sample analysis. The oxygenated additives dimethyl carbonate (DMC) and ethanol are added to the fuel keeping the total volumetric fuel flow rate constant. Results show 10 vol% DMC significantly reduces acetylene, benzene, and other flame pyrolysis products. Ethanol (10 vol%) shows, instead, more modest reductions. Peak acetylene and benzene levels decrease as the additive dosage increases for both DMC and ethanol. The additive's effect on the adiabatic flame temperature and the fuel stream carbon content does not correlate significantly with acetylene levels. However, there does appear to be a linear relationship between acetylene concentrations and both the additive's oxygen and C–C bond content.

The Cambustion fast-response flame ionization detector (FFID) has been successfully used for instantaneous exhaust port hydrocarbon (HC) concentration measurement in IC engines for a decade. Measurements of in-cylinder HC concentration have also been made, but these present greater challenge. As the sample transit time and the time constant of the system always change when the sampling pressure is changed, it is necessary to investigate the characteristics of the system before it was used for in-cylinder sampling. A unique method was designed to study the influence of the diameter and length of the transfer sample line and the operating parameters of the FFID on the transit time and time constant. A database of transit time and time constant was built up for different simulated in-cylinder pressures. The database can be used for correcting eventual in-cylinder HC concentration measurement.