Search Results

The requirements of the automotive industry move along due to product competitiveness and this contributes to increase complexity in the requirements for evaluation. Simulation tools play a key role thanks to their versatility and multiple physical phenomena that can be represented. The axis of analysis for this paper is the problem of the interaction of airflow and water flow in the cowl/plenum/leaf screen components. Airflow is represented by HVAC system operating and water flow by the vehicle in torrential rain. Initially, one simulation is evaluated at a time, in one side, the airflow entering the HVAC system in which the amount of air entering is monitored and pressure drop, on the other, the water simulation on the vehicle, both using a Lagrangian CFD model (using with tools such as STAR CCM+® or Ansys Fluent®) Due to this, a CFD methodology was developed to evaluate the interaction of air and water flow.

This study investigated the potential of generating reactive chemical species (including radicals) through pilot fuel injection in negative valve overlap for improving the combustion and emissions performances of spark ignition gasoline engines under low load and low speed operating conditions. Several Ford sub-models were used for simulating the physics and chemistry processes of injecting a small amount of fuel in NVO (negative valve overlap). Effects of different NVO degrees and different pilot injection timings, factors for fuel conversion were simulated and investigated. CO and H2 conversions during NVO, CO and H2 amounts before spark timing were used for comparing different schemes.

Variable Displacement Oil Pump (VDOP) is becoming the design of choice for engine friction reduction and fuel economy improvement. Unfortunately, this pump creates excessive pressure ripples, at the outlet port during oil pump shaft rotation, causing oscillating forces within the lubrication system and leading to the generation of objectionable tonal noises and vibrations. In order to minimize the level of noise, different vanes spacing and porting geometries are used. Moreover, an oil pressure relief groove can be added, at the onset of the high pressure port, to achieve this goal. This paper presents an optimization method to identify the best geometry of the oil pressure relief groove. This method integrates adaptive meshing, 3D CFD simulation, Matlab routine and Genetic Algorithm based optimization. The genetic algorithm is used to create the required design space in order to perform a multi-objective optimization using a large number of parameterized groove geometries.

Under the competitive pressure of automotive industry the customer’s focus is on a vehicle’s quality perception. Side door closing efforts make a considerable share of the overall impression as the doors are the first physical and haptic interface to the customer. Customer’s subjective feeling of vehicle quality demands for detailed analysis of each contributor of door closing efforts. Most contributors come from kinematic influences. Beside the losses due to mechanical subsystems like the checkarm, latch or hinge friction one of the biggest impacts originates from the pressure spike that builds up due to air being pushed into the cabin. Subject of this publication is to discuss the dependencies of closing efforts on cabin pressure and air extraction. It demonstrates an approach to simulate the development of the air pressure during door closing motions and the validation of the simulation method with the “EZ-Slam” measurement device.

A traditional vane type oil pump used inside the engines and the transmissions has equal angles or spacing between the vanes. The equal spacing intensifies pressure fluctuations generated within the pump leading to narrowband pressure spikes at the pump main order and its harmonics. Unequal spacing, however, can relax the severity of the spikes by breaking down the narrowband peaks and distributing them over a larger frequency range. Optimization of the angles within the pump design constraint can maximize the benefit of unequal spacing in reducing the pressure pulsations for a lower risk of engine or transmission whine. The scope of this paper is around the optimization process for vane spacing and different objective functions which can be used to obtain optimized solutions. The simulation results for optimized spacing based on two different objective functions for 7, 8 and 9 vanes are presented. The design constraints for the optimization are discussed as well.

The current work demonstrates effective suppression of compression system surge instabilities by installing a variable cross-sectional flow area restriction within the inlet duct of a turbocharger centrifugal compressor operating on a bench-top facility. This restriction couples with the compressor, similar to stages in a multi-stage turbomachine, where the effective pressure ratio is the product of those for the restriction and compressor. During experiments at constant compressor rotational speed, the compressor is stable over the negatively sloped portion of the pressure ratio vs. flow rate characteristics, so the restriction is eliminated within this operating region to preserve compressor performance. At low flow rates, the slope of the compressor alone characteristics reaches a positive value, and the unrestricted compression system enters mild surge. Further reduction of flow rate with the unrestricted compressor inlet results in a sudden transition to deep surge instabilities.

The need for gasoline particulate filter (GPF) technology is expected to grow with increasingly tight particle emissions standards being implemented in US, EU, China and elsewhere. Derived from the successful experience with diesel particulate filters (DPF), GPFs adopted the characteristic alternately plugged honeycomb structure that provides a large area of porous cordierite wall for filtering particles with minimal additional backpressure. However, unlike DPFs, continuous soot regeneration in GPFs makes it difficult to grow and sustain the soot cake on the filter wall that gives DPFs their high filtration efficiency. Therefore, filtration performance of low mileage GPFs relies heavily on the porous structure of filter media, which depends on both the substrate and the applied washcoat. In this work, a blank, two fresh washcoated filters and two washcoated filters with 3000 km mileage accumulation were characterized to compare their filtration performance.

The initiative of this paper is focused on improving the heat dissipation from the pressure wheel of a laser welding assembly in order to achieve a longer period of use. The work examines the effects of different geometrical designs on the thermal performance of pressure wheel assembly during a period of cooling time. Three disc designs were manufactured for testing: Design 1 – a plain wheel, Design 2 – a pierced wheel, and Design 3 – a wheel with ventilating vanes. All of the wheels were made of carbon steel. The transient thermal reaction were compared. The experimental results indicate that the ventilated wheel cools down faster with the convection in the ventilated channels, while the solid plain wheel continues to possess higher temperatures. A comparison among the three different designs indicates that the Design 3 has the best cooling performance.

A jet pump (also known as ejector) uses momentum of a high velocity jet (primary flow) as a driving mechanism. The jet is created by a nozzle that converts the pressure head of the primary flow to velocity head. The high velocity primary flow exiting the nozzle creates low pressure zone that entrains fluid from a secondary inlet and transfers the total flow to desired location. For a given pressure of primary inlet flow, it is desired to entrain maximum flow from secondary inlet. Jet pumps have been used in automobiles for a variety of applications such as: filling the Fuel Delivery Module (FDM) with liquid fuel from the fuel tank, transferring liquid fuel between two halves of the saddle type fuel tank and entraining fresh coolant in the cooling circuit. Recently, jet pumps have been introduced in evaporative emission control system for turbocharged engines to remove gaseous hydrocarbons stored in carbon canister and supply it to engine intake manifold (canister purging).

The effects of substituting a 12 mm thick subcool on top condenser in place of a 16 mm subcool on bottom condenser are evaluated in a vehicle level AC pull down test. The A to B testing shows that a thinner condenser with subcool on top exhibits no degradation in AC performance while resulting in a lower total system refrigerant charge. The results are from vehicle level tests run in a climatically controlled vehicle level wind tunnel to simulate an AC pull down at 43°C ambient. In addition to cabin temperature and AC vent temperatures, comparison of compressor head pressures was also done. The conclusion of the study was that a standard 16 mm thick subcool on bottom IRD condenser can be replaced by a 12 mm thick subcool on top IRD condenser with no negative effects on performance.

The natural refrigerant, R744 (CO2), remains a viable solution to replace the high GWP refrigerant R134a which is to be phased out in light-duty vehicles in EU and US market. In this study, thermodynamic analysis is performed on a R744 parallel compression system to evaluate its potential in automotive climate control. The model adopts a correlation of isentropic efficiency as a function of compression ratio based on a prototype R744 MAC compressor and accounts for the operating limits defined in the latest DIN specifications. Optimization is run over typical MAC operating conditions which covers both transcritical and subcritical domain. Comparing to the conventional single compression cycle, effectiveness of parallel compression is found most pronounced in low evaporating temperature and high ambient conditions, with up to 21% increase in COP and 5.3 bar reduction in discharge pressure observed over the considered parametric range.

An accurate estimation of cycle-by-cycle in-cylinder mass and the composition of the cylinder charge is required for spark-ignition engine transient control strategies to obtain required torque, Air-Fuel-Ratio (AFR) and meet engine pollution regulations. Mass Air Flow (MAF) and Manifold Absolute Pressure (MAP) sensors have been utilized in different control strategies to achieve these targets; however, these sensors have response delay in transients. As an alternative to air flow metering, in-cylinder pressure sensors can be utilized to directly measure cylinder pressure, based on which, the amount of air charge can be estimated without the requirement to model the dynamics of the manifold.

Weld lines occur when melt flow fronts meet during the injection molding of plastic parts. It is important to investigate the weld line because the weld line area can induce potential failure of structural application. In this paper, a weld line factor (W-L factor) was adopted to describe the strength reduction to the ultimate strength due to the appearance of weld line. There were two engineering thermoplastics involved in this study, including one neat PP and one of talc filled PP plastics. The experimental design was used to investigate four main injection molding parameters (melt temperature, mold temperature, injection speed and packing pressure). Both the tensile bar samples with/without weld lines were molded at each process settings. The sample strength was obtained by the tensile tests under two levels of testing speed (5mm/min and 200mm/min) and testing temperatures (room temperature and -30°C). The results showed that different materials had various values of W-L factor.

A novel 0-D Probability Density Function (PDF) based approach for the modelling of Diesel combustion using tabulated chemistry is presented. The Direct Injection Stochastic Reactor Model (DI-SRM) by Pasternak et al. has been extended with a progress variable based framework allowing the use of a pre-calculated auto-ignition table. Auto-ignition is tabulated through adiabatic constant pressure reactor calculations. The tabulated chemistry based implementation has been assessed against the previously presented DI-SRM version by Pasternak et al. where chemical reactions are solved online. The chemical mechanism used in this work for both, online chemistry run and table generation, is an extended version of the scheme presented by Nawdial et al. The main fuel species are n-decane, α-methylnaphthalene and methyl-decanoate giving a size of 463 species and 7600 reactions.

This study investigates the use of a characteristic reaction time as a possible method to speed up automotive knock calculations. In an earlier study of HCCI combustion it was found that for ignition at TDC, the ignition delay time at TDC conditions was required to be approximately 10 crank angle degrees (CAD), regardless of engine speed. In this study the analysis has been applied to knock in SI engines over a wide range of engine operating conditions including boosted operation and retarded combustion phasing, typical of high load operation of turbocharged engines. Representative pressure curves were used as input to a detailed kinetics calculation for a gasoline surrogate fuel mechanism with 312 species. The same detailed mechanism was used to compile a data set with traditional constant volume ignition delays evaluated at the peak pressure conditions in the end gas assuming adiabatic compression.

This paper proposes a method to make diagnostic/prognostic judgment about the health of a tire, in term of its wear, using existing on-board sensor signals. The approach focuses on using an estimate of the effective rolling radius (ERR) for individual tires as one of the main diagnostic/prognostic means and it determines if a tire has significant wear and how long it can be safely driven before tire rotation or tire replacement are required. The ERR is determined from the combination of wheel speed sensor (WSS), Global Positioning sensor (GPS), the other motion sensor signals, together with the radius kinematic model of a rolling tire. The ERR estimation fits the relevant signals to a linear model and utilizes the relationship revealed in the magic formula tire model. The ERR can then be related to multiple sources of uncertainties such as the tire inflation pressure, tire loading changes, and tire wear.

The characteristics of gasoline sprayed directly into combustion chambers are of critical importance to engine out emissions and combustion system development. The optimization of the spray characteristics to match the in-cylinder flow field, chamber geometry, and spark location are vital tasks during the development of an engine combustion strategy. Furthermore, the presence of liquid fuel during combustion in Spark-Ignition (SI) engines causes increased hydro-carbon (HC) emissions [1]. Euro 6, LEVIII, and US Tier 3 emissions regulations reduce the allowable particulate mass significantly from the previous standards. LEVIII standards reduce the acceptable particulate emission to 1 mg/mile [2]. A good DISI strategy vaporizes the correct amount of fuel just in time for optimal power output with minimal emissions. The opening and closing phases of DISI injectors is crucial to this task as the spray produces larger droplets during both theses phases.

Engine-Off Natural Vacuum (EONV) principles based leak detection monitors are designed to determine the presence of a small leak in the fuel tank system. It was introduced to address the ever more stringent emission requirement (currently at 0.02”) for gasoline engine equipped vehicles as proposed by the Environmental Protection Agency (EPA) and California Air Resources Board (CARB) in the United States [2, 3]. Other environmental protection agencies including the ones in EU and China will be adopting similar regulations in the near future. Due to its sensitivity to known noise factors such as the ambient temperature, barometric pressure, drive pattern and parking angle, it has been historically a lower performing monitor that is susceptible to warranty cost or even voluntary recalls. The proposed new model based monitor utilizes production pressure signal and newly instrumented temperature sensors [15].

High frequency variations in crankcase pressure have been observed in Inline-four cylinder (I4) engines and an understanding of the causes, frequency and magnitude of these variations is helpful in the design and effective operation of various engine systems. This paper shows through a review and explanation of the physics related to engine operation followed by comparison to measured vehicle data, the relationship between crankcase volume throughout the engine cycle and the observed pressure fluctuations. It is demonstrated that for a known or proposed engine design, through knowledge of the key engine design parameters, the frequency and amplitude of the cyclic variation in crankcase pressure can be predicted and thus utilized in the design of other engine systems.

While not commonly in production today, Gasoline Particulate Filters (GPFs) are likely to see widespread deployment to meet stringent EU6.2 and China particulate number (PN) standards. In many ways the operating conditions for GPFs are orthogonal to those of their diesel counterparts, and this leads to different and interesting requirements for the control strategy. We will present some generic system architectures for exhaust systems containing a GPF and will lay out an architecture for the GPF control strategy components which include: regeneration assist feature, soot estimation algorithm, GPF protection. The regeneration assist feature uses spark retard to increase exhaust temperature. The soot estimation algorithm describes how we can estimate soot from an open loop model or from a normalized pressure metric. The GPF protection feature controls oxygen flow to limit the soot burn rate. We will show validation data of the control strategy under different operating conditions.