Search Results

Based on the particularity of the racing field of the Baja SAE China, the Baja Racing Team of our university has adopted rzeppa universal joint for vehicle design and field competition in the semi-axle parts of the race car in previous years. In view of the complex conditions of the Baja Competition, such as gravity test, climb test, handling test, endurance test, etc., it is necessary to optimize and develop a more convenient maintenance model. Installation and use of better performance, more suitable for off-road conditions of the shaft. In this paper, based on the development dynamics of automobile axles and the transverse comparison of various axles, a kind of telescopic cross-shaft universal joint axles is designed by using CATIA software to model and simulate kinematics and dynamics by using ANSYS software. At the same time, the stress and strain of the model are continuously optimized according to the change of axle wheel Angle and the torque matching of Baja Racing.

Gear vibration and noise evaluation approaches are commonly proposed with a variety of way in a transmission system while complicated and obscured, it is difficult to provide a feasible basis for the gear development of E-drive system.

Preventing skidding is essential for studying the safety of driving in curves. However, the adhesion of the vehicle during the driving process on the wet and slippery road will be significantly reduced, resulting in lateral slippage due to the low adhesion coefficient of the road surface, the speed exceeding the turning critical, and the turning radius being too small when passing through the corner. Therefore, to reduce the incidence of traffic accidents of passenger cars driving in curves on rainy and snowy days and achieve the purpose of planning safe driving speed, this paper proposes a curve active safety system based on a deep learning algorithm and vehicle dynamics model. First,we a convolutional neural network (CNN) model is constructed to extract and judge the characteristics of snow and ice adhesion on roads.

This paper addresses the brake pad particle emission during the braking process of a vehicle in motion. The frictional-constant contact between the disc brake and pads results in an increased temperature and wear of the pads. The emission of brake pad particles into the atmosphere leads to an increase in air pollution and hence becomes hazardous to the human body. In this paper, a wheel brake disc is installed in a ventilation system where the specific air flow is introduced in order to investigate the thermal performance and the emission of particles from the brake pads. A mathematical model using the fundamental parameters of the brake disc and ventilation system is established. The behavior of the heat transfer is studied using computational fluid dynamics (CFD). The particle emission rate from the pads is calculated under the assumption of uniform constant pressure distribution at the contact surface of the brake disc and pad.

The sweeper vehicle plays a very key role in maintaining the urban environment. If the sweeper vehicle can accurately and efficiently identify and classify the ground garbage in the working process, it can greatly improve the working efficiency of the sweeper vehicle and reduce the consumption of manpower. Although the deep learning algorithm based on DUC and PSPNet has high accuracy, the recognition speed is low. ENet is a lightweight network, which greatly improves efficiency, but significantly sacrifices accuracy. This paper presents an improved real-time detection lightweight network based on PSPNet, which takes into account the operation speed and accuracy. The network takes PSPNet as the backbone network, and increases the stride in the convolution process, to reduce the size of the feature map and reduce the amount of calculation.

Magnetically coupled resonance wireless power transmission technology (MCR-WPT), as a technological innovation in the electric vehicle industry, is of great significance to promote the development of the electric vehicle industry chain. The current wireless charging technology is affected by the design of the vehicle itself, the distance between the vehicle-mounted part of the wireless charging and the ground is not fixed. And the changeable parking attitude will cause the projection of the transmitting coil and the receiving coil to deviate. Therefore, reasonable matching of transmission frequency, matching impedance and other parameters is of great significance for optimizing power transmission efficiency. This paper establishes a mathematical model of transmission frequency, matching impedance, distance between two coils and wireless power transmission efficiency.

When dump trucks unload dusty materials, dust particles with a diameter of 1 to 75 microns slide out of the dump body and float into the air. Dust particles naturally settle down spending a few hours, which causes air pollution. People who work in this environment daily suffer serious physical harm. To study the movement of dust particles during the unloading process, a scaled-down model is used to simulate the process of dump truck unloading gravel, and a high frame rate camera is used to record the movement trajectory of dust particles during the unloading process. In this paper, by observing the movement process of unloading dust particles by dump trucks, based on the principle of dynamics, a mathematical model describing the unloading of dust particles in the dump body and a mathematical model of the diffusion of dust particles in the air are established. Take the small gravel sampled at the construction site as an example of the experiment.

The plug-in hybrid electric vehicle (PHEV) gradually moves into the mainstream market with its excellent power and energy consumption control, and has become the research target of many researchers. The energy management strategy of plug-in hybrid vehicles is more complicated than conventional gasoline vehicles. Therefore, there are still many problems to be solved in terms of power source distribution and energy saving and emission reduction. This research proposes a new solution and realizes it through simulation optimization, which improves the energy consumption and emission problems of PHEV to a certain extent. First, on the basis that MATLAB software has completed the modeling of the key components of the vehicle, the fuzzy controller of the vehicle is established considering the principle of the joint control of the engine and the electric motor.

The articulated steering system is widely used in engineering vehicles due to its high mobility and low steering radius. The design parameters have a vital impact on the selection of the steering system assemblies, such as the operation stroke, pressure, and force of the hydraulic cylinders during the steering process, which will affect the system weight. The system energy consumption is also relevant to the geometry parameters. According to the kinetic analysis of the steering system and dynamic analysis of the steering process, the kinetic model of an engineering vehicle steering system is built, and the length and pressure variation of the cylinder is calculated and validated by the field test. The influence of the factors is analyzed based on the established model. To lower the system weight, needed pressure, and force, the multi-objective particle swarm optimization method is initiated to optimize the geometry parameter of the articulated steering system.

According to the requirements of high transmission ratio and high load torque of high-speed electric drive axle planetary gear system, the design and analysis of fine-pitch planetary gear system with small modulus, small pressure angle and high full tooth height of are carried out. In order to improve the bearing capacity of gear and reduce gear meshing noise, the tooth profile modification parameters of gear system are optimized. In this paper, the tooth modification methods are analyzed and the gear train parameters are determined. The influence degree of different tooth modification methods on the transmission performance of the gear train is determined by orthogonal experiment method. The transmission error is reduced, the stress fluctuation is improved, and the gear meshing performance is greatly improved by adopting the appropriate modification scheme, which proves the effectiveness of the tooth modification scheme.

With the increasingly serious global environmental and energy problems, as well as the increasing number of vehicles, pure electric vehicles with its advantages of environmental protection, low noise and renewable energy, become an effective way to alleviate environmental pollution and energy crisis. Due to the current pure electric vehicle power battery technology is not perfect, the range of pure electric vehicle has a great limit. Through the braking energy recovery, the energy can be reused, the energy utilization rate can be improved, and the battery life of pure electric vehicles can be improved. In this paper, a pure electric vehicle is taken as the analysis object, and the whole vehicle analysis model is built. Through the comparative analysis, based on the driver's braking intention and vehicle running state, the braking energy recovery control strategy of double fuzzy control is proposed.

In order to study the influence of low-viscosity oil on automobile pollutant emissions reduction, three different 0W20 oil samples were prepared with oil 5W30 as the base oil. Parameters such as the oil viscosity, ash, and element content were tested at different stages, speeds, and accelerations of the Worldwide Harmonized Light Vehicles Test Cycle (WLTC). The results showed the effects of low-viscosity oil on exhaust emissions reduction were mainly concentrated in the low-speed and extra high-speed segment. At the low-speed segment, especially in the starting stage, carbon monoxide (CO), total hydrocarbon (THC), and non-methane hydrocarbon (NMHC) emissions can be reduced. The use of low ash oil can reduce nitrogen oxides (NOx) emissions; the methane (CH4) emissions can be reduced by increasing the Zinc (Zn) content in engine oil moderately.

The lightweight design of a vehicle can save manufacturing costs and reduce greenhouse gas emissions. For the off-road vehicle and truck, the chassis frame is the most important load-bearing assembly of the separate frame construction vehicle. The frame is one of the most assemblies with great potential to be lightweight optimized. However, most of the vehicle components are mounted on the frame, such as the engine, transmission, suspension, steering system, radiator, and vehicle body. Therefore, boundaries and constraints should be taken into consideration during the optimal process. The finite element (FE) model is widely used to simulate and assess the frame performance. The performance of the frame is determined by the design parameters. As one of the largest components of the vehicle, it has a lot of parameters. To improve the optimum efficiency, sensitivity analysis is used to narrow the range of the variables.

In order to improve the drivability of passenger cars with dual clutch transmission (DCT) and reveal the criteria for objective evaluation criteria and characteristic index and feature index division of vehicles under specific working conditions, a drivability evaluation system that integrates data-driven and the consistency between subjective and objective is proposed. At first, combined with the control principle and dynamics theory of specific working conditions, a quantitative index system of vehicle drivability is constructed, including three modules: data source, evaluation working conditions and objective indicators. Then, a novel intelligent drivability objective evaluation tools (I-DOET) is designed, including data acquisition, de-noising, working condition recognition, feature extraction and automatic scoring.

To study the mechanism of the effect of low-viscosity oils on engine friction loss reduction so as to improve the vehicle fuel economy of the Worldwide harmonized Light vehicles Test Cycle (WLTC) by upgrading the Society of Automotive Engineers (SAE) viscosity grade of the factory fill oil from 5W30 to 0W20, eight 0W20 oil samples were blended with different doses of base oil, viscosity modifier (VM), and friction modifier (FM). Theoretical analysis by AVL-EXCITE simulation of the key friction pairs combined with practical engine friction torque test and vehicle WLTC fuel consumption tests were carried out. The results showed that 0W20 oils can effectively reduce the engine friction torque by 5.64 Nm and the friction loss by 11.95% with the throttle fully opened; while with the throttle closed, the friction torque decreased by 3.53 Nm and the friction loss by 11.26%, resulting to the improvement of the vehicle WLTC fuel economy by 2.08%.

Correct shifting schedule of vehicle coasting mode play a vital role in improving vehicle comfort and economy. At present, the calibration of the transmission shifting schedule ignores the impact of vehicle’s dynamic mass. This paper proposes a method for optimizing the shifting schedule of the coasting modes with gear based on the dynamic mass identification of the vehicle. This method identifies the dynamic mass of the vehicle during driving and substitute them into the process of solving the shifting schedule parameters. Then we get the optimal shifting schedule. At first, establish the Extended Kalman Filter to Pre-process the experimental data, reducing errors caused by excessive data fluctuations. Then, establishing a weighted squares estimation model based on particle swarm optimization to identify the dynamic mass of the vehicle.

With the rapidly developing automotive industry and stricter environmental protection laws and regulations, lightweight materials, advanced manufacturing processes and structural optimization methods are widely used in body design. Therefore, in order to evaluate and improve the pedestrian protection during a collision, this paper presents an impact simulation modeling and structural optimization method for a sport utility vehicle engine hood made of carbon fiber reinforced plastic (CFRP). Head injury criterion (HIC) was used to evaluate the performance of the hood in this regard. The inner panel and the outer panel of CFRP hood were discretized by shell elements in LS_DYNA. The Mat54-55 card was used to define the mechanical properties of the CFRP hood. In order to reduce the computational costs, just the parts contacted with the hood were modeled. The simulations were done in the prescribed 30 impact points.

At present, many electric vehicles are often equipped with only a single-stage final drive. Although the single-stage speed ratio can meet the general driving requirements of electric vehicles, if the requirements of the maximum speed and the requirements for starting acceleration or climbing are met at the same time, the power demand of the drive motor is relatively large, and the efficient area of the drive motor may be far away from the operating area corresponding to daily driving. If the two-speed automatic transmission is adopted, the vehicle can meet the requirements of maximum speed, starting acceleration and climbing at the same time, reduce the power demand of the driving motor, and improve the economy under certain power performance. This is especially important for medium and large vehicles.

The drivability plays an important role for marketability and competitiveness of passenger car in meeting some customer requirements, which directly affects the driving experience and the desire of purchasing. In this paper, a framework of objective drivability evaluation with multi-source information fusion for passenger car is proposed. At first, according to vehicle powertrain system and optimization theory, certain vehicle performances, which are closely related to objective drivability are analyzed, including vehicle longitudinal acceleration, vehicle speed, engine torque, engine speed, gear position, accelerator pedal, brake signal and voltage signal. Then, combined with the evaluation criterion of signal-to-noise ratio (SNR), mean error (ME), root mean squared error (RMSE) and signal smoothness (SS), a de-noising method is developed for the drivability evaluation information.

In the passenger cabin of the parking under the summer sun, the air’s average temperature will reach about 60°C. Such temperature can cause discomfort to the person who has just entered the passenger cabin, also can damage components of the passenger cabin. The reason for this phenomenon is because it is not convective with the outside air. Some vehicles use the electric power to drive the blower in order to ventilate, but the air’s temperature of cabin is so high that the blower’s effect of ventilation is limited. The system proposes to use solar energy to drive the automobile blower and the thermoelectric cooler(TEC) in order to cool the cabin’s air, and use the air-conditioning condensate water collected during the driving process to cool the TEC’s hot end to improve the cooling efficiency.