Refine Your Search

Date

Date

Topic

Topic

Technical review Washers Parts and Components Wear AGE-3 Aircraft Ground Support Equipment Committee

Search Results

Viewing 1 to 20 of 41
123Next >Last >>
Sort by published
Standard

Ground Support Equipment Hydraulic Systems, Design and Installation, Recommended Practices for
2022-12-16
CURRENT
ARP4943A
This SAE Aerospace Recommended Practice (ARP) covers the design and installation requirements for hydraulic systems (up to 8000 psig [56 MPa]) for ground support equipment (GSE). This ARP is derived from AS5440, which provides hydraulic system requirements for aircraft. The recommendations herein are primarily intended for GSE that exchange hydraulic fluid with the aircraft, such as hydraulic service carts, rather than GSE with non-interfacing hydraulic systems. The GSE may be mobile, portable, or stationary.
Standard

Aircraft Maintenance Jacks - General Requirements
2021-09-30
CURRENT
AS4775B
This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hangar. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word “shall”. Recommended criteria are identified by use of the key word “should”. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term “vertical load” throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.
Standard

Main Line Aircraft Tow Bar Attach Fitting Interface
2021-04-08
CURRENT
AS1614D
This SAE Aerospace Standard (AS) specifies the interface requirements for tow bar attachment fittings on the nose gear (when towing operations are performed from the nose gear) of conventional tricycle type landing gears of commercial civil transport aircraft with a maximum ramp weight higher than 50,000 kg (110,000 pounds), commonly designated as “main line aircraft”. Its purpose is to achieve tow bar attachment fittings interface standardization by aircraft weight category (which determines tow bar forces) in order to ensure that one single type of tow bar with a standard connection can be used for all aircraft types within or near that weight category, so as to assist operators and airport handling companies in reducing the number of different tow bar types used.
Standard

Design and Safety Criteria for Passenger Boarding Stairways
2012-03-28
CURRENT
ARP836C
This SAE Aerospace Recommended Practice (ARP) is broken into various categories for convenience and ease of identification. It is the purpose of this document to provide certain criteria for the design and selection of stairways, for the boarding of passengers onto an aircraft. The criteria presented are limited to those factors which affect the safety of the passengers and are coordinated, where applicable, with the practices of the architectural profession, with respect to the design of stairways. The recommended practices are applicable to both mobile variable-elevation type stairways and to fixed-elevation stairways of the type built into an aircraft fuselage.
Standard

Regional Aircraft Towbar Attach Fitting Interface
2011-06-20
CURRENT
AS5488A
This SAE Aerospace Standard (AS) specifies the interface requirements for towbar attachment fittings on the nose gear (when towing operations are performed from the nose gear) of conventional tricycle type landing gears of commercial civil transport aircraft with a maximum ramp weight between 8600 kg (19 000 lb) and 50 000 kg (110 000 lb), commonly designated as "regional aircraft". Its purpose is to achieve towbar attachment fittings interface standardization by aircraft weight category (which determines towbar forces) in order to ensure that one single type of towbar with a standard connection can be used for all aircraft types within or near that weight category, so as to assist operators and airport handling companies in reducing the number of different towbar types used.
Standard

Aircraft Maintenance Jacks - General Requirements
2011-01-14
HISTORICAL
AS4775A
This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hanger. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word “shall”. Recommended criteria are identified by use of the key word “should”. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term “vertical load” throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.
Standard

Aircraft Tow Bar
2010-09-13
HISTORICAL
ARP1915D
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8600 kg (19 000 lb).
Standard

Main Line Aircraft Tow Bar Attach Fitting Interface
2010-08-24
HISTORICAL
AS1614C
This SAE Aerospace Standard (AS) specifies the interface requirements for tow bar attachment fittings on the nose gear (when towing operations are performed from the nose gear) of conventional tricycle type landing gears of commercial civil transport aircraft with a maximum ramp weight higher than 50 000 kg (110 000 lb), commonly designated as “main line aircraft”. Its purpose is to achieve tow bar attachment fittings interface standardization by aircraft weight category (which determines tow bar forces) in order to ensure that one single type of tow bar with a standard connection can be used for all aircraft types within or near that weight category, so as to assist operators and airport handling companies in reducing the number of different tow bar types used.
Standard

400 Hz Connection Aircraft Electrical Maintenance Procedures
2008-03-28
HISTORICAL
AIR4365A
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

Aircraft Tow Bar
2005-04-06
HISTORICAL
ARP1915C
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8,600 kg (19,000 lb).
Standard

Method of Evaluating Pneumatic Ground Power Units
2003-11-21
HISTORICAL
AIR4545
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
123Next >Last >>
X